ViewSonic Pjd8333s Projector User Manual

 34
Note
•
This function is only available when the HDMI-input port is in use.
•When HDMI Format is “Auto”, HDMI Range will be gray out.
HDMI Range
• Enhanced: The range for HDMI output signal is from 0 - 255.
• Normal: The range for HDMI output signal is from 16 - 235.
Blank Screen
To select the screen color when Blank function is active.
Start up Screen
Allows you to select which logo screen will display during projector start-up. Four
options are available: ViewSonic logo, Black screen, Screen...

 35
Smart Restart
Selecting On enables you to restart the projector immediately within 3 minutes after
turning it off. After 3 minutes, if the projector is not turned on again, it will directly enter
the standby mode.
DC12V
Set whether the DC12V function works when the projector is in standby (powered off
but connected to AC power).
LAN Control Setting
Wired LAN
Allow you to configure the wired LAN settings. Refer to page 38.
• Status: Display the projector’s status.
• DHCP: Abbreviation for Dynamic Host...

 36
Network Restart
If you encounter a malfunction of network connection and need to restart the network 
settings, you can go into the Setting > LAN Control Setting > Network Restart 
menu to restart network function.
Option
Closed Caption
Enable or disable closed captions by selecting CC1 (closed caption1, the most 
common channel), CC2, CC3, CC4, T1, T2 or OFF.
Password
Set, change or delete the password. When the password function is added, image
projection will require to input the preset password...

 37
Information
Input Source
Display the current input source.
Resolution
Display current input source resolution.
H. Frequency
Display current image horizontal  frequency.
V. Frequency
Display current image vertical frequency.
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
MAC Address
Display the MAC address. 

 38
Controlling the projector through a LAN environment
You can manage and control the projector from one or more remote computers when 
they are properly connected to the same local area network.
Wired connection
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the 
projector and the other end to the RJ45 port on your Ethernet or router.
2. Press MENU/EXIT on the projector or Menu on the remote control and then go to 
Setting > Lan Control Setting...

 39
4. Press  to select the item you want to modify and press ENTER on the projector 
or Enter on the remote control.
5. Press  /  to move the cursor and the enter the value.
6. To save the settings, press ENTER on the projector or Enter on the remote 
control. If you do not want to save the settings, press MENU/EXIT on the projector
7. or Menu on the remote control.
8. Press 
 to highlight Apply and press ENTER on the projector or Enter on the 
remote control.
Important
•
If the RJ45 cables are not...

 40
About AP and Client modes
In AP mode, you need to use your computers wireless connection utility to search for the 
projectors SSID and connect to it. Then you can search for the projector with vsPresenter.
In Client mode, you should connect both your computer and projector to the same
 AP 
router and make connections with the IP address.
The following diagram describes how to access the Internet in AP and Client modes.
Important
•
If you need more information about AP and Client modes, please refer...

 41
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in 
standby mode, you can use any computer that is on the same local area network to 
control the projector.
Important
•
If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
•The screenshots in this manual are for reference only, and may differ from the actual 
design.
1. Enter the address of the projector in the address bar of your browser...

 42
4. The main page of the ViewSonic Network Control webpage appears as below.
5. To change the language for the web pages, click the down arrow to reveal a drop 
down list and select a desired language.
6. To download vsPresenter, click PC or MAC depending on your computer operating 
system. See Displaying images through vsPresenter on page 46 for details.
7. Wireless page displays the Wireless Lan information.
8. Network Settings: Provides network settings.
9. Email Alert: Allows you to setup the mail...

 43
Important
•
The Menu button can also be used to go back to previous OSD menus, exit and save 
menu settings.
•The source list varies according to the connectors available on the projector.
•When you use the projector control panel or remote control to change the OSD menu 
settings, it may take a while for the web browser to synchronize these changes with the 
projector.
2. The tools page allows you to manage the projector, configure the LAN control 
settings and secure access of remote network...