ViewSonic Projector PJD5232L User Manual

36
Hiding the image
In order to draw the audience's full attention to the presenter, you can use   on the 
projector or Blank on the remote control to hide the screen image. Press any key on the 
projector or remote control to restore the image. The word 'BLANK' appears at the lower 
right corner of the screen while the image is hidden.
You can set the blank time in the 
SYSTEM SETTING: BASIC > Blank Timermenu to
let the projector return the image automatically after a period of time when...

37
To activate the High Altitude Mode:
1. Press MENU/EXIT on the projector or Menu on 
the remote control and then press  /  until the 
SYSTEM SETTING: ADVANCED menu is 
highlighted.
2. Press  to highlight High Altitude Mode and 
press /  to select On. A confirmation 
message is displayed.
3. Highlight Yes and press MODE/ENTER on the projector or Enter on the remote 
control.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level 
because of increased fan speed...

38
2. Press  to highlight 3D Settings and press MODE/ENTER on the projector or 
Enter on the remote control.
3. Press  to highlight 3D Sync and press MODE/ENTER on the projector or Enter
on the remote control.
4. Press  to select a 3D Sync setting according to the table below and then press 
MODE/ENTER on the projector or Enter on the remote control to confirm.
For example, if the signal is input from the projector’s S-Video input socket, and its signal 
type (resolution) is 480i, then the default 3D...

39
Active Audio Out
Selecting On outputs an audio signal when the AUDIO IN and AUDIO OUT sockets are 
correctly connected to devices.
Quick Power Off
Selecting On enables the function and the projector will not enter the cooling process after 
being shut down. Selecting Off disables the function and the projector will enter normal 
cooling process after being shut down.
• If you attempt to restart the projector right after it’s been turned off, it may not be turned 
on successfully and will rerun its...

40
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected.
The menu items are available when the projector detects at least one valid signal. If there is 
no equipment connected to the projector or no signal detected, limited menu items are 
accessible.
Main menu Sub-menu Options
1.
DISPLAY
Screen ColorOff/Blackboard/Greenboard/
Whiteboard
Aspect RatioAuto/4:3/16:9/
16:10 (PJD5533w only)/Wide  
(PJD5533w only)/Anamorphic...

41
Main menu Sub-menu Options
3. SOURCE
Quick Auto Search Off/On
HDMI Format (PJD5134/PJD5234L/
PJD5533w only)RGB/YUV/Auto
HDMI Range (PJD5134/PJD5234L/
PJD5533w only)Enhanced/Normal
DynamicEco TimerDisable/5 min/10 min/15 min/
30 min
Smart Restart Off/On
Pattern Off/01/02/03/04/05
My ButtonProjection (Projector Position)/3D Sync/Lamp Mode/
DCR/Closed Caption/Auto Off (Auto Power Off)/
Message/Screen Color/CEC (PJD5134/PJD5234L/
PJD5533w only)/Auto Search (Quick Auto Search)/
Information
4.
SYSTEM...

42
5. 
SYSTEM
SETTING:
ADVANCED
High Altitude Mode On/Off
DCR On/Off
Audio SettingsMute On/Off
Volume
Menu SettingsMenu Display Time5 sec/10 sec/15 sec/20 
sec/25 sec/30 sec
Menu PositionCenter/Top-Left/Top-
Right/Bottom-Left/
Bottom-Right
Closed CaptionClosed Caption Enable On/Off
Caption Version CC1/CC2/CC3/CC4
Lamp SettingsLamp Mode Normal/Economic
Reset Lamp Timer
Equivalent Lamp Hour
Presentation TimerTimer Period 1~240 minutes
Timer DisplayAlways/1 min/2 min/3 min/
Never
Timer...

43
Main menu Sub-menu Options
6.
INFORMATIONCurrent System Status•Source
•Color Mode
•Resolution
•Color System
•Equivalent Lamp Hour 

44
Description of each menu
Function Description
Screen ColorCorrects the projected picture’s color when the projection surface is 
not white. See "Using Screen Color" on page 32 for details.
Aspect RatioThere are three options to set the image's aspect ratio depending on 
your input signal source. See "Selecting the aspect ratio" on page 28
for details.
KeystoneCorrects any keystoning of the image. See "Correcting keystone" on 
page 27 for details.
Position
Displays the...

45
Function Description
Color ModePre-defined picture modes are provided so you can optimize your 
projector image set-up to suit your program type. See "Selecting a 
picture mode" on page 31 for details.
Reference
ModeSelects a picture mode that most suits your need for the image quality 
and further fine-tune the image based on the selections listed on the 
same page below. See "Setting the User 1/User 2 mode" on page 32
for details.
BrightnessAdjusts the brightness of the image. See...