ViewSonic Pro6200 Projector User Manual

14
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component
Video output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a VGA (D-Sub) to HDTV (RCA) cable and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source...

15
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite
Video output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of
the!Video source device.
2. Connect the other end of the Video cable to...

16
Operation
Powering on/off the projector
Powering on the projector:
1. Complete the AC power cord and peripheral signal cable(s) connections.
2. Press   to turn on the projector.
The projector takes a minute or so to warm up. 
3. Turn on your source (computer, notebook, DVD, etc.). The projector automatically
detects your source.
• If you are connecting multiple sources to the projector simultaneously, press 
SOURCE on the projector or Source on the remote control to select your 
desired signal or...

17
Adjusting the projector height
The projector is equipped with an elevator foot to adjust the image height. To raise or 
lower the image, turn the elevator foot to fine-tune the height.
Note
• To avoid damaging the projector, make sure that the elevator foot is fully retracted 
before placing the projector in its carrying case.
Adjusting the Projector Zoom and Focus
1. Focus the image by rotating the focus ring. A still image is recommended for
focusing.
2. Adjust the image size by rotating the zoom...

18
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection
distance.
Note
• Position the projector in a horizontal position; other positions can cause heat build-up 
and damage to the projector.
• Keep a space of 30 cm or more between the sides of the projector.
• Do not use the projector in a smoky environment. Smoke residue may build-up on 
critical parts and damage the projector or its performance.
• There is 10%  tolerance among these numbers...

19
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings
from being changed accidentally (by children, for example). When the Panel Key
Lock is on, no control keys on the projector will operate except   Power.
1. Press Lockon the remote control.
2. A confirmation message is displayed. Select Ye s to
confirm.
To release panel key lock:
1. Press Lockon the remote control.
2. A confirmation message is displayed. Select Ye s to
confirm. 

20
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help you
achieve better time management when giving presentations. Follow these steps to uti-
lize this function:
1. Go to the Option > Presentation Timer menu and press  on the projector or
Enter on the remote control to display the Presentation Timer page.
2. Highlight Timer Period and decide the timer period by pressing  / .
Important
• If the timer is already on, the timer will restart...

 21 Menu operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings.
Start up ScreenOff(Blue),ViewSonic,
Screen Capture
Screen Capture
Screen Capture Delete
Active VGA Out
Active audio Out Start up Screen
Auto Keystone
PC sourceÖ
Brightest,Standard,Movie,ViewMatch,
User1,User2,White board,Black board,
Green board
Video sourceÖ
Brightest,Gaming,Movie,ViewMatch,
User1,User2,White board,Black board,
Green board
PC source:...

 22
Quick Power Off 

 23
How to operate
1. Press MENU on the projector or Menu on the remote control to open the OSD
menu.
2. When OSD is displayed, use  /  to select any feature in the main menu.
3. After selecting the desired main menu item, press   to enter sub-menu for feature
setting.
4. Use  /  to select the desired item and adjust the settings with  / .
5. Press MENU on the projector or Menu on the remote control, the screen will
return to the main menu.
6. To exit OSD, Press MENU on the projector or Menu on the...