ViewSonic Projector PJD6221 User Manual

							
 EN-28
3. Select Intel Protocol (TCP/IP) and click Properties.
4. Set your PC’s IP address, and click 
OK.
„Click  Use the following IP address„The network address portion included in the IP address set into your PC 
should be common with projector’s one.
„ In this case, projector has “169.254.1.1” IP address, specify “169.254.1.xxx” 
for PC’s IP address. Select from 1 to 254 for “xxx” except 2 for PC. 
						

							
EN-29
5. Start browser in PC and specify following URL, then click “Go” button.
„URL: http://(Projector IP address)/
„For example, if projector IP address is 169.254.1.1, specify URL: http://
169.254.1.1/.
6. If connection succeeds, the login screen is displayed. Enter your User name and  Password and click “OK”. Below are the factory default settings for administrator, 
user and passwords.
)For setting passwords, please go to Network Control page > Password.
Item User name Password
Administrator Admin 
User User  
						

							
 EN-30
Control the projector via a web browserLogin
If the administrator and user passwords are disabled, it will directly go into the
Status page. 
						

							
EN-31
If the Administrator & User passwords are enabled, select your User Name and
enter password to login.
Authority on the network control of Administrator & User:
Item Description Administrator User
Status Show current projector status and network  configuration settings. vv
Control Control the projector via network. v v
Network Setting Network configuration & Password setup. v x
Alert Show and setup Alert configurations. v x
Schedule Show and setup Scheduling configurations. v v 
						

							
 EN-32
Status
All screen images in this manual are shown when you login with the Administrator ID.
The image will differ if you login with User ID.
Remark:
*If the power has not been supplied for over 36 hours, date and time will be reset.
Item Description
IP Address Show current IP address.
MAC Address Show current MAC Address.
Projector Name Show projector name.
System Status Show if projector is Powered ON or Standby *.
Input Status Show current input source.
Lamp Hours Show lamp used hours on current projector.
Filter Hours Show filter used hours on current projector.
System Temperature Show system temperature.
Projector Status Show current projector st atus, either function normally or error 
found.
F/W Version Show projectors F/W version
Date(mm/dd/yy) Show date set on current projector.
Time Show time set on current projector . 
						

							
EN-33
Control
Item Description
Basic
Power Switch Power On or Power Off the projector via network.
Input Source Select input source.
Date Show date set on current projector.
Time Show time set on current projector *.
Volume Adjusts the volume  setting. (0 - 20)
Mute Enable or disable the mute function.
Picture
Brightness Adjusts the brightness setting. (0 - 100)
Contrast Adjusts the contrast setting. (0 - 100)
Color Temperature Selects the color temperature setting.
Keystone Adjusts the keystone setting. (-40 - +40)
Picture Mode Selects the picture mode setting.
Aspect Ratio Selects the aspect ratio setting.
Freeze Enable or disable the freeze function.
Video Image
Color Adjusts the color setting. 
						

							
 EN-34
Remark:*If the power has not been supplied for over 36 hours, date and time will be reset.
Tint Adjusts the tint setting. (0 - 100)
Sharpness Adjusts the sharpness setting. (0 - 31)
Computer Image
Frequency Adjusts the frequency. (-50 - +50)
Tracking Adjusts the tracking. (0 - 31)
H Position Adjusts the horizontal position. (-10 - +10)
V Position Adjusts the vertical position. (-10 - +10)
Setting
Menu Position Adjusts the menu position.
Projection Selects the projection setting.
Auto Source Enable or disable the auto source function.
ECO mode Enable or disable the ECO function.
High Altitude Enable or disable the high altitude function.
OSD Timeout Selects the OSD timeout setting.
Language Selects preferred OSD language.
Factory Default Enable or Disable factory default.
Option
ViewMatch Selects ViewMatch setting.
White Intensity Adjusts white intensity setting.
Gamma Adjusts gamma setting.
Signal Type Selects signal type setting.
Filter Mode Selects filter mode setting.
Power Saving Selects power saving setting.
Start Up Screen Selects start-up screen setting.
Closed Caption Selects closed caption setting.
Blank Screen Selects blank screen setting.
„If the adjustment did not display properly. Please “refresh” or “reload” the 
browser again. 
						

							
EN-35
Network Setting
Click “Submit” button to save the settings.
Item Description
Network
DHCP Assign an IP address to the projector from the DHCP server  automatically or manually.
IP Address Setup IP address when DHCP is disable.
Subnet Mask Setup subnet mask when DHCP is disable.
Gateway Setup gateway when DHCP is disable.
DNS Server Setup DNS server address when DHCP is disable.
Group Name Create projector group. (Max length: 6 characters)
Projector Name Create projector naming of the current projector. (Max length: 15  characters)
Password
Administrator Enable or disable administrative password function.
New Password Setup administrative password. (Max length: 4 characters)
Confirm Password Re-enter administrative password.
User Enable or disable user password function.
New Password Setup user password. (Max length: 4 characters)
Confirm Password Re-enter user password. 
						

							
 EN-36
Alert
Click “Submit” button to save the settings, then click “Issue Test Mail” to send a test mail
to check whether all settings and functions are correct.
Item Description
Email Setting
To Setup the mail alert attendee. (Max length: 40 characters)
Cc Setup the backup mail alert attendee. (Max length: 40 characters)
Subject Setup the subject of the aler t e-mail. (Max length: 30 characters)
From Setup the sender e-mail address. (Max length: 40 characters)
Server To enter the SMTP server (Mail server) name of the company. For example: mail.viewsonic.co m (Max length: 30 characters)
User Name Enter user name of the sender’s e-mail account. (Max length: 20  characters)
Password Enter password of the sender’s e-mail account. (Max length: 14  characters)
Alert Condition
Fan Lock The cooling fan is not operating.
Over Temperature The projector internal is over heated.
Lamp Fail The lamp does not light up.
Lamp Time Alert Lamp is approaching the end of its useful life in full power  operation.
Replacement is suggested.
Schedule Execution ErrorSchedule Execution Error.
Filter Time AlertFilter is approaching the end of its useful life.
Replacement is suggested. 
						

							
EN-37
ScheduleThe schedule function is divided into two scheduling categories, as shown below:
Weekly Schedule: defines the date of  each week will execute the command
Click “Add” button to create new schedule.  To delete schedule, click “Cancel”. Specific
Day: defines the month and day that will execute the command.
Click “Submit” button to create new schedule. To delete schedule, click “Cancel”.