ViewSonic Projector Pj260d User Manual

							ViewSonic 5 PJ260D
Using the Product
Control Panel
LED
Button Function
Lamp LED indicator
Refer to “LED Indicator Messages”.
Power LED indicator
Refer to “LED Indicator Messages”. 
MENU
Display or exit the on screen display menus.
Turn the projector on or off.
SOURCE
Manually select an input source.
Keystone
Correct the keystone distortion.
Four directional buttons
Use four directional buttons to select items or make adjustments to your selection.
RESYNC
Resynchronize the projector to the input signal from a computer. This function is 
available for computer mode only.
76
21
34
5
8
1
2
3
4
5
6
7
8 
						

							ViewSonic 6 PJ260D
Connection Ports
SERVICE
Firmware update.
COMPUTER IN
Input analog RGB signal from a computer or other source, or a component video 
signal (Y/P
B/PR) from video equipment.
S-VIDEO
Input S-video signals from video equipment.
VIDEO
Input video signals from video equipment.
AUDIO IN
Input audio signals.
12345
1
2
3
4
5 
						

							
ViewSonic 7 PJ260D
Remote Control
Power
Turn the projector on or off.
Four directional buttons
Use four directional buttons to select 
items or make adjustments to your 
selection.
MENU
Display or exit the on-screen display 
menus.
Laser
Aim the remote at the viewing screen, 
press and hold this button to activate 
the laser pointer.
Keystone + / -
Correct the keystone distortion.
Mute
Cut off the sound temporarily. Press 
again to cancel the Mute function.
Resync
Resynchronize the projector to the 
input signal from a computer. This 
function is available for computer 
mode only.
Blank Screen
Cut off the screen temporarily. Press 
again to cancel the Blank Screen 
function.
ViewMatch
Switch the white peaking.
Source
Manually select an input source.
Volume + / -
Adjust the volume level.
Freeze
Press Freeze to pause the screen 
image. Press again to cancel the 
Freeze function.
1
2
3
4
5
6
7
8
9
10
11
12 
						

							ViewSonic 8 PJ260D
Installing the Batteries
1. Open the battery cover in the 
direction shown.
2. Install batteries as indicated by the 
diagram inside the compartment.
3. Close the battery cover into 
position.
„Keep the batteries out of the reach of children. There is a danger of death 
by accidentally swallowing the batteries.
„Remove batteries from remote control when not using for extended periods.
„Do not dispose of the used batteries along with household waste. Dispose 
of used batteries according to local regulations.
„Danger of explosion may happen if batteries are incorrectly replaced. 
Replce all the batteries with new ones. 
						

							ViewSonic 9 PJ260D
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
„Operating the projector from 
the front
„Operating the projector from 
the rear
„Do not point the laser directly to the peoples eyes (especially small children). 
There is a danger of injury to the eyes.
„The remote control may not operate when there is sunlight or other strong 
light such as a fluorescent lamp shining on the remote sensor.
„Operate the remote control from a position where the remote sensor is visible.„Do not drop the remote control or jolt it.„Keep the remote control out of locations with excessively high temperature or 
humidity.
„Do not get water on the remote control or place wet objects on it.„Do not disassemble the remote control. 
						

							ViewSonic 10 PJ260D
Installation
Connecting the Projector
USB Cable VGA (D-SUB) to HDTV (RCA) Cable
VGA Cable (D-Sub to D-Sub) S-Video Cable
Audio Cable Composite Video Cable14
25
36
„When connecting cable, power cords of both a projector and external 
equipment should be disconnected from AC outlet.„The figure above is a sample connection. This does not mean that all of these 
devices can or must be connected simultaneously.
„The cables that come with the projector may differ from the above illustration. 
The included cables are based on actual shipment delivery. 
						

							ViewSonic 11 PJ260D
Powering On/Off the Projector
Powering On the Projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press   button to turn on the projector.
The projector takes a minute or so to warm up. 
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically 
detects your source.
„If you are connecting multiple sources to the projector simultaneously, press 
the SOURCE button on the control panel or the Source button on the remote 
control.
Warning:
„Remove the lens cap first before powering on.
„Never look into the lens when the lamp is on. This can damage your eyes. It 
is especially important that children are not allowed to look into the lens.
Powering Off the Projector:
1. Press   button to turn off the projector lamp. You will see a message Power off? 
Press Power again appear on the screen.  
2. Press   button again to confirm.
„The cooling fans continue to operate for cooling cycle and the Lamp LED will 
keep flashing.
„When the Power LED begins flashing, the projector has entered stand-by 
mode.
„If you want to turn the projector back on, you must wait until the projector has 
completed the cooling cycle and has entered stand-by mode. Once in 
stand-by mode, simply press   button to restart the projector.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector immediately following a power off procedure. 
						

							ViewSonic 12 PJ260D
Adjusting the Projector
Adjusting the Projector Height
The projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image:
1. To raise or lower the image, press the elevator button and raise or lower the front 
of the projector. Release the button to lock the adjustment.
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.
Adjusting the Projector Zoom and Focus
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.2. Adjust the image by sliding the zoom ring. 
Tilt-adjustment foot
Elevator button
Elevator foot
„To avoid damaging the projector, make sure that the elevator foot and 
tilt-adjustment foot are fully retracted before placing the projector in its 
carrying case.
Focus ringZoom ring 
						

							ViewSonic 13 PJ260D
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
Projection Distance
 (meters)Screen Size (for 4:3 aspect ratio diagonal length)
Wide (inches) Tele (inches)
1.6 40.7 34.6
2 50.8 43.2
3 75.3 64.1
5 125.2 106.7
10 250 213.0
12 300 255.5
„Position the projector in a horizontal position; other positions can cause heat 
build-up and damage to the projector.
„Make sure the heat ventilation holes are not blocked.„Do not use the projector in a smoky environment. Smoke residue may 
cause build-up on critical parts (i.e. DMD, lens assembly, etc.) 
						

							ViewSonic 14 PJ260D
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image 
adjustments and change a variety of settings.