ViewSonic Projector PJ758/PJ759/PJ760 User Manual

							ViewSonic
46PJ758/PJ759/PJ760
Item Description
SECURITY
(continued)1.3 If you have forgotten your PASSWORD
1.3-1  Follow the procedure in 1.1-1 to display the 
ENTER PASSWORD box.
1.3-2  While the ENTER PASSWORD box is 
displayed, press and hold the RESET 
button for about 3 seconds or press and 
hold the INPUT and ► buttons on the 
projector for about 3 seconds.
The 10-digit Inquiring Code will be displayed.
• If there is no key input for about 55 seconds while the Inquiring Code is 
displayed the menu will close. If necessary repeat the process from 1.3-1.
1.3-3  Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD 
will be sent after your user registration information is confi rmed.
2. Using the MyScreen PASSWORD Function
The MyScreen PASSWORD function can be used to prohibit access to the 
MyScreen function and prevent the currently registered MyScreen image 
from being overwritten.
2.1 Turning on the MyScreen PASSWORD Function
2.1-1  Use the ▲/▼ buttons on the SECURITY 
menu to select MyScreen PASSWORD 
and press the ► button to display the 
MyScreen PASSWORD on/off menu.
2.2 Setting the PASSWORD
2.2-1  Display the MyScreen PASSWORD on/off menu using the procedure 
in 2.1-1.
2.2-2  Use the ▲/▼ buttons on the MyScreen 
PASSWORD on/off menu to select TURN ON.The ENTER PASSWORD box (small) will be 
displayed.
2.2-3  Use the ▲/▼/◄/► buttons to enter the 
PASSWORD. 
Move the cursor to the right side of the ENTER PASSWORD box (small) and press the ► 
button to display the PASSWORD AGAIN box, 
enter the same PASSWORD again.
OPTION Menu (continued)
OPTION Menu
(continued on next page) 
						

							ViewSonic
47PJ758/PJ759/PJ760
Item Description
SECURITY
(continued)
2.2-4  Move the cursor to the right side of the 
PASSWORD AGAIN box and press the 
► button to display the PASSWORD for 
about 20 seconds, please make note of the 
PASSWORD during this time. 
Pressing the ENTER button will return to 
MyScreen PASS WORD on/off menu.
When a PASSWORD is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock function (and menu) will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will 
be unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of both  
functions.
• Please do not forget your MyScreen PASSWORD.
2.3 Turning the PASSWORD off
2.3-1  Follow the procedure in 2.1-1 to display the MyScreen PASSWORD 
on/off menu.
2.3-2  Select TURN OFF to display the ENTER PASSWORD box (large). 
Enter the registered PASSWORD and the screen will return to the 
MyScreen on/off menu.
If an incorrect PASSWORD is input the menu will close. If necessary 
repeat the process from 2.3-1.
2.4 If you have forgotten your PASSWORD
2.4-1  Follow the procedure in 2.1-1 to display the MyScreen PASSWORD 
on/off menu.
2.4-2  Select TURN OFF to display the ENTER 
PASSWORD box (large). The 10-digit 
Inquiring Code will be displayed inside the 
box.
2.4-3  Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD 
will be sent after your user registration information is confi rmed.
3. Using the PIN LOCK Function
PIN LOCK is a function which prevents the projector from being used unless 
a registered Code is input.
3.1 Registering the PIN Code
3.1-1  Use the ▲/▼ buttons on the SECURITY menu 
to select PIN LOCK and press the ► button 
or the ENTER button to display the PIN LOCK 
on/off menu.
OPTION Menu (continued)
OPTION Menu
(continued on next page) 
						

							ViewSonic
48PJ758/PJ759/PJ760
Item Description
SECURITY
(continued)
3.1-2  Use the ▲/▼ buttons on the PIN LOCK 
on/off menu to select TURN ON and the 
PIN BOX will be displayed. 
3.1-3    Input a 4 part PIN Code using the ▲, ▼, 
◄, ►, COMPUTER and INPUT buttons.
A PIN Code again box will appear. Reenter 
the same PIN Code. This will complete the 
PIN Code registration.
• If there is no key input for about 55 seconds while the PIN BOX or the 
PIN Code again box are displayed the menu will close. If necessary 
repeat the process from 3.1-1.
Afterwards, anytime the projector is restarted after AC power is turned off 
the PIN BOX will be displayed. Enter the registered PIN Code.
The projector can be used after entering the registered PIN Code. If an 
incorrect PIN Code is input the PIN BOX will be displayed again.
If an incorrect PIN Code is input 3 times the projector will turn off. 
Afterwards the projector will turn off every time an incorrect PIN Code is 
input. The projector will also turn off if there is no key input for about 5 
minutes while the PIN BOX is displayed.
This function will activate only when the projector is started after AC 
power is turned off.
• Please do not forget your PIN Code.
3.2 Turning Off the PIN LOCK Function
3.2-1  Follow the procedure in 3.1-1 to display the PIN LOCK on/off menu. 
Use the ▲/▼ buttons to select TURN OFF and the PIN BOX will be 
displayed.
Enter the registered PIN Code to turn the PIN LOCK function off.
If an incorrect PASSWORD is entered the menu will close.
3.3 If you have forgotten your PIN Code
3.3-1  While the PIN BOX is displayed, press and 
hold the RESET button for 3 seconds or 
press and hold the INPUT and ► buttons 
for 3 seconds. The 10-digit Inquiring Code 
will be displayed.
• If it passes for about 5 minutes after the PIN BOX is displayed the 
projector will turn off.
3.3-2  Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD 
will be sent after your user registration information is confi rmed.
OPTION Menu (continued)
OPTION Menu
(continued on next page) 
						

							ViewSonic
49PJ758/PJ759/PJ760
Item Description
SECURITY
(continued)
4. Using the Transition Detector Function
While the Transition Detector function is ON, when power switch is started 
to supply to the projector, it might react as below.
• Transition Detector alarm shown below might appear on screen, if the 
projector has been moved or re-installed.
• Transition Detector alarm might appear on screen, if the MIRROR setting 
has been changed.
• Keystone adjustment feature has been prohibited as long as the Transition 
Detector function is ON.
4.1 Turning On the Transition Detector Function
4.1-1  Use the ▲/▼ buttons on the SECURITY 
menu to select TRANSITION DETECTOR and 
press the ► or the ENTER button to display 
the TRANSITION DETECTOR on/off menu.
Select TURN ON and the current angle and 
mirror setting will be recorded.
• This feature may not function properly if the projector is not in a stable 
position when TURN ON is selected.
4.1-2  If this function is set to TURN ON when 
the vertical angle of the projector or mirror 
setting at which the projector is turned on 
is different than the previously recorded the 
Transition Detector Alarm will be displayed 
and the projector will not display the input 
signal.
Set the Transition Detector off in the SECURITY menu to display the input 
signal.
If the Transition Detector ALARM is displayed for about 5 minutes the 
lamp will turn off. This function will activate only when the projector is 
started after turning off the AC power.
4.2 Setting the Transition Detector PASSWORD
4.2-1  Use the ▲/▼ buttons on the SECURITY menu to select TRANSITION 
DETECTOR and press the ► or the ENTER button to display the 
TRANSITION DETECTOR on/off menu.
4.2-2  Use the ▲/▼ buttons on the TRANSITION 
DETECTOR on/off menu to select TURN 
ON. The ENTER PASSWORD box (small) 
will be displayed.
4.2-3  Use the ▲/▼/◄/► buttons to enter a 
PASSWORD. Move the cursor to the right 
side of the ENTER PASSWORD box (small) 
and press the ► button to display the 
PASSWORD AGAIN box, enter the same 
PASSWORD again.
OPTION Menu (continued)
OPTION Menu
(continued on next page) 
						

							ViewSonic
50PJ758/PJ759/PJ760
Item Description
SECURITY
(continued)
4.2-4  Move the cursor to the right side of the 
PASSWORD AGAIN box and press the 
► button to display the PASSWORD for 
about 20 seconds, please make note of the 
PASSWORD during this time.
Pressing the ENTER button will return to the TRANSITION DETECTOR 
on/off menu.
• Please do not forget your Transition Detector PASSWORD.
4.3 Setting the Transition Detector off
4.3-1  Follow the procedure in 4.1-1 to display the TRANSITION DETECTOR 
on/off menu.
4.3-2  Select TURN OFF to display the ENTER PASSWORD box (large). 
Enter the registered PASSWORD and the screen will return to the 
TRANSITION DETECTOR on/off menu. If an incorrect PASSWORD is 
input the menu will close. If necessary repeat the process from 4.3-1.
4.4 If you have forgotten your PASSWORD
4.4-1  Follow the procedure in 4.1-1 to display the TRANSITION DETECTOR 
on/off menu.
4.4-2  Select TURN OFF to display the ENTER 
PASSWORD box (large). The 10-digit 
Inquiring Code will be displayed inside the 
box.
4.4-3  Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD 
will be sent after your user registration information is confi rmed.
OPTION Menu (continued)
OPTION Menu 
						

							ViewSonic
51PJ758/PJ759/PJ760
MaintenanceMaintenance
Lamp
A lamp has fi nite product life. Using the lamp for long periods of time could cause 
the pictures darker or the color tone poor. Note that each lamp has a different 
lifetime, and some may burst or burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended. To prepare 
a new lamp, contact your dealer and tell the lamp type number.
Type number : RLC-031
Replacing the lamp
1. Turn the projector off, and unplug the power cord. 
Allow the projector to cool for at least 45 minutes.
2. Prepare a new lamp. 
If the projector is mounted on a ceiling, or if the lamp 
has broken, also ask the dealer to replace the lamp. 
In case of replacement by yourself, follow the following procedure.
3. Loosen the screw (marked by arrow) of the lamp cover 
and then slide the lamp cover to the side to remove it.
4. Loosen the 2 screws (marked by arrow) of the 
lamp, and slowly pick up the lamp by the handles. 
5. Insert the new lamp, and retighten fi rmly the 
2 screws of the lamp that are loosened in the 
previous process to lock it in place. 
6. Slide the lamp cover back in place and fi rmly 
fasten the screw of the lamp cover.
7. Turn the projector on and reset the lamp time 
using the LAMP TIME item in the OPTION menu. 
(1) Press the MENU button to display a menu. 
(2) Point at the “Go to Advanced Menu …” in the menu 
using the ▼/▲ button, then press the ► button.
(3) Point at the “OPTION” in the left column of the menu 
using the ▼/▲button, then press the ► button.
(4) Point at the “LAMP TIME” using the ▼/▲ button, then press the ► button. A 
dialog will appear.
(5) Press the ▲ button to select “RESET” on the dialog. It performs resetting the 
lamp time.
Maintenance
NOTE  • Please reset the lamp time only when you have replaced the lamp, 
for a suitable indication about the lamp.
CAUTION  ►Do not touch any inner space of the projector, while the lamp 
is taken out.
Lamp cover
Handles 
						

							ViewSonic
52PJ758/PJ759/PJ760
Maintenance
Lamp (continued)
Lamp warning
 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
• If the lamp should break (it will make a loud bang when it does), 
unplug the power cord from the outlet, and make sure to request a 
replacement lamp from your local dealer. Note that shards of glass 
could damage the projector’s internals, or cause injury during handling, 
so please do not try to clean the projector or replace the lamp yourself.
• If the lamp should break (it will make a loud bang when it does), 
ventilate the room well, and make sure not to breathe the gas that 
comes out of the projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the power 
cord, then wait at least 45 minutes for the lamp to cool sufficiently. 
Handling the lamp while hot can cause burns, as well as damaging the 
lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from 
above. This is dangerous, since if the lamp’s bulb has broken, the 
shards will fall out when the cover is opened. In addition, working in 
high places is dangerous, so ask your local dealer to have the lamp 
replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp 
replacing, make sure that the screws are screwed in firmly. Loose 
screws could result in damage or injury.
• Use only the lamp of the specifi ed type.
• If the lamp breaks soon after the first time it is used, it is possible 
that there are electrical problems elsewhere besides the lamp. If this 
happens, contact your local dealer or a service representative.
• 
Handle with care: jolting or scratching could cause the lamp bulb to burst during use.• Using the lamp for long periods of time could cause it dark, not to light 
up or to burst. When the pictures appear dark, or when the color tone 
is poor, please replace the lamp as soon as possible. Do not use old 
(used) lamps; this is a cause of breakage. 
Disconnect 
the plug 
from the 
power 
outlet
WARNING  
►The projector uses a high-pressure mercury glass lamp. The 
lamp can break with a loud bang, or burn out, if jolted or scratched, handled 
while hot, or worn over time. Note that each lamp has a different lifetime, and 
some may burst or burn out soon after you start using them. In addition, when 
the bulb bursts, it is possible for shards of glass to fl y into the lamp housing, and 
for gas containing mercury to escape from the projector’s vent holes.
►About disposal of a lamp: This product contains a mercury lamp; do not put 
it in a trash. Dispose of it in accordance with environmental laws. 
•  For lamp recycling, go to www.lamprecycle.org. (in the US)
•  For product disposal, contact your local government agency 
or www.eiae.org (in the US) or www.epsc.ca (in Canada).
For more information, call your dealer. 
						

							ViewSonic
53PJ758/PJ759/PJ760
Please check and clean the air fi lter periodically. When the indicators or a 
message prompts you to clean the air fi lter, comply with it as soon as possible. 
Replace the air fi lter when it is damaged or too soiled. To prepare a new air fi lter, 
contact your dealer and tell the air fi lter type number.
When you replace the lamp, please replace the air fi lter. An air fi lter of specifi ed 
type will come together with a replacement lamp for this projector.
Cleaning the air fi lter
1. Turn the projector off, and unplug the power cord. 
Allow the projector to suffi ciently cool down.
2. Use a vacuum cleaner on and around the fi lter 
cover.
3. Pull the fi lter cover knobs while lifting it. The fi lter 
unit which consists of the fi lter’ cover, air fi lter and 
fi lter frame will come off.
4. Use a vacuum cleaner for the fi lter vent of the 
projector and the fi lter frame side of the fi lter unit. 
If the air fi lter is damaged or too soiled, replace it 
according to the following procedure number 5 to 7. 
Otherwise, please jump to the procedure number 8.
5. Pull the fi lter frame’ knob up while holding the fi lter 
cover. The fi lter frame will come off and the air 
fi lter will appear.
6. Replace the air fi lter with new one. 
7. Put the fi lter frame back.
8. Put the fi lter unit back into the projector.
9. Turn the projector on and reset the fi lter time using 
the FILTER TIME item in the EASY MENU. 
(1) Press the MENU button to display a menu. 
(2) 
Point at the “FILTER TIME” using the ▼/▲ button, then press the ► button. A dialog will appear.
(3) Press the ▲ button to select “RESET” on the dialog. It performs resetting the fi lter time.
Maintenance
Air fi lter
NOTE  • Please reset the fi lter time only when you have cleaned or 
replaced the air fi lter, for a suitable indication about the air fi lter.
• The projector may display the message such as “CHECK THE AIR FLOW” 
or turn off the projector, to prevent the internal heat level rising. 
WARNING  ►Before taking care of the air fi lter, make sure the power cable 
is not plugged in, then allow the projector to cool suffi ciently.
►
Use only the air fi lter of the specifi ed type. Do not use the projector without the 
air fi lter or the fi lter cover. It could result in a fi re or malfunction to the projector
.
►
Clean the air fi lter periodically. If the air fi lter becomes clogged by dust or the like, 
internal temperatures rise and could cause a fi re, a burn or malfunction to the projector.
Filter cover
Filter cover knobs
Filter unit
 Filter cover Filter frame
Air fi lter 
						

							ViewSonic
54PJ758/PJ759/PJ760
Maintenance
Inside of the projector
In order to ensure the safe use of your projector, please have it cleaned and 
inspected by your dealer about once every year.
Caring for the lens
If the lens is fl awed, soiled or fogged, it could cause deterioration of display 
quality. Please take care of the lens, being cautious of handling.
1. Turn the projector off, and unplug the power cord. Allow the projector to cool 
suffi ciently.
2. After making sure that the projector is cool adequately, lightly wipe the lens 
with a commercially available lens-cleaning wipe. Do not touch the lens 
directly with your hand.
Caring for the cabinet and remote control
Incorrect care could have adverse infl uence such as discoloration, peeling paint, 
etc.
1. Turn the projector off, and unplug the power cord. Allow the projector to cool 
suffi ciently.
2. After making sure that the projector is cool adequately, lightly wipe with gauze 
or a soft cloth.
If the projector is extremely dirty, dip soft cloth in water or a neutral cleaner 
diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a 
soft, dry cloth.
Other care 
WARNING  ►Before caring, make sure the power cable is not plugged in, 
and then allow the projector to cool suffi ciently. The care in a high temperature 
state of the projector could cause a burn and/or malfunction to the projector.
►Never try to care for the inside of the projector personally. Doing is so 
dangerous. 
►Avoid wetting the projector or inserting liquids in the projector. It could result 
in a fi re, an electric shock, and/or malfunction to the projector. 
• Do not put anything containing water, cleaners or chemicals near the 
projector. 
• Do not use aerosols or sprays.
CAUTION  ►Please take right care of the projector according to the 
following. Incorrect care could cause not only an injury but adverse infl uence 
such as discoloration, peeling paint, etc. 
►Do not use cleaners or chemicals other than those specifi ed in this manual. 
►Do not polish or wipe with hard objects. 
						

							ViewSonic
55PJ758/PJ759/PJ760
TroubleshootingTroubleshooting
If an abnormal operation should occur, stop using the projector immediately. 
Troubleshooting
Otherwise if a problem occurs with the projector, the following checks and 
measures are recommended before requesting repair.
If this does not resolve the problem, please contact your dealer or service 
company. They will tell you what warranty condition is applied.
Related messages
When some message appears, check and cope with it according to the following 
table. Although these messages will be automatically disappeared around several 
minutes, it will be reappeared every time the power is turned on.
Message Description
NO INPUT IS DETECTED