ViewSonic Projector Pj1173 User Manual

							
PJ1173ViewSonic76

Configuring and controlling the projector via a web browser (continued)
Mail Settings
Management with Web browser software
Displays and configures e-mail addressing settings.
ItemDescription
Send mailClick [Enable] check box to use the e-mail function. Configure the conditions for sending e-mail under the Alert Settings.
SMTP Server IP Address
Configures the address of the mail server in IP format.• The address allows not only IP address but also domain name if the valid DNS server is setup in the Network Settings. The maximum length of host or domain name is up to 55 characters.
Sender E-mail addressConfigures the sender e-mail address. The length of the sender e-mail address can be up to 255 
alphanumeric characters.
Recipient E-mail address
Configures the e-mail address of up to five recipients. You can also specify [TO] or [CC] for each address. The length of the recipient e-mail address can be up to 255 alphanumeric characters.
Click [Apply] button to save the settings.
• You can confirm whether the mail settings work correctly using [Send 
Test Mail] button. Please enable Send mail setting before clicking [Send Test 
Mail]. 
• If you connect the projector to an existing network, consult a network 
administrator before setting server addresses.
NOTE 
						

							
PJ1173ViewSonic77

Configuring and controlling the projector via a web browser (continued)
Alert Settings
Displays and configures failure & alert settings.
Alert ItemDescription
Cover ErrorThe lamp cover has not been properly fixed.
Fan ErrorThe cooling fan is not operating.
Lamp ErrorThe lamp does not light, and there is a possibility that interior portion has become heated.
Temp ErrorThere is a possibility that the interior portion has become heated.
Air Flow ErrorThe internal temperature is rising.
Lamp Time ErrorLamp time over.
Cold ErrorThere is a possibility that the interior portion has become overcooled.
Filter ErrorFilter time over.
Other ErrorOther error.If displaying this error, please contact ViewSonic.
Schedule Execution ErrorSchedule Execution error.
Lamp Time AlarmLamp time over Alarm Time setting.
Filter Time AlarmFilter time over Alarm Time setting.
Transition Detector AlarmTransition Detector Alarm.
“CHANGE THE LAMP” is displayed.“CHANGE THE LAMP” is displayed.
Cold StartThe Power switch is turned on.(Off → standby mode)
Authentication FailureThe SNMP access is detected from the invalid SNMP 
community.
Refer to “Troubleshooting” in the User’s Manual (detailed) – Operating Guide for 
further detailed explanation of Error except Other Error and Schedule Ex\
ecution Error.
Management with Web browser software 
						

							
PJ1173ViewSonic78

Configuring and controlling the projector via a web browser (continued)
Management with Web browser software
The Alert Items are shown below.
Setting ItemDescription
Alarm TimeConfigures the time to alert.(Only Lamp Time Alarm and Filter Time Alarm.)
SNMP TrapClick [Enable] check box to enable SNMP Trap alerts.
Send MailClick [Enable] check box to enable e-mail alerts.(Except Cold Start and Authentication Failure.)
Mail Subject
Configures the subject line of the e-mail to be sent. The length of the subject line can be up to 55 alphanumeric characters.(Except Cold Start and Authentication Failure.)
Mail Text
Configures the text of the e-mail to be sent. The length of the text can be up to 04 alphanumeric characters.(Except Cold Start and Authentication Failure.)
Click [Apply] button to save the settings.
• The trigger of Filter Error e-mail is depending on the FILTER 
MESSAGE setting in the SERVICE item of the OPTION menu which defines 
the period until the filter message is displayed on the projector screen. The 
e-mail will be sent when the filter timer exceeds 50, 100, 200, 300, 400, 500, 
600, 700 or 800 hours based on the configuration. No notification e-mail will be 
sent if the FILTER MESSAGE is set to TURN OFF.
• Lamp Time Alarm is defined as a threshold for e-mail notification (reminder) of 
the lamp timer. When the lamp hour exceeds this threshold that is configured 
through the Web page, the e-mail will be sent out.
• Filter Time Alarm is defined as a threshold for e-mail notification (reminder) 
of the filter timer. When the filter hour exceeds this threshold, the e-mail will be 
sent out.
NOTE 
						

							
PJ1173ViewSonic79

Configuring and controlling the projector via a web browser (continued)
Schedule Settings
Displays and configures schedule settings.
ItemDescription
DailyConfigures the daily schedule.
SundayConfigures the Sunday schedule.
MondayConfigures the Monday schedule.
TuesdayConfigures the Tuesday schedule.
WednesdayConfigures the Wednesday schedule.
ThursdayConfigures the Thursday schedule.
FridayConfigures the Friday schedule.
SaturdayConfigures the Saturday schedule.
Specific date No.1Configures the specific date (No.1) schedule.
Specific date No.2Configures the specific date (No.2) schedule.
Specific date No.3Configures the specific date (No.3) schedule.
Specific date No.4Configures the specific date (No.4) schedule.
Specific date No.5Configures the specific date (No.5) schedule.
Management with Web browser software 
						

							
PJ1173ViewSonic80

Configuring and controlling the projector via a web browser (continued)
Management with Web browser software
The daily and weekly event items are shown below.
ItemDaily & Weekly Description
ScheduleClick [Enable] check box to enable the schedule.
Schedule ListDisplays the current schedule.
The specific date event items are shown below. 
ItemSpecific date (No.1-5) Description
ScheduleClick [Enable] check box to enable specific date (No.1-5) schedule.
Date (Month/Day)Configures the month and date.
Schedule ListDisplays the current specific date (No.1-5) schedule.
Click [Apply] button to save the settings.
To add additional functions and events, click [Add] button and set the following 
items.
ItemDescription
TimeConfigures the time to execute commands.
Command[Parameter]Configures the commands to be executed.
Power Configures the parameters for power control.
Input Source Configures the parameters for input switching.
Display Image Configures the parameters for display of transfer image data.
Click [Register] button to add new commands to the Schedule List.
Click [Delete] button to delete commands from the Schedule List.
Click [Reset] button to delete all commands from the Schedule List.
• After the projector is moved, check the date and time set for the 
projector before configuring the schedules. Strong shock may make the date 
and time settings get out of tune.
NOTE 
						

							
PJ1173ViewSonic8

Management with Web browser software
Configuring and controlling the projector via a web browser (continued)
Date/Time Settings
Displays and configures the date and time settings.
ItemDescription
Current DateConfigures the current date in year/month/day format.
Current TimeConfigures the current time in hour:minute:second format.
Daylight Savings TimeClick [ON] check box to enable daylight savings time and set the following items.
StartConfigures the date and time daylight savings time begins.
MonthConfigures the month daylight savings time begins (1~12).
WeekConfigures the week of the month daylight savings time begins (First, 2, 3, 4, Last).
DayConfigures the day of the week daylight savings time begins (Sun, Mon, Tue, Wed, Thu, Fri, Sat).
TimehourConfigures the hour daylight savings time begins (0 ~ 23).
minuteConfigures the minute daylight savings time begins (0 ~ 59).
EndConfigures the date and time daylight savings time ends.
MonthConfigures the month daylight savings time ends (1 ~ 12).
WeekConfigures the week of the month daylight savings time ends (First, 2, 3, 4, Last).
DayConfigures the day of the week daylight savings time ends (Sun, Mon, Tue, Wed, Thu, Fri, Sat).
TimehourConfigures the hour daylight savings time ends (0 ~ 23).
minuteConfigures the minute daylight savings time ends (0 ~ 59). 
						

							
PJ1173ViewSonic8

Configuring and controlling the projector via a web browser (continued)
Management with Web browser software
ItemDescription
Time differenceConfigures the time difference. Set the same time difference as the one set on your PC. If unsure, consult your IT manager.
SNTPClick the [ON] check box to retrieve Date and Time information from the SNTP server and set the following items.
SNTP Server IP Address
Configures the SNTP server address in IP format.• The address allows not only IP address but also domain name if the valid DNS server is setup in the Network Settings. The maximum length of host or domain name is up to 55 characters.
CycleConfigures the interval at which to retrieve Date and Time information from the SNTP server (hours:minutes).
Click [Apply] button to save the settings.
• The new configuration settings are activated after restarting the 
network connection. When the configuration settings are changed, you must 
restart the network connection. You can restart the network connection by 
clicking [Network Restart] on the main menu.
• If you connect the projector to an existing network, consult a network 
administrator before setting server addresses.
• To enable the SNTP function, the time difference must be set. 
• The projector will retrieve Date and Time information from the time server and 
override time settings when SNTP is enabled.
• The internal clock’s time may not remain accurate. Using SNTP is 
recommended to maintain accurate time.
NOTE 
						

							
PJ1173ViewSonic83

Management with Web browser software
Configuring and controlling the projector via a web browser (continued)
Security Settings
Displays and configures passwords and other security settings.
ItemDescription
Administrator authorityConfigures the Administrator ID and password.
Administrator IDConfigures the Administrator ID. The length of the text can be up to 3 alphanumeric characters. 
Administrator Password
Configures the Administrator password. The length of the text can be up to 55 alphanumeric characters. 
Re-enter Administrator 
Password
Reenter the above password for verification.
User authorityConfigures the User ID and password.
User IDConfigures the User ID. The length of the text can be up to 3 alphanumeric characters. 
User PasswordConfigures the User password. The length of the text can be up to 55 alphanumeric characters. 
Re-enter User PasswordReenter the above password for verification. 
						

							
PJ1173ViewSonic84

Configuring and controlling the projector via a web browser (continued)
Management with Web browser software
Click [Apply] button to save the settings.
• The new configuration settings are activated after restarting the 
network connection. When the configuration settings are changed, you must 
restart the network connection. You can restart the network connection by 
clicking [Network Restart] on the main menu.
• Only numbers ‘0-9’ and alphabet ‘a-z’, ‘A-Z’ can be used.
NOTE
ItemDescription
Network ControlConfigures the Authentication password for the command control.
Authentication PasswordConfigures the Authentication password. The length of the text can be up to 3 alphanumeric characters.
Re-enter Authentication PasswordReenter the above password for verification.
SNMPConfigures the community name if SNMP is used.
Community nameConfigures the community name. The length of the text can be up to 64 alphanumeric characters. 
						

							
PJ1173ViewSonic85

Management with Web browser software
Configuring and controlling the projector via a web browser (continued)
Projector Control
Controls the projector.
ItemDescription
Main
PowerTurns the power on/off.
Input SourceSelects the input source.
Picture ModeSelects the picture mode setting.
Blank On/OffTurns Blank on/off.
MuteTurns Mute on/off.
FreezeTurns Freeze on/off.
Magnify
Controls the magnify setting. In some input signal sources, it might stop “Magnify” even though it does not reach to maximum setting value.The variable range:• For a RGB or HDMI signal  0-48• For a video, component or s-video signal  0-16
Picture
BrightnessAdjusts the brightness setting.
ContrastAdjusts the contrast setting.
GammaSelects the gamma setting.
Color TempSelects the color temperature setting.
ColorAdjusts the color setting.
TintAdjusts the tint setting.
SharpnessAdjusts the sharpness setting.
Active IrisSelects the active iris setting.
MyMemory SaveSaves the MyMemory data.
MyMemory RecallRecalls the MyMemory data.
The items shown in the table below can be 
performed using the Projector Control menu. 
Select an item using the up and down arrow keys 
on the PC.
Most of the items have a submenu. Refer to the 
table below for details.
• The setting value may not match with the actual value if the user 
changes the value manually. In that case, please refresh the page by clicking 
[Refresh] button.
NOTE