ViewSonic Pjd7583w Projector User Manual

Operation 57
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned 
on). To use these functions, be sure you have turned on the corresponding menus under 
SYSTEM SETUP: Basic  > Standby Settings , and the cable connections are correctly 
made. For the connection methods, see the Connection chapter.
LAN Control
Select  On when you wish to control the projector over a network when it is in standby 
mode.
Microphone
Select  On when you...

Operation
58
Shutting down the projector
1. Press  POWER and a confirmation message 
is displayed prompting you. 
If you dont respond in a few seconds, the 
message will disappear.
2. Press  POWER a second time.
3. Disconnect the power cord from the wall  socket if the projector wi ll not be used in an 
extended period of time.
CAUTION
• To protect the lamp, the projector will not respond  to any commands during the cooling process.
• Do not unplug the power cord before the projector  shutdown sequence...

Operation 59
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected.
The menu items are available when the projector  detects at least one valid signal. If there is 
no equipment connected to the projector or no signal detected, limited menu items are 
accessible.
Main menu Sub-menu Options
1. 
DISPLAY
Screen Color Off/Whiteboard/Greenboard/
Blackboard
Aspect Ratio • Auto/4:3/16:9 
(PJD7383/PJD7383i only)
• Auto/4:3/16:9/16:10...

Operation
60
Main menu Sub-menu Options
3. SOURCE
Quick Auto Search On/Off
PointBlank
(PJD7383i/
PJD7583wi 
only) Enabled Yes/No
Click Speed
Fast/Medium /Slow
Link Channel Auto/1/2/3/.../28
Handwriting 
Mode Lefthand 1/Lefthand 2/
Righthand 1/Righthand 2/User
Horizontal
Vertical
M Button Normal/Draw
Alt-Tab
Alt-Esc
Command-Tab
Left Mouse
Right Mouse
Middle Mouse
Double Click
PwrPnt Annotate
Interactive Software 

Operation 61
Main menuSub-menu Options
4. 
SYSTEM 
SETUP: 
Basic
Language
Projector Position Front Table/Rear Table/Rear 
Ceiling/Front Ceiling
Auto Power Off Disable/5 min/10 min/20 min/
30 min/40 min/50 min/60 min
Blank Timer Disable/5 min/10 min/15 min/
20 min/25 min/30 min
Panel Key Lock On/Off
Splash Screen Black/Blue/ViewSonic/Screen 
Capture/Off
Screen Capture
Message On/Off
LAN Control 
Settings Wired LAN Status
Connect/
Disconnect
DHCP On/Off
IP Address
Subnet Mask
Default 
Gateway
DNS
Apply...

Operation
62
Main menu Sub-menu Options
5. 
SYSTEM 
SETUP: 
Advanced
High Altitude Mode On/Off
DCR On/Off
Audio Settings Mute
On/Off
Volume
Microphone Volume
Menu Settings Menu Display 
Time
5 sec/10 sec/15 sec/20 sec/25 
sec/30 sec
Menu Position Center/Top-Left/Top-Right/
Bottom-Left/Bottom-Right
Closed Caption Closed Caption 
Enable
On/Off
Caption Version CC1/CC2/CC3/CC4
Lamp Settings Lamp Mode Normal/Economic
Reset Lamp Timer
Equivalent Lamp Hour
Presentation 
Timer Timer Period 1~240 minutes
Timer...

Operation 63
Description of each menu
FunctionDescription
Screen ColorCorrects the projected picture’s color when the projection surface 
is not white. See  Using Screen Color on page 32  for details.
Aspect RatioThere are three options to set the images aspect ratio depending 
on your input signal source. See Selecting the aspect ratio on 
page 29  for details.
KeystoneCorrects any keystoning of the image. See  Correcting keystone 
on page 28 for details.
Position
Displays the position  adjustment...

Operation
64 Function Description
Color ModePre-defined picture modes ar
e provided so you can optimize 
your projector image set-up to suit your program type. See 
Selecting a picture mode on page 31  for details.
Reference 
ModeSelects a picture mode that most suits your need for the image 
quality and further fine-tune the image based on the selections 
listed on the same page below. See Setting the User 1/User 2 
mode on page 32 for details.
BrightnessAdjusts the brightness of the image. See...

Operation 65
Function Description
LanguageSets the language for the On-Screen Display (OSD) menus. See 
Using the menus on page 23
 for details.
Projector 
PositionThe projector can be installed on  a ceiling or behind a screen, or 
with one or more mirrors. See  Choosing a location on page 12  
for details.
Auto Power 
OffAllows the projector to turn of f automatically if no input signal 
is detected after a set period of time. See  Setting Auto Power 
Off on page 69  for details.
Blank TimerSets the...

Operation
66 Function Description
Audio 
Settings
The sound adjustments made as below will have an effect on the 
projector speaker. Be sure you ha
ve made a correct connection to 
the projector audio input/output jacks. See  Connection on page 
15 and Playing sound through the projector on page 19  for 
more details.
Mute
Mutes the sound received from  AUDIO IN 1 and AUDIO IN 2 
(L/R) . It will not affect the microphone sound level.
Volume
Adjusts the sound level received from  AUDIO IN 1 and AUDIO 
IN...