ViewSonic Projector Pj1172 User Manual

ViewSonic  PJ1172 26
INPUT Menu(Continued)
Item Description
P.IN P. INPUT Select a signal input port for the child window using the S/T buttons.: 
    VIDEO  S-VIDEO
memo About the child window, please refer to the section “Displaying the 
Child Window”.
P.IN P. POSIT. Select the display position of the child window using the S/T 
buttons.:
    
memo About the child window, please refer to the section “Displaying the 
Child Window”.
POWERUP 
INPUTSelect a signal input port to display just when the...

ViewSonic  PJ1172 27
AUTO Menu
With the AUTO menu, the items shown in the table below can be 
performed. Perform each operation in accordance with the 
instructions in the table below.
(This table is continued to the following page.) Item Description
ADJUST Pressing the X (or the ENTER) button performs the automatic 
adjustment.

ViewSonic  PJ1172 28
AUTO Menu (continued)
Item Description
SEARCH Select TURN ON or TURN OFF using the S/T buttons.:
    TURN ON  TURN OFF
When TURN ON is selected, detecting no signal cycles through input 
ports and displays the picture of retrieved signal.
      M1-D   

ViewSonic  PJ1172 29
SCREEN Menu
With the SCREEN menu, the items shown in the table below can 
be performed. Perform each operation in accordance with the 
instructions in the table below.
(This table is continued to the following page.) Item Description
BLANK Select a type of BLANK screen using the S/T buttons.:
     MyScreen  ORIGINAL  BLUE  WHITE  BLACK
The BLANK screen is displayed by pressing a button.
The MyScreen is the screen you can register a desired screen, and 
the ORIGINAL is the...

ViewSonic  PJ1172 30
AUTO Menu (continued)
How to register your picture as the MyScreen
  Item Description
MESSAGE Select TURN ON or TURN OFF using the S/T buttons.:
    TURN ON  TURN OFF
When TURN ON is selected, the following message function works.
The message of the “AUTO IN PROGRESS” for the auto 
adjustment.
The message of the “NO INPUT IS DETECTED”
The message of the “SYNC IS OUT OF RANGE”
The message of the “Searching…”
The message of the “Detecting…”
The indication of the input signal by input...

ViewSonic  PJ1172 31
OPTION Menu
With the OPTION menu, the items shown in the table below can 
be performed. Perform each operation in accordance with the 
instructions in the table below.
(This table is continued to the following page.) Item Description
VOLUME Adjust the volume using the S/T buttons.: 
    High  Low
SPEAKER Select TURN ON or TURN OFF using the S/T buttons.:
    TURN ON  TURN OFF
When TURN ON is selected, the built-in speaker works.
IR REMOTE Select a remote sensor using the S/T button...

ViewSonic  PJ1172 32
OPTION Menu (continued)
Item Description
SERVICE Pressing the X (or the ENTER) button calls the 
SERVICE menu.
SERVICE Menu
Select an item using the S/T buttons, and press the 
X (or the ENTER) button to perform each function.: 
   FANSPEED  AUTO ADJUST  LENS TYPE  LENS LOCK
FANSPEED Select the fan speed level using the S/T buttons.:
    HIGH  NORMAL
HIGH increases the rotation speeds of fans. Please use 
this function in using a projector at high elevations.
memo Note that the...

ViewSonic  PJ1172 33
NETWORK Menu
This projector provides the NETWORK function. If you use this 
function, please set up the projector according to the Network 
environment in which you use it.
memo When you use a Network suitable to the DHCP function, the 
following operation is not required commonly, because the TURN 
ON is selected to the item “DHCP” at the shipment time. Please see the section “Network 
Setting Up”.
Item Description
SETUP Pressing the X (or the ENTER) button calls 
the IP ADDRESS...

ViewSonic  PJ1172 34
Network Setting Up
This projector provides the NETWORK function. If you use this function, please consult 
your dealer for information.
To start, connect the NETWORK port to a gateway device via a RJ-45 (10BASE-1) cable, 
then set up the projector according to the Network environment in which you use it.
When you use a Network unsuitable to the DHCP function
Please set the IP Address, the Subnet Mask, the Gateway and the DHCP (on/off) using the 
NETWORK menu, referring to the section...

ViewSonic  PJ1172 35
Lamp
 WA R N I N GHIGH 
VOLTAGEHIGH 
TEMPERATUREHIGH 
PRESSURE
The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud 
bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that 
each lamp has a different lifetime, and some may burst or burn out soon after you start 
using them. In addition, when the bulb bursts, it is possible for shards of glass
 to fly into 
the lamp housing, and for gas containing mercury
 to escape...