ViewSonic Projector PJ513D/PJ513DB User Manual

							ViewSonic                                                35                                                PJ513D/PJ513DB 
SYSTEM SETUP: Advanced menu
FUNCTION
(default setting / 
value)DESCRIPTION
Quick Cooling
(On)
Enables or disables the Quick Cooling function. Selecting On enables 
the function and projector cooling time will be shortened from a 
normal 90-second duration to approximately 30 seconds.
High Altitude 
Mode
(Off)A mode for operation in high altitude areas. See Operating in a high 
altitude environment on page 26 for details.
DCR
(Off)Enables or disables the DCR (Dynamic Contrast Ratio) function. 
Selecting On enables the function and the projector will 
automatically switch the lamp mode between normal and economic 
mode according to the input image detected.
This function is only available when a PC source is in use.
After enabling DCR, frequent lamp mode switching may shorten lamp 
life and noise level will vary during operation.
Audio 
SettingsMute (Off)
Vo l u m e (5)
See Adjusting the sound on page 27 for details.
Menu SettingsMenu Display Time (15 sec)
Sets the length of time the OSD will remain active after your last 
button press. The range is from 5 to 30 seconds in 5-second 
increments.
Menu Position (Center)
Sets the On-Screen Display (OSD) menu position.
Lamp 
Settings
Lamp Mode (Normal)
Setting the projector in Economic mode also extends the lamp timer 
automatic shutdown feature. See Setting Lamp Mode as Economic 
on page 38 for details.
Reset Lamp Timer
Once the lamp is renewed, select Reset to return the lamp timer to 0. 
See Resetting the lamp timer on page 41 for details.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used. See Getting to 
know the lamp hour on page 38 for details on how the total lamp 
hour is calculated.
Reset All 
SettingsReturns all settings to the factory preset values.
The following settings will still remain: Projector Position, Language, 
High Altitude Mode, Phase, User 1, User 2, Position, H. Size. 
						

							ViewSonic                                                36                                                PJ513D/PJ513DB
INFORMATION menu
This menu shows you the current operating status of the projector.
Some picture adjustments are available only when certain input sources are in use. 
Unavailable adjustments are not shown on the screen.
FUNCTIONDESCRIPTION
Current System 
Status
Source
Shows the current signal source.
Preset mode
Shows the selected mode in the PICTURE menu.
Resolution
Shows the native resolution of the input signal.
Color system
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent lamp hour
Displays the number of hours the lamp has been used. 
						

							ViewSonic                                                37                                                PJ513D/PJ513DB 
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular 
basis is to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts 
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. 
• Use a canister of compressed air to remove dust. 
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens 
cleaner and gently wipe the lens surface.
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure 
as described in Shutting down the projector on page 28 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH 
detergent. Then wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the 
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions 
below:
• Make sure the temperature and humidity of the storage area are within the 
recommended range for the projector. Please refer to Specifications on page 45 or 
consult your dealer about the range.
• Retract the adjuster feet.
• Remove the batteries from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. 
						

							ViewSonic                                                38                                                PJ513D/PJ513DB
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is 
automatically calculated by the built-in timer. The method of calculating the equivalent 
lamp hour is as follows:
Total (equivalent) lamp hour
= 1 (hours used in Economic mode) + 3/2 (hours used in normal mode)
See Setting Lamp Mode as Economic below for more information on Economic mode.
The lamp hour in Economic mode is calculated as 2/3 of that in normal mode. That is, 
using the projector in Economic mode helps to extend the lamp hour by 1/2.
Extending lamp life
The projection lamp is a consumable item that normally can last up to 2000-3000 hours 
with proper usage. To keep the lamp life as long as possible, you can do the following 
settings via the OSD menu.
• Setting Lamp Mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If the 
Economic mode is selected, the light output will be reduced and result in darker 
projected pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set 
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > 
Lamp Mode menu and press  / .
When the DCR function is set to On, the lamp mode cannot be adjusted.
• Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is 
detected after a set period of time to prevent unnecessary waste of lamp life.
To  s e t  Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off 
menu and press  / . The time period can be set from 5 to 30 minutes in 5-minute 
increments. If the preset time lengths are not suitable for your presentation, select 
Disable. The projector will not automatically shut down in a certain time period. 
						

							ViewSonic                                                39                                                PJ513D/PJ513DB 
Warning message
When the Lamp indicator lights up red or a message appears suggesting it is time to 
replace the lamp, please install a new lamp or consult your dealer. An old lamp may 
cause a malfunction in the projector and in some instances the lamp may explode.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too 
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator 
still lights up after turning the power back on, please contact your dealer. See Indicators on 
page 42 for details.
The following Lamp warning displays will remind you to change the lamp.
MessageStatus
The lamp has been in operation for 2000 hours. 
Install a new lamp for optimal performance. If 
the projector is normally run with Economic 
Mode selected (See Lamp Mode (Normal) 
on page 35), you may continue to operate the 
projector until the 2950 hour lamp warning 
appears. 
The lamp has been in operation for 2950 hours. 
A new lamp should be fitted to avoid the 
inconvenience when the projector runs out of 
lamp time.
The lamp has been in operation for 3000 hours. 
It is strongly recommended that you replace the 
lamp at this age. The lamp is a consumable 
item. The lamp brightness diminishes with use. 
This is normal lamp behavior. You can replace 
the lamp whenever you notice that the 
brightness level has significantly diminished. If 
the lamp is not replaced beforehand, it must be 
replaced after 3000 hours usage.
The lamp MUST be replaced before the 
projector will operate normally.
OK
Order Replacement Lamp
Lamp > 2000 Hours
Notice
OK
Replace Lamp Soon 
Lamp > 2950 Hours
Notice
OK
Replace Lamp Now 
Lamp > 3000 Hours
Lamp usage time exceeded
Notice
OK
Out of Lamp-Usage Time
Replace lamp (refer to User manual)
Then reset lamp timer
Notice 
						

							ViewSonic                                                40                                                PJ513D/PJ513DB
Replacing the lamp
• To reduce the risk of electrical shock, always turn the projector off and disconnect the 
power cord before changing the lamp.   
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes 
before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution 
when removing lamp glass that has shattered into sharp pieces.
• To reduce the risk of injuries to fingers and/or compromising picture quality by touching 
the lens, do not touch the empty lamp compartment when the lamp is removed.
• This lamp contains mercury. Consult your local hazardous waste regulations to dispose 
of this lamp in a proper manner.
1. Turn the power off and disconnect 
the projector from the wall socket. If 
the lamp is hot, avoid burns by 
waiting for approximately 45 
minutes until the lamp has cooled.
2. Turn the projector over. Then loosen 
the screws on the lamp cover.
3. Remove the lamp cover from the 
projector.
Do not turn the power on with the 
lamp cover removed.
4. Remove the lamp cords from the slots.5. Disconnect the lamp connector by 
pushing it against the projector while 
pulling it up.
6. Loosen the screw that secures the 
lamp.
7. Lift the handle so that it stands up. 
Use the handle to slowly pull the lamp 
out of the projector.Pulling it too quickly may cause the 
lamp to break and scatter broken 
glass in the projector.
Do not place the lamp in locations 
where water might splash on it, 
children can reach it, or near 
flammable materials.
Do not insert your hands into the 
projector after the lamp is removed. If 
you touch the optical components 
inside, it could cause color 
unevenness and distortion of the 
projected pictures. 
						

							ViewSonic                                                41                                                PJ513D/PJ513DB  8. As shown in the figure, hold the new 
lamp first and align the lamp with the 
compartment in the projector, and 
then insert the lamp all the way into 
the projector.
9. Tighten the screw that secures the 
lamp.
Loose screw may cause a bad 
connection, which could result in 
malfunction.
Do not over tighten the screw.
10. Connect the lamp connector to the 
projector.
11. Place the lamp cords back to the slots.
12. Replace the lamp cover on the 
projector.13. Tighten the screws that secure the 
lamp cover.
Loose screw may cause a bad 
connection, which could result in 
malfunction.
Do not over tighten the screws.
14. Restart the projector.
Do not turn the power on with the 
lamp cover removed. 
15. Resetting the lamp timer
Do not reset if the lamp is not 
replaced as this could cause damage. 
i. Go to the SYSTEM SETUP: 
Advanced > Lamp Settings 
menu. Press MODE/ENTER. 
ii. The Lamp Settings page 
displays. Highlight Reset Lamp 
Timer. 
iii. A warning message displays 
asking if you want to reset the 
lamp timer. Highlight Reset and 
press MODE/ENTER. The lamp 
time will be reset to 0.
Reset lamp timer?
Reset
Cancel
Notice 
						

							ViewSonic                                                42                                                PJ513D/PJ513DB
Temperature information
When the Temperature warning light is on, it is warning you of the following possible 
problems:
1. The internal temperature is too high.
2. The fans are not working.
Turn the projector off and contact qualified service personnel for further help. For 
more detailed information, please refer to Indicators on page 42.
Indicators
Illustration
•Blank -: Light OFF
•O: Orange light
• : Light flashing•R: Red light
•: Light ON•G: Green light
LightStatus & Description
PowerTe m pLamp
Power events
The projector has just been connected to a power outlet.
--Stand-by mode.
--Powering up.
--Normal operation.
--
1. The projector needs 90 seconds to cool down as it was 
abnormally shut down without the normal cooling down 
process. Or
2. The projector needs to cool for 90 seconds after the 
power is turned off.
--The projector has shutdown automatically. If you try to re-start 
the projector, it will shutdown again. Please contact your 
dealer for assistance.
Lamp events
-The projector has shutdown automatically. If you try to re-start 
the projector, it will shutdown again. Please contact your 
dealer for assistance.
--1. The projector needs 90 seconds to cool down. Or
2. Please contact your dealer for assistance.
 
  
O O O 
O 
 G 
 G 
O 
O 
O  R 
 R  
						

							ViewSonic                                                43                                                PJ513D/PJ513DB 
LightStatus & Description
PowerTe m pLamp
Thermal events
--
The projector has shutdown automatically. If you try to re-start 
the projector, it will shutdown again. Please contact your 
dealer for assistance.
-
-
-
-
 R 
 R  R 
 R  G 
 R O 
 R  R  R 
 R  R  G 
 R  R O 
 G  R  R 
 G  R  G 
 G  R O 
O  R  R 
O  R  G 
O  R O 
 G  R 
 G  G  
						

							ViewSonic                                                44                                                PJ513D/PJ513DB
Troubleshooting
The projector does not turn on.
No picture
Blurred image
Remote control does not work
CauseRemedy
There is no power from the power 
cable.Plug the power cord into the AC inlet on the 
projector, and plug the power cord into the 
power outlet. If the power outlet has a switch, 
make sure that it is switched on.
Attempting to turn the projector on 
again during the cooling process.Wait until the cooling down process has 
completed.
CauseRemedy
The video source is not turned on or 
connected correctly.Turn the video source on and check that the 
signal cable is connected correctly.
The projector is not correctly 
connected to the input source device.Check the connection.
The input signal has not been 
correctly selected.Select the correct input signal with the Source 
key on the projector or remote control.
The lens cover is still closed. Open the lens cover.
CauseRemedy
The projection lens is not correctly 
focused.Adjust the focus of the lens using the focus 
ring.
The projector and the screen are not 
aligned properly.Adjust the projection angle and direction as 
well as the height of the unit if necessary.
The lens cover is still closed. Open the lens cover.
CauseRemedy
The batteries are out of power. Replace the batteries with new ones.
There is an obstacle between the 
remote control and the projector.Remove the obstacle.
You are too far away from the 
projector.Stand within 8 meters (26 feet) of the 
projector.