ViewSonic Projector LS810 User Manual

							34
Setting the Presentation Timer
The presentation timer can indicate the presentation time on-screen to h\
elp you achieve 
better time management when giving presentations. Follow these steps to \
utilize this 
function:
1. Use the remote control 
 and enter Presentation Timer menu or enter Basic	>	
Presentation Timer menu.
2.  Press [Enter] to show the Presentation Timer page.
3.  Select Timer Interval and press / to confirm the duration. Duration can be set to 
1 to 5 minutes, with 1 minute increments, or 5 to 240 minutes in 5 minut\
e increments.
Once	the	timer	has	been	activated,	resetting	the	timer	interval	will	re-activate	the	timer.
4. Press  and select the Timer Display. Then press  / to select whether to display 
or hide the on-screen timer.
Selection Description
Always Displays the timer on screen throughout the presentation time.
1 min/2 min/3 min Display timer on-screen in the last 1 / 2 / 3 minutes.
Never Hides the timer throughout the presentation time.
5.  Press  and select Timer Position , and then press / to set timer location.
Upper left  Lower left  Upper right  Lower right
6.  Press  to select Timer Counting Direction , then press / to select the required 
timer method.
Selection Description
Count Up Increases from 0 to the preset time.
Count Down Decrease from the preset time to 0.
7.  To activate Presentation Timer, press , then press / and select Begin	
Countdown , then press [Enter].
8.  A confirmation message will be displayed next. Select  Ye s and press [Enter] to 
confirm the selection. The screen will display the message  [Timer is On!]. Once 
activated, the timer will start its countdown.
To	cancel	the	timer,	perform	the	following	steps:
1.  Enter Basic	>	Presentation	Timer menu.
2.  Select OFF . Press [Enter]. A confirmation message will be displayed afterwards.
3.  Select Ye s  and press [Enter] to confirm the selection. The screen will display the 
message [Timer is Off!].  
						

							35
Hiding the image
In order to draw the audience’s attention to the presenter, you may press Blank to hide the screen image. Press any key on the projector or remote to re\
store the 
image. After hiding the image, the lower right corner of the screen will display the text 
[BLANK].
You can go to Basic > Blank	Timer menu to set blank screen duration. Once the  blank screen countdown is complete, the image will be automatically re-d\
isplayed.
After	pressing	[Blank],	the	projector	will	automatically	enter	Power	Saving	mode.
 Caution 
Do not block the projector lens. The blocking item may be heated to the \
point of deformation or 
may	even	cause	a	fire.
Locking control keys
Locking the control buttons of the projector allows you to prevent proje\
ctor settings from being changed accidentally (by children, for example). Once  Panel Key Lock 
has been activated, with the exception of the 
 Power button, none of the buttons on 
the Projector could be used.
1.  Press 
 (Panel	Key	Lock) or enter System Settings > Panel Key Lock menu.
2.  Press / and select ON.
3.  A confirmation message will be displayed next. Select  Ye s to confirm your choice.
To switch off the Panel Key Lock, press and hold the 
 button on the Projector for 3 
seconds.
You may also use the remote to enter  System Settings > Panel Key Lock menu, 
press / and select OFF.
Buttons	on	the	remote	control	can	still	be	used	even	if	the	Panel	Key	Lock	function	has	been	
switched on.
If you press the  Power button to switch off the projector without switching off the Pane\
l Key 
Lock	function,	the	projector	buttons	will	remain	locked	when	you	switch	it	on	the	next	time.  
						

							36
Creating your own startup screen
In addition to Black, Blue, or ViewSonic screens, you may also select a computer or 
video projection image as your startup screen.
To create your own startup screen:
1.  Select the desired startup screen image from your computer or video sour\
ce.
2.  Open the OSD menu and enter  Basic > Screen Capture menu.
3.  Press [Enter].
4.  A confirmation message will be displayed next. Press [Enter] again.
5.  While the projector processes the image, the screen will display the mes\
sage 
[Screen Capture in Progress...]. Please wait.
6.  When successful, the screen will display the message [Screen Capture Suc\
cess]. 
The captured image will be saved as a  Screen Capture and set as your current 
startup screen.
In the unlikely event that the capturing action fails, change your targe\
t picture. When 
it happens, please set the resolution of the input signal under native r\
esolution and 
try again.
Operations at high altitudes
We recommend using the  High Altitude Mode when the environment is at 1500 to 
3000 meters above sea level and the temperature is between 5°C to 25°\
C.
 Caution 
Do not activate High Altitude Mode if the environment is at 0 to 1500 meters above sea level \
and 
the temperature is between 5°C to 35°C.  
Activating High Altitude Mode under such circumstances will lead to excessive cooling of\
 the 
projector.
Activating High Altitude Mode:
1.  Open the OSD menu and enter  System Settings > 
High Altitude Mode menu.
2.  Press  and select ON. / will display a 
confirmation message.
3.  Select Ye s , and then press [Enter].
There is a chance that louder operational noises 
will be generated when using the projector in  High 
Altitude Mode . The reason for this is the increased 
fan speed necessary to improve overall system 
cooling and performance.
Using this projector under extreme environments that exceed the aforemen\
tioned 
limits may lead to auto-shutdown designed to prevent overheating of the \
projector. 
Under such circumstances, you should switch to  High Altitude Mode to solve these 
issues. However, this does not mean that this projector is able to operate under any 
and all harsh or extreme conditions.  
						

							37
Using the CEC function
This projector supports Consumer Electronics Control (CEC), allowing y\
ou to connect 
to connect to HDMI and achieve synchronized power ON/OFF operations. This 
means that when a device that also supports CEC is connected to the HDMI\
 input 
jack of the projector, switching off the power of the projector will also automatically 
switch off the power of the connected device. Switching on the power of the 
connected device will also automatically switch on the projector.
Activating the CEC function:
1.  Open the OSD menu and enter  Power management > Auto Power On  > CEC 
menu.
2.  Press / and select Enable.
	 To	ensure	proper	operations	of	the	CEC	function,	please	verify	that	the	target	device	has	been	
connected to the HDMI input jack via an HDMI cable and that the CEC func\
tion has been 
activated.
CEC function may not be usable according to the connected equipment.
3D functions
This projector also comes with 3D functions that offer greater depth and immersion 
when viewing 3D movies, videos, sports, and games. You would need a pair of 3D 
glasses when viewing 3D images and videos.
If the 3D signal comes from an HDMI 1.4a compatible device, this project\
or will look 
for a 3D Sync data signal. Once detected, the projector will automatical\
ly switch to 3D 
projection. Under other circumstances, you may need to manually select t\
he 3D Sync 
format to ensure that the proper projection of 3D images.
Selecting 3D Sync formats:
1.  Use the 3D button on the remote control to enter the  3D Settings menu or enter 
Advanced > 3D Settings menu.
2.  Press [Enter] to bring up the 3D Settings page.
3.  Highlight  3D Glasses  and press / to select DLP or 3D VESA.
  Once 3D Sync function has been activated:   
•	Brightness	of	the	projected	image	will	be	reduced.	  
•	Color	modes	cannot	be	adjusted.	  
•	Zoom	functions	can	only	enlarge	the	image	to	a	limited	degree.	  
If	the	3D	image	has	been	severely	inverted,	you	may	set	the	3D	Sync	Invert	function	to	[Invert]	
to correct this problem.
Using the projector under standby mode
A number of projector functions can be used under Standby Mode (plugged \
in to 
power but not switched on). To use these functions, please check that you have 
switched on the  Power management > Standby Settings  and its secondary menu 
items, and that the cables have been properly connected. Refer to the ch\
apter on 
cable connections for more information on cable connections.  
						

							38
Active VGA Out
Once the COMPUTER IN and COMPUTER OUT jacks have been properly connected 
to the corresponding devices, select ON to generate VGA signal output. The projector 
will only receive output signals via Computer In 1.
Active Audio Out
When the AUDIO IN jack is correctly connected to a device, select  ON to output audio 
signals.
Adjusting the sound
The sound adjusents made as below will have an effect on the projector speaker(s). 
Please check that you have made a correct connection to the projector au\
dio input / 
output jacks. See “Connection”  for details.
Adjustments in Audio Mode
1. Open the OSD menu and enter  Basic > Audio Settings > Audio Mode menu.
2.  Press / to select the primary Audio Mode.
If	available,	you	may	press	the	[Audio	Mode]	on	the	remote	control	to	select	the	primary	 Audio	mode.
Mute
1. Open the OSD menu and enter  Basic > Audio Settings > Mute menu.
2.  Press / and select ON.
If	available,	you	may	press	the	 button on the remote control to switch the projector audio 
ON or OFF.
Adjusting the sound level
1.  Open the OSD menu and enter  Basic > Audio Settings > Audio Volume menu.
2.  Press / to select the desired volume.
If	available,	you	may	press	the	 button on the remote control to adjust speaker volume of 
the projector.
Switch off the projector
1.  Press the  Power button. A confirmation message will be displayed on screen. The 
message will disappear if you do not respond within a few seconds.
2.  Press the 
 Power button again.
3.  Disconnect the power cord from the wall socket if the projector will not\
 be used in an 
extended period of time.  
						

							39
Menu operations
Menu system
Please note that the on-screen display (OSD) menu may vary according t\
o the type of 
signal received.
The projector must detect at least one valid signal in order to use the \
menu items. If no 
device has been connected to the projector or if no signal has been dete\
cted, only a few 
menu items will be accessible.
Main menuSub-menu Options
1.
Display Screen Color
Off/Blackboard/Greenboard/
Whiteboard
Aspect Ratio Auto/4:3/16:9/16:10/2.35:1
Keystone Auto V Keystone
Off/On
Manual Vertical/Horizontal
Corner Adj.
Position
Phase
H. Size
Zoom
OverScan Off/1/2/3/4/5
2.
Picture Color mode
Brightest/Dynamic/Standard/ViewMatch	sRGB/
Movie
Brightness
Contrast
Color Temperature Warm
Red	Gain/Green	Gain/Blue	
Gain/Red Offset/Green 
Offset/Blue	Offset
Normal
Neutral
Cool
Color
Advanced Tint
Sharpness
Gamma
1/2/3/4/5/6/7/8
Brilliant	Color Off/1/2/3/4/5/6/7/8/9/10/13
Noise Reduction
Color Management Primary color
Tint
Saturation
Gain
Reset color settings Restore/Cancel  
						

							40
Main menuSub-menu Options
3.
Power 
Management Auto Power On
Computer
Disable/Enable
CEC Disable/Enable
Direct power on Off/On
Smart Energy Auto Power Off
Disable/10 min/20 min/ 
30 min
Sleep Timer Disable/30 min/1 hr/2 hr/
 
3 hr/4 hr/8 hr/12 hr
Power saving Disable/Enable
MHL settings Power Out
MHL/USB-TYPE	A
MHL reset Restore/Cancel
Standby Settings Active VGA Out
Off/On
Active Audio Out Off/On
4.
Basic Audio Settings
Audio Mode
Standard/Speech/
Entertainment
Mute On/Off
Volume
Presentation Timer Timer Period
1~240 m
Timer Display Always/1 min/2 min/3 min
Timer Position Top-Left/Bottom-Left/Top-
Right//Bottom-Right
Timer Counting 
Direction Count Down/Count Up
Start Counting/Off
Pattern Off / 1/ 2/ 3
Blank	Timer Disable/5 min/10 min/15 
min/20 min/25 min/30 min
Message On/Off
Splash Screen Black/Blue/ViewSonic/
Screen Capture/Off
Screen Capture
My	Button Auto/Projection	(Projector	Position)/Menu	
Position/Color	Temp./Brightness/Contrast/3D	
Settings/Screen Color/Splash Screen/Message/
Quick Auto Search/CEC/DCR/Closed Caption/
Power Saving/Freeze/INFORMATION/Aspect 
Ratio/Power Out  
						

							41
Main menuSub-menu Options
5.
Advanced 3D Settings
3D Glasses
DLP/3D VESA
3D Sync Auto/Off/Frame Sequential/
Frame	Packing/Top-Bottom/
Side-by-Side
3D Sync Invert Disable/Invert
HDMI Settings HDMI Format
Auto/RGB/YUV
HDMI Range Auto/Enhanced/Normal
LAN Control 
Settings LAN Control 
Settings
DHCP ON/Static IP
Projector IP 
Address
Subnet Mask
Default Gateway
DNS Server
Standby LAN 
Control Off/On
Apply
Light Source 
Settings Light Source Mode
Normal/Eco
Light Source Hours
DCR On/Off
Closed Caption Caption VersionOff/ CC1/ CC2/ CC3/ CC4
Reset Settings Reset/Cancel
5.
System Language
Multi-language OSD 
selection
Projector Position Front Table/Rear Table/Rear 
Ceiling/Front Ceiling
Menu Settings Menu Display Time
5 sec/10 sec/15 sec/20 
sec/25 sec/30 sec
Menu Position Center/Top-Left/Top-Right/
Bottom-Left/Bottom-Right
High Altitude Mode On/Off
Quick Auto Search On/Off
Security Settings Change Password
Power On Lock
On/Off
Panel Key Lock On/Off
Remote Control 
Code 1/2/3/4/5/6/7/8
6.
Information •	Source
•	Color	Mode
•	Resolution
•	Color	System	
•	IP
	Address
•	MAC	 Address
•	Firmware	Version  
						

							42
Description of each menu
FUNCTIONDescription
1. Display menu
Screen ColorSee “Using Screen Color” for details.
Aspect Ratio See “Selecting the aspect ratio”  for details.
Keystone See “Correcting keystone” for details.
Corner Adj. See “Adjusting the 4 corners”  for details.
Position Displays the position adjustment page. To move the 
projected image, use the directional arrow keys. The 
values shown on the lower position of the page change 
with every key press you made until they reach their 
maximum or minimum.
This function is only available when a PC input signal is 
selected.
The adjustment range may vary under different timings.
Phase
Adjusts the clock phase to reduce image distortion. 
  This function is only available when a PC input signal is 
selected.
H. Size
Adjusts the horizontal width of the image.This function is only available when a PC input signal is 
selected.
Zoom
See “Magnifying and searching for details”  for details.
OverScan Adjusts the overscan rate from 0% to 5%.
This	function	is	only	available	when	a	Composite	Video,	
S-Video or HDMI input signal is selected.
2. Image menuColor mode
See “Selecting a picture mode”  for details.
Brightness See “Adjusting Brightness” for details.
Contrast See “Adjusting Contrast” for details.
Color Temperature For more details, please refer to 
“Selecting a 
Color Temperature”  and “Setting a preferred color 
temperature” .  
						

							43
FUNCTIONDescription
2. Image menu
AdvancedColor
See “Adjusting Color”
 for details.
Tint
See “Adjusting Tint” for details.
Sharpness
See “Adjusting Sharpness”  for details.
Gamma
See “Selecting a gamma setting”  for details.
Brilliant	Color
See “Adjusting Brilliant Color”  for details.
Noise Reduction
See “Reducing image noise”  for details.
Color Management
See “Color Management”  for details.
Reset color settings Returns all color settings to the factory preset values.
3. Power Management menu
Auto Power OnComputer
Selecting 
Enable allows the projector to turn on 
automatically once the VGA signal is fed through the 
VGA cable.
CEC
See “Using the CEC function”  for details.
Direct power on
Selecting  On allows the projector to turn on 
automatically once the power is fed through the power 
cord.
Smart Energy Auto Power Off
See “Setting Auto Power Off” for details.
Sleep Timer
See “Setting Sleep Timer” for details.
Power Saving
See “Setting Power Saving”
 for details.
MHL Settings Please check your MHL dongle and Power Output of 
OSD settings before used.   
If you’d like to have power charging through additional 
USB-type A, make sure to switch the Power Output 
from MHL to USB-type A.
MHL Reset
Selecting 
Reset to reapply power after a power outage.