ViewSonic Pjd6683w Projector User Manual

							56
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is 
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts 
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
• Use a canister of compressed air to remove dust.
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens 
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as 
described in "Shutting down the projector" on page 45 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH 
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the 
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the 
recommended range for the projector. Please refer to"Specifications" on page 64 or 
consult your dealer about the range.
• Retract the adjuster feet.
• Remove the battery from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent. 
						

							57
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically 
calculated by the built-in timer.
To obtain the lamp hour information:
1. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the SYSTEM SETUP: Advanced menu is highlighted.
2. Press  to highlight Lamp Settings and press MODE/ENTER on the projector or 
ENTER on the remote control. The Lamp Settings page is displayed.
3. You will see the Equivalent lamp hour information on the menu.
4. To leave the menu, press MENU/EXIT on the projector or Exit on the remote 
control.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item. To keep the lamp life as long as possible, you 
can do the following settings via the OSD menu.
Setting Lamp Mode as Economic
UsingEconomic mode reduces system noise and power consumption by 20%. If the 
Economic mode is selected, the light output will be reduced and result in darker projected 
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set 
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > Lamp
Mode menu and press  / .
Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is detected 
after a set period of time to prevent unnecessary waste of lamp life.
To  s e t  Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off menu and 
press  / . If the preset time lengths are not suitable for your presentation, select Disable.
The projector will not automatically shut down in a certain time period. 
						

							58
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to 
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a 
malfunction in the projector and in some instances the lamp may explode.
CAUTION
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too 
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator 
still lights up after turning the power back on, please contact your dealer. See "Indicators" on 
page 62 for details.
The following lamp warning displays will remind you to change the lamp.
StatusMessage
Install a new lamp for optimal performance. If the 
projector is normally run with Economic selected 
(See "Setting Lamp Mode as Economic" on page 
57), you may continue to operate the projector 
until the next hour lamp warning appears.
A new lamp should be fitted to avoid the 
inconvenience when the projector runs out of lamp 
time.
It is strongly recommended that you replace the 
lamp at this age. The lamp is a consumable item. 
The lamp brightness diminishes with use. This is 
normal lamp behavior. You can replace the lamp 
whenever you notice that the brightness level has 
significantly diminished. If the lamp is not 
replaced beforehand, it must be replaced when 
you see this message.
The lamp MUST be replaced before the projector 
will operate normally.
OK
Order Replacement Lamp
Lamp > ____ Hours
Notice
OK
Replace Lamp Soon 
Lamp > ____ Hours
Notice
OK
Replace Lamp Now 
Lamp > ____ Hours
Lamp usage time exceeded
Notice
OK
Lamp usage time exceeded
Replace lamp (refer to User Manual)
Then reset lamp timer
Notice 
						

							59
Replacing the lamp
To prepare a new lamp, contact your dealer and tell the lamp type number.
Type number:
Type number: 
WARNING
Hg - Lamp contains mercury. Manage in accordance with local disposal 
laws. See www.lamprecycle.org
• To reduce the risk of electrical shock, always turn the projector off and disconnect the 
power cord before changing the lamp.
• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes 
before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution 
when removing lamp glass that has shattered into sharp pieces. Before replacing the 
lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp 
edges in the lamp compartment. Wash hands after lamp replacement.
• Only ViewSonic certified lamps are tested with this projector. Use of other lamps may 
cause electrical shock and fire.
1. Turn the power off and disconnect the 
projector from the wall socket. If the 
lamp is hot, avoid burns by waiting for 
approximately 45 minutes until the 
lamp has cooled.
2. Loosen the screws that secure the lamp 
cover on the both sides of the projector 
until the lamp cover loosens.
3. Remove the lamp cover from the 
projector.
WARNING
• Do not turn the power on with the lamp 
cover removed.
• Do not insert your fingers between the 
lamp and the projector. The sharp edges 
inside the projector may cause injuries.
4. Remove and dispose of the lamp 
protection film.
1
2
Type number: 
 RLC-070
FPJD5226w/PJD6223/PJD6353/PJD6353s/PJD6653w/PJD6653ws
 RLC-077

FPJD5126/PJD5226
G
 RLC-071
FPJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683w/PJD6683ws
G
G 
						

							60
5. Loosen the screw that secures the lamp.
6. Lift the handle so that it stands up. Use 
the handle to slowly pull the lamp out 
of the projector.
CAUTION
• Pulling it too quickly may cause the lamp 
to break and scatter broken glass in the 
projector.
• Do not place the lamp in locations where 
water might splash on it, children can 
reach it, or near flammable materials.
• Do not insert your hands into the projector 
after the lamp is removed. If you touch the 
optical components inside, it could cause 
color unevenness and distortion of the 
projected images.
7. Insert the new lamp into the lamp 
compartment and make sure it fits in 
the projector.
8. Tighten the screw that secures the lamp.
CAUTION
• Loose screw may cause a bad connection, 
which could result in malfunction.
• Do not over tighten the screw.
9. Ensure the handle is fully laid flat and 
locked in place. 
						

							61
13. Restart the projector.
CAUTION
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
14. After the startup logo, open the On-Screen 
Display (OSD) menu.
15. Go to the SYSTEM SETUP: Advanced > 
Lamp Settings menu. Press MODE/ENTER
on the projector or ENTER on the remote 
control. The Lamp Settings page is 
displayed. 
16. Press  to highlight Reset lamp timer and 
pressMODE/ENTER on the projector or 
ENTER on the remote control. A warning 
message is displayed asking if you want to 
reset the lamp timer. 
17. Highlight Reset and press MODE/ENTER
on the projector or ENTER on the remote 
control. The lamp time will be reset to '0'.
CAUTION
Do not reset if the lamp is not new or replaced as this 
could cause damage. 
10. Place the lamp protection film supplied 
with the new lamp on the lamp 
compartment.
11. Replace the lamp cover on the 
projector.
12. Tighten the screws that secure the lamp 
cover.
CAUTION
• Loose screw may cause a bad connection, 
which could result in malfunction.
• Do not over tighten the screws.
2
1
Reset Lamp Timer?
ResetCancel
Notice 
						

							62
Indicators
LightStatus & Description
PowerTe m pLamp
Power events
Blue
FlashingOff OffStand-by mode
Blue Off OffPowering up
Blue Off OffNormal operation
Lamp events
Purple
FlashingOff RedThe projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact 
your dealer for assistance.
Off Off Red1. The projector needs 90 seconds to cool down. Or
2. Please contact your dealer for assistance.
Thermal events
Off Red Off
The projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact 
your dealer for assistance.
Off Red Red
Off Red Green
Red Red Red
Red Red Green
Blue Red Red
Blue Red Green
Purple Red Red
Purple Red Green
Off Green Red 
						

							63
Troubleshooting
The projector does not turn on.
No picture
Blurred image
Remote control does not work
CauseRemedy
There is no power from the power 
cord.Plug the power cord into the AC inlet on the 
projector, and plug the power cord into the 
power outlet. If the power outlet has a switch, 
make sure that it is switched on.
Attempting to turn the projector on 
again during the cooling process.Wait until the cooling down process has 
completed.
CauseRemedy
The video source is not turned on or 
connected correctly.Turn the video source on and check that the 
signal cable is connected correctly.
The projector is not correctly 
connected to the input signal device.Check the connection.
The input signal has not been 
correctly selected.Select the correct input signal with the 
SOURCE key on the projector or remote 
control.
The lens cover is still closed. Open the lens cover.
CauseRemedy
The projection lens is not correctly 
focused.Adjust the focus of the lens using the focus 
ring.
The projector and the screen are not 
aligned properly.Adjust the projection angle and direction as 
well as the height of the projector if necessary.
The lens cover is still closed. Open the lens cover.
CauseRemedy
The battery is out of power. Replace the battery with a new one.
There is an obstacle between the 
remote control and the projector.Remove the obstacle.
You are too far away from the 
projector.Stand within 8 meters (26 feet) of the 
projector. 
						

							64
Specifications
Projector specifications
All specifications are subject to change without notice.
General
Product name DLP Projector
Optical
ResolutionPJD5126:
800 x 600 SVGA
:
1024 x 768 XGA
1280 x 800 WXGA
Display system 1-CHIP DMD
Lamp
180 W lamp
240 W lamp
Electrical
Power supply
AC100–240V, 2.9 A, 50/60 Hz (Automatic)
AC100–240V, 3.5 A, 50/60 Hz (Automatic)
Power 
consumption 285 W (Max); < 1 W (Standby)
350 W (Max); < 1 W (Standby)
Mechanical
Weight
2.6 Kg (5.74 lbs)
2.99 Kg (6.6 lbs)
Not all models can be purchased in your region.•  • 
PJD5226/PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383
PJD5226w/PJD6553w/PJD6653w/PJD6653ws/PJD6683w/PJD6383s:
/PJD6383ws:
PJD5126/PJD
5226/PJD5226w/PJD6223/PJD6353/
PJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683wPJD6353s/
PJD6653w/PJD6653ws:
/PJD6683ws:
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6353/PJD6353s/PJD6653w/PJD6653ws:
PJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683w/PJD6683ws:
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6353/PJD6353s/PJD6653w/PJD6653ws:
PJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683w/PJD6683ws:
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6253/PJD6553w:
PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws: 
						

							65 Input terminal
Computer input
     RGB input D-Sub 15-pin (female) x 2
Video signal input
     S-VIDEO Mini DIN 4-pin port x 1
     VIDEO RCA jack x 1
SD/HDTV signal 
input
Analog – D-Sub  Component RCA jack x 3 
                (through RGB input)
Digital –PJD5126/PJD5226/PJD5226w:
N/A
HDMI V1.3 x 1
Audio signal input PC audio jack x 1 PC audio jack x 2
Output terminal
RGB output D-Sub 15-pin (female) x 1
SpeakerPJD5126/PJD5226/PJD5226w:
2 watt x 1
10 watt x 1
Control terminal
RS-232 serial 
control9 pin x 1
LANPJD5126/PJD5226/PJD5226w:
N/A
RJ45x 1
USB serial control Type mini B
IR receiverPJD5126/PJD5226/PJD5226w:
x 1 (Front)
x 2!(Front and Top)
Environmental Requirements
Operating
temperature0°C–40°C at sea level
Operating relative 
humidity10%–90% (without condensation)
Operating altitude • 0–1499 m at 0°C–35°C
• 1500–3000 m at 0°C–30°C (with High Altitude Mode on)
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws: