ViewSonic Pro8200 Projector User Manual

ViewSonic  Pro8200 19
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one 
of the following output sockets:
„Component Video
„S-Video
„Video (composite)
You need only connect the projector to a Video source device using just one of the 
above connecting methods, however each provides a different level of video quality. 
The method you choose will most likely depend upon the availability of matching 
terminals on both the projector and the...

ViewSonic  Pro8200 20
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component 
Video output sockets available:
„If so, you can continue with this procedure.
„If not, you will need to reassess which method you can use to connect to the 
device.
To connect the projector to a Component Video source device:
1. Take a VGA (D-Sub) to HDTV (RCA) cable, Component Video cable or a 
Component Video to VGA (D-Sub) adaptor and connect the end with...

ViewSonic  Pro8200 21
Important
„If the selected video image is not displayed after the projector is turned on 
and the correct video source has been selected, check that the Video source 
device is turned on and operating correctly. Also check that the signal cables 
have been connected correctly.
„If you have already made a Component Video connection between the 
projector and this S-Video source device using Component Video 
connections, you need not connect to this device using an S-Video 
connection...

ViewSonic  Pro8200 22
Operation
Powering On/Off the Projector
Powering On the Projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press   to turn on the projector.
The projector takes a minute or so to warm up. 
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically
detects your source.
„If you are connecting multiple sources to the projector simultaneously, press
SOURCE on the projector to select your...

ViewSonic  Pro8200 23
Adjusting the Projector Height
The projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image:
1. To raise or lower the image, press the elevator button and raise or lower the front
of the projector. Release the button to lock the adjustment.
2. To level the image on the screen, turn the tilt-adjustment feet to fine-tune the 
height.
Adjusting the Projector Zoom and Focus
1. Focus the image by rotating the focus ring. A still image is...

ViewSonic  Pro8200 24
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
Screen size
Diagonal
[inch (cm)]16 : 9 Screen
Projection distance [inch (m)] Image 
height [inch 
(cm)]Vertical 
offset
 [inch (cm)] (min. zoom) (max. zoom)
30 (76) 35 (0.89) 55 (1.39) 14.7 (37) 5.0 (12.8)
40 (102) 48 (1.21) 74 (1.87) 19.6 (50) 6.7 (17.1)
50 (127) 60 (1.52) 93 (2.35) 24.5 (62) 8.4 (21.4)
60 (152) 72 (1.83) 111 (2.83) 29.4 (75) 10.1 (25.6)
80...

ViewSonic  Pro8200 25
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings 
from being changed accidentally (by children, for example). When the Panel Key 
Lock is on, no control keys on the projector will operate except 
 Power.
1. Press  on the projector or remote control.
2. A confirmation message is displayed. Select 
Ye s to confirm.To release panel key lock, press and hold  for 
3 seconds on the projector.
Important
„Keys on the remote control...

ViewSonic  Pro8200 26
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image 
adjustments and change a variety of settings.
Video/Audio-5 - +5
Audio Setting
Computer 1
Computer 2
Video Source Color Temp.
Red Gain
Green Gain
Blue Gain
User, LOW, MID, HIGH 0 - 100
0 - 100
0 - 100
Color
Hue
Saturation
Gain
Red, Green, Blue, 
Cyan, Megenta, Yellow
-100 - +100
-100 - +100
-100 - +100
Setting
Filter Mode*2
High AltitudeFront-Table, Front-Ceiling, 
Rear-Table,...

ViewSonic  Pro8200 27
Black, Red, Green, Blue, 
Cyan, Yellow, Magenta, White
Message
Information
Factory Default Equivalent Lamp Hours
Equivalent Lamp Hours
ResetFilter Hours*2
Filter Hours Reset*2Input Password
Password DeleteOff, CC1, CC2, CC3, CC4, T1, T2
Input SourceComputer  1, Computer 2, 
Component, Composite, 
S-Video, HDMI, USB 1, USB 2
OSD Setting
OSD TimeoutTop-Left, Bottom-Left, 
Top-Right, Bottom-Right
20 - 600, 10, 20, 30, 40, 50, 60, 70, 80, 90OSD Transparency
Zoom
DCR
Test Pattern Others...

ViewSonic  Pro8200 28
How to operate
1. Press MENU on the projector or Menu on the remote control to open the OSD menu.
2. When OSD is displayed, use S / T to select any feature in the main menu.
3. After selecting the desired main menu item, press X to enter sub-menu for feature
setting.
4. Use 
S / T to select the desired item and adjust the settings with W / X.
5. Press MENU on the projector or Menu on the remote control, the screen will return to
the main menu.
6. To exit OSD, 
Press MENU on the...