ViewSonic Projector PJ551D User Manual
Here you can view all the pages of manual ViewSonic Projector PJ551D User Manual. The ViewSonic manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 21
ViewSonic 15 PJ551D How to operate 1. Press the Menu button to open the OSD menu. 2. When OSD is displayed, use S / T to select any feature in the main menu. 3.After selecting the desired main menu feature, press X to enter sub-menu for feature setting. 4.Adjust the settings with W / X. 5. Press the Menu button, the screen will return to the main menu. 6. To exit OSD, Press the Menu button again. The OSD menu...
Page 22
ViewSonic 16 PJ551D Computer Image (Computer Mode) Frequency Adjust the timing of the projector relative to the computer. Tracking Adjust the phase of the projector relative to the computer. H Position (Horizontal Position) Adjust the image left or right within the projection area. V Position (Vertical Position) Adjust the image up or down within the projection area. Video Image (Video Mode) Color Adjust the...
Page 23
ViewSonic 17 PJ551D ECO Mode Use this function to dim the projector lamp light output which will lower power consumption and increase lamp life. Altitude Turning on Highland mode operates the fans at full speed continuously to allow for proper high altitude cooling of the projector. OSD Timeout Duration OSD menu stays active (at idle state by second). Option (Computer / Video Mode) Blank Screen Blank the screen...
Page 24
ViewSonic 18 PJ551D Maintenance The projector needs proper maintenance. You should keep the lens clean as dust, dirt or spots will project on the screen and diminish image quality. If any other parts need replacing, contact your dealer or qualified service personnel. When cleaning any part of the projector, always switch off and unplug the projector first. Warning: Never open any of the covers on the projector....
Page 25
ViewSonic 19 PJ551D Replacing the Lamp As the projector operates over time, the brightness of the projector lamp gradually decreases and the lamp becomes more susceptible to breakage. We recommend replacing the lamp if a warning message is displayed. Do not attempt to replace the lamp yourself. Contact the qualified service personnel for replacement. „The lamp becomes high temperature after turning off the...
Page 26
ViewSonic 20 PJ551D 1. Turn off the projector. 2. If the projector is installed in a ceiling mount, remove it from the mount. 3. Unplug the power cord. 4. Loosen the screw in the side of the lamp cover and remove the cover. 5. Remove the screws from the lamp module, raise the handle, and lift out the module. 6. Insert the new lamp module into the projector and tighten the screws. 7. Replace the lamp cover and...
Page 27
ViewSonic 21 PJ551D Specifications Display Type Single 0.55 DLP panel Resolution (Pixels) XGA (1024 × 768) Lens Manual Zoom (1.1x) Contrast Ratio 2000:1 Screen Size 27.8” – 255” Lamp 180W Input / Output Source D-Sub 15 pin, S-video, composite video, USB Video Compatibility NTSC 3.58, NTSC4.43 PA L - 6 0 , M , N SECAM, HDTV (480i/p, 576i/p, 720p, 1080i) Scanning Frequency Horizontal Freq. Vertical Freq.31 - 79...
Page 28
ViewSonic 22 PJ551D Appendix LED Indicator Messages LED TypeColorStatusMeaning LAMP LED TEMP LEDGreen OffFlash -The projector is in standby mode. LAMP LED TEMP LEDGreen GreenSolid FlashThe projector system has some problems with its fan, so the projector cannot start up. LAMP LED TEMP LEDGreen GreenSolid SolidThe lamp is in good condition and is projecting at maximum brightness. LAMP LED TEMP LEDAmber...
Page 29
ViewSonic 23 PJ551D Compatibility Modes Computer: Video: CompatibilityResolutionH-Sync [KHz]V-S y nc [Hz] VGA 640 x 480 31.5 59.9 37.9 72.8 37.5 75.0 43.3 85.0 SVGA 800 x 600 35.2 56.3 37.9 60.3 48.1 72.2 46.9 75.0 53.7 85.1 XGA 1024 x 768 48.4 60.0 56.5 70.1 60.0 75.0 68.7 85.0 SXGA 1152 x 864 64.0 70.0 67.5 75.0 1280 x 960 60.0 60.0 75.0 75.0 1280 x 1024 64.0 60.0 WXGA 1280 x 768 47.8 60.0 60.3 74.9 68.6...
Page 30
ViewSonic 24 PJ551D Troubleshooting Refer to the symptoms and measures listed below before sending the projector forrepairs. If the problem persists, contact your local reseller or service center. Please refer to Indicator Messages as well. Start-up problems If no lights turn on: „Be sure that the power cord is securely connected to the projector and the other endis plugged into an outlet with power. „Press the...