ViewSonic Projector PJ556D User Manual
Have a look at the manual ViewSonic Projector PJ556D User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 617 ViewSonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
26ViewSonic PJ556D 1. Turn off the projector and unplug the AC power cord. 2. Place a protect ve sheet (cloth) beneath the projector. Turn the projector over so you can access the lamp cover. 3. Loosen the access panel screws and open the panel. 4. Loosen the screws on the bottom of the lamp assembly. 5. Grasp the lamp handle and pull the lamp assembly d rectly out of the projector. 6. Replace w th the new lamp. 7. T ghten the screws on the bottom of lamp assembly. 8. T ghten the screws on the lamp cover. Dispose of the used lamp according to local regulations. Ensure that screws are tightened properly. Screws not tightened fully may result in injury or accidents. Since the lamp is made of glass, do not drop the unit and do not scratch the glass. Do not reuse the old lamp. This could cause the lamp to explode. Be sure to turn off the projector and unplug the AC power cord before replacing the lamp. Do not use the projector with the lamp cover removed.
ViewSonic PJ556D27 Specifications Display Type Single 0.55” DLP panel Resolution (Pixels) 1024 x 768 Lens Manual Zoom (1.2X) Aspect Ratio Auto, 16:9, 4:3 Screen Size 25” - 285” (Diagonal) Lamp 200W Projection Type Front, Rear, Ceiling Video Compatibility NTSC4.43 PAL-60, PAL-M,N,SECAM Input Source D-Sub 15 pin, S-Video, Composite Video, Stereo Phone Jack, RS232, USB Scanning Frequency Horizontal Frequency 31 - 79 KHz Vertical Frequency 56 - 85 Hz Digital Keystone Correction Vertical + / - 15° Integrated Speaker 1 x 1W Remote Control Multifunctional OSD Language Multilanguage Storage Temperature -20 - + 60°C Operation Temperature 0 - + 40°C Operation Humidity 30% - 85% maximum Power Requirement AC 100 – 240V, 50 / 60 Hz Power Consumption 250W (Typical) Dimension (W x D x H) 255.5 x 223 x 101.5 Weight 2.7 kgs (5.9 lbs) Note: Design and Specifications are subject to change without prior notice.
28ViewSonic PJ556D Appendix LED Indicator Messages Projector Status StandbyLamp ignition failure Power on Lamp life warning Power off Over temperature LED Type Power LEDLamp LED ColorStatusColorStatus Meaning Green Amber Amber - - - Flashing Solid Solid - - - - - Green Amber Green Amber - - Solid Solid Flashing Flashing The projector is powered and ready. The projector system has some problems with its fan, so the projector cannot start up. The projector is in good condition and is projecting at maximum brightness. The lamp has reached its end of life and must be changed soon. The lamp will continue to operate until it fails. Change the lamp. If the lamp is off, then the ballast will become malfunction. The projector is shutting down. The fan motor is cooling the lamp for shutdown. Do not unplug the power cord or turn the power switch off before the lamp LED turns off. The fan motor will turn off when the lamp has cooled. Temperature is too high. The lamp will turn off.
ViewSonic PJ556D29 Compatibility Modes Computer: Mode Resolution fH (kHz) fV (Hz) Timing 480P 640 x 480 31.46 59.9 60Hz VGA 640 x 480 37.86 72.8 60Hz VGA 640 x 480 37.5 75.0 75Hz VGA 640 x 480 43.2 85.0 85Hz VGA 720 x 400 31.5 70.0 60Hz VGA 720 x 400 37.9 85.0 85Hz SVGA 800 x 600 35.1 56.2 56Hz SVGA 800 x 600 37.8 60.3 60Hz SVGA 800 x 600 48.0 72.1 72Hz SVGA 800 x 600 46.8 75.0 75Hz XGA 1024 x 768 48.3 60.0 60Hz XGA 1024 x 768 56.4 70.0 70Hz XGA 1024 x 768 60.0 75.0 75Hz XGA 1024 x 768 68.8 84.9 85Hz Mac16” 832 x 624 49.7 74.5 60Hz SXGA 1280 x 1024 63.98 60.0 60Hz SXGA 1280 x 1024 79.9 75.0 75Hz 720P 1280 x 720 45.0 60.0 60Hz XGA 1024 x 768 48.3 60.0 60Hz XGA 1024 x 768 60.2 75.0 60Hz SXGA 1152 x 870 68.6 75.0 75Hz SXGA 1152 x 864 67.5 75.0 75Hz Mac 480-66A 640 x 480 35.0 66.7 66Hz Video: Signals Horizontal Frequency (kHz) Vertical Frequency (Hz) 480p 31.5 kHz 60 Hz 720p 45.0 kHz 60 Hz 1080 33.7 kHz 30 Hz
30ViewSonic PJ556D Troubleshooting Refer to the symptoms and measures l sted below before send ng the projector for repa rs. If the problem pers sts, contact your local reseller or serv ce center. Please refer to “LED Ind cator Messages” as well. Symptom No power. Power goes out during use. No image appears on screen. Partial, scrolling or incorrectly displayed image.Image is unstable or flickering. Image has vertical flickering bar. Image is out of focus. Cause The AC power cord s not plugged n. The AC power cord s not connected to the projector. The lamp cover s loose. The temperature s too h gh. The vent lat on holes are blocked. The projector s not turned on. The connect ons setup s not correctly. The connected dev ces are not funct on ng properly. Lens cap s not removed. “Blank” funct on s act vated. The nput s gnal s not supported by the projector. The s gnal t m ng of the d splay does not synchron ze w th the graph c card. The d splay data frequency does not match the frequency of your computer’s graph c card. The lens focus s not adjusted opt mally. The project on d stance s not w th n the projector’s supported range. Solution Plug n the AC power card. Connect the AC power cord to the projector correctly. T ghten the screws on the lamp cover. Unplug the AC power cord and wa t for a short wh le, then turn the power back on. Place the projector so that the vent lat on holes are not blocked. Turn the projector on. Check that all connect ons are setup correctly. Check that all connected dev ces are funct on ng properly. Remove the lens cap and turn the projector on. Cancel “Blank” funct on. Press remote control’s “Auto” button. Use “Phase” to correct t. Refer to P cture sect on. Change the mon tor color sett ng from your computer. Use “Track ng” to make an adjustment. Refer to P cture sect on. Check and reconfigure the d splay mode of your graph c card to make t compat ble w th the product. Adjust the focus w th the focus r ng. Place the projector w th n the supported range.
ViewSonic PJ556D31 Symptom Remote control doesn’t work. Cause The battery could be weak. The remote control s not be ng used w th n the effect ve range. There are some obstruct ons between the remote control and projector. There are some fluorescent or other br ght l ghts sh n ng at the projector’s nfrared remote sensor. Solution Replace w th a new battery. Use the remote control w th n the effect ve range. Check that there are not obstruct ons between the remote control and projector. Check that there are not any fluorescent or other br ght l ghts sh n ng at the projector’s nfrared remote sensor.
32ViewSonic PJ556D Customer Support For techn cal support or product serv ce, see the table below or contact your reseller. Note : You w ll need the product ser al number. Country/RegionWeb SiteT=Telephone F=FaxE-mail Un ted States www.v ewson c.com/support/ T= 800 688 6688 F= 909 468 1202 serv ce.us@v ewson c.com Canadawww.v ewson c.com/supportT= 866 463 4775serv ce.ca@v ewson c.com Un ted K ngdom www.v ewson ceurope.com/ukT= 0207 949 0307serv ce.eu@v ewson ceurope.com Europe, M ddle East, Balt c countr es, and North Afr ca www.v ewson ceurope.comContact your resellerserv ce.eu@v ewson ceurope.com Austral a and New Zealand www.v ewson c.com.au/ support/ AUS= 1800 880 818 NZ= 0800 008 822serv [email protected] ewson c.com S ngapore/ Malays a/ Tha land www.v ewson c.com.sg/ support/ T= 65 64616044 serv [email protected] ewson c.com South Afr ca/Other countr es www.v ewson c.com T= 886 2 2246-3456 F= 886 2 2249-1751serv [email protected] ewson c.com Hong Kong www.hk.v ewson c.com/ support/ T= 852 3102 2900 serv [email protected] ewson c.com Macauwww.hk.v ewson c.com/support/T= 853 700 303 serv [email protected] ewson c.com Korea www.v ewson c.comT= 080 265 9080serv [email protected] ewson c.com
ViewSonic PJ556D33 Limited Warranty VIEWSONIC® PROJECTOR What the warranty covers: V ewSon c warrants ts products to be free from defects n mater al and workmansh p, under normal use, dur ng the warranty per od. If a product proves to be defect ve n mater al or workmansh p dur ng the warranty per od, V ewSon c w ll, at ts sole opt on, repa r or replace the product w th a l ke product. Replacement product or parts may nclude remanufactured or refurb shed parts or components. How long the warranty is effective: North and South Amer ca: 3 years for all parts exclud ng the lamp, 3 years for labor, 1 year for the original lamp from the date of the first consumer purchase. Europe: 3 years for all parts exclud ng the lamp, 3 years for labor, 1 year for the or g nal lamp from the date of the first consumer purchase. Other reg ons or countr es: Please check with your local dealer or local ViewSonic office for the warranty nformat on. Lamp warranty subject to terms and cond t ons, ver f cat on and approval. Appl es to manufacturer’s nstalled lamp only. All accessory lamps purchased separately are warranted for 90 days. Who the warranty protects: This warranty is valid only for the first consumer purchaser. What the warranty does not cover: 1. Any product on which the serial number has been defaced, modified or removed. 2. Damage, deter orat on or malfunct on result ng from: a. A c c d e n t , m s u s e , n e g l e c t , f r e , w a t e r, l g h t n n g , o r o t h e r a c t s o f n a t u r e , unauthorized product modification, or failure to follow instructions supplied with the product. b. Repa r or attempted repa r by anyone not author zed by V ewSon c. c. Any damage of the product due to sh pment. d. Removal or nstallat on of the product. e. Causes external to the product, such as electric power fluctuations or failure. f. Use of supplies or parts not meeting ViewSonic’s specifications. g. Normal wear and tear. h. Any other cause wh ch does not relate to a product defect. 3. Any product exh b t ng a cond t on commonly known as “ mage bu lt- n” wh ch results when a stat c mage s d splayed on the product for an extended per od of t me. 4. Removal, nstallat on, and set-up serv ce charges. How to get service: 1. For nformat on about rece v ng serv ce under warranty, contact V ewSon c Customer Support (Please refer to Customer Support page). You w ll need to prov de your product’s ser al number.
34ViewSonic PJ556D 2. To obta n warranted serv ce, you w ll be requ red to prov de (a) the or g nal dated sales sl p, (b) your name, (c) your address, (d) a descr pt on of the problem, and (e) the ser al number of the product. 3. Take or sh p the product fre ght prepa d n the or g nal conta ner to an author zed V ewSon c serv ce center or V ewSon c. 4. For add t onal nformat on or the name of the nearest V ewSon c serv ce center, contact V ewSon c. Limitation of implied warranties: There are no warrant es, express or mpl ed, wh ch extend beyond the descr pt on conta ned here n nclud ng the mpl ed warranty of merchantab l ty and f tness for a part cular purpose. Exclusion of damages: V ewSon c’s l ab l ty s l m ted to the cost of repa r or replacement of the product. V ewSon c shall not be l able for: 1. Damage to other property caused by any defects n the product, damaged based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of bus ness opportun ty, loss of goodw ll, nterference w th bus ness relat onsh ps, or other commerc l loss, even f adv sed of the poss b l ty of such damages. 2. Any other damages, whether nc dental, consequent al or otherw se. 3. Any cla m aga nst the customer by other party. Effect of state law: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow l m tat ons on mpl ed warrant es and/or do not allow the exclus on of nc dental or consequent al damages, so the above l m tat ons and exclus ons may not apply to you. Sales outside the U.S.A. and Canada: For warranty nformat on and serv ce on V ewSon c products sold outs de of the U.S.A. and Canada, contact V ewSon c or your local V ewSon c dealer. The warranty per od for th s product n ma nland Ch na (Hong Kong, Macao and Ta wan Excluded) s subject to the terms and cond t ons of the Ma ntenance Guarantee Card. 4.3: Projector Warranty PRJ_LW01 Rev. 1g 06-30-06