ViewSonic Pjd6553w Projector User Manual

							26
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security  Settings > Power On Lock  menu after opening the OSD menu system. Select Off by  
pressing / . The message INPUT PASSWORD is displayed. Enter the current  password.  
• If the password is correct, the OSD menu returns to the  Security Settings page  
with  Off shown in the row of Power On Lock. You will not have to enter the  
password next time you turn on the projector. 
• If the password is incorrect, the password  error message is displayed lasting for  
three seconds, and the message  INPUT PASSWORD is displayed for your  
retry. You can press  MENU/EXIT on the projector or Exit on the remote  
control to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should  you ever need to re-activate the password function by entering the old password. 
						

							27
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only  display one full screen at a time.  
Be sure the  Quick Auto Search function in the SOURCE menu is On if you want the  projector to automatically search for the signals. 
You can also manually select the desired signal by  pressing one of the source selection keys on the  remote control, or cycle through the available input signals. 
1. Press  SOURCE on the projector or remote  
control. A source selection bar is displayed.  
2. Press  /  until your desired signal is  
selected and press  MODE/ENTER on the  
projector or  Enter on the remote control. 
Once detected, the select ed source information  
will be displayed on the screen for seconds. If 
there are multiple devices connected to the 
projector, repeat steps 1-2 to search for another 
signal.
• The brightness level of the projected image will  change accordingly when you switch between different input signals. Data (graphic) PC  presentations using mostly static images are  generally brighter than Video using mostly moving images (movies). 
• The input signal type effects the options available  for the Color Mode. See  Selecting a picture  mode on page 32  for details. 
• The native display resolution of this projector is in  a 4:3 aspect ratio. For best display picture results, you should select and use an input signal which  outputs at this resolution. Any other resolutions  will be scaled by the projector depending upon the aspect ratio setting, which may cause some  image distortion or loss of picture clarity. See  Selecting the aspect ratio on page 30  for details.
Changing Color Space
This function is only available for the PJD6223/ PJD6253/PJD6553w series.
In the unlikely event that you connect the projector  to a DVD player via the projector’s  HDMI input and  the projected picture disp lays wrong colors, please  change the color space to  YUV. 
To do this:
1. Open the OSD menu and go to the  SOURCE menu. 
2. Press  to highlight  Color Space Conversion and press  /  to select a suitable  
color space.
This function is only  available when the HDMI-input port is in use.
ZOOM
TEMP LMMPMODE ENTER AUTOSOURCEMENU EXIT
TEMP LMMPMODE ENTER AUTOMENU EXITSOURCE
D-Sub / Comp. 1  
Video 
S-Video 
D-Sub / Comp. 2 
PJD5126 
PJD6223/PJD6253/PJD6553w
D-Sub / Comp. 1  
Video 
S-Video 
D-Sub / Comp. 2  
HDMI 
						

							28
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 2 rear adjuster feet. These  adjusters change the image height and pr ojection angle. To adjust the projector: 
1. Press the quick-release button and lift the  
front of the projector. Once the image is 
positioned where you want it, release the 
quick-release button to lock the foot in 
position.
2. Screw the rear adjuster feet to fine tune the 
horizontal angle.
To retract the foot, hol d up the projector while  pressing the quick-release button, then slowly lower the projector. Screw  the rear adjuster feet  in a reverse direction. 
If the projector is not pl aced on a flat surface or  the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see  Correcting keystone on page 29 for details.
• Do not look into the lens while the lamp is on.  The strong light from the lamp may cause damage to your eyes. 
• Be careful when you press the adjuster button  as it is close to the exhaust vent where hot air comes from.
Auto-adjusting the image
In some cases, you may need to optimize the  picture quality. To do this, press  AUTO on the  projector or  Auto Sync on the remote control.  Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality. 
The current source information will be  displayed in the upper left corner of the screen for 3 seconds.
• The screen will be blank while AUTO is  functioning. 
• This function is only available when PC  signal (analog RGB) is selected. 
1
2 
ZOOM
TEMP LMMPMODE ENTER AUTOSOURCEMENU EXIT
TEMP LMMPMODE ENTERSOURCEMENUEXITAUTO 
						

							29
Fine-tuning the image clarity 
Correcting keystone
Keystoning refers to the situation where the pr ojected image is noticeably wider at either the  top or bottom. It occurs wh en the projector is not perpendicular to the screen. 
To correct this, besides adjust ing the height of the projector, you will need to manually  correct it following one of these steps. 
• Using the remote control 
Press  /  on the projector or remote control to  display the Keystone correction page. Press   to correct keystoning at the t op of the image. Press    to correct keystoning at the bottom of the image. 
• Using the OSD menu 
1. Press  MENU/EXIT on the projector or  
Menu  on the remote control and then press  
/  until the DISPLAY menu is  
highlighted. 
2. Press  to highlight  Keystone and press  
MODE/ENTER  on the projector or Enter  
on the remote control. The  Keystone  
correction page is displayed.
3. Press   to correct keys toning at the top of  
the image or press   to correct keystoning at 
the bottom of the image. 
1.Adjust the projecte d image to the size  
that you need using the zoom ring.
2.  If necessary, Sharpen the image by  
rotating the focus ring. 
ZOOM
TEMP LMMPMODE ENTER AUTOSOURCEMENU EXIT
TEMPMODE ENTERSOURCEMENUEXITAUTOLMMP 
Press/. Press /. 
						

							30
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the  direction arrow keys for  navigating the picture. 
• Using the remote control 
1. Press  Magnify on the remote control to  
display the Zoom bar. 
2. Press   repeatedly to magnify the picture to  
a desired size.
3. To navigate the picture, press  MODE/ 
ENTER  on the projector or Enter on the  
remote control to switch to the paning mode 
and press the directional arrows  
( , , , ) to navigate the picture. 
4. To reduce size of the picture, press  MODE/ENTER on the projector or Enter on the  
remote control to switch  back to the zoom in/out functionality, and press AUTO/Auto  
Sync  to restore the picture to its original size. You can also press   repeatedly until  
it is restored to the original size. 
• Using the OSD menu 
1. Press  MENU/EXIT on the projector or Menu on the remote control and then press  
/  until the  DISPLAY menu is highlighted. 
2. Press  to highlight  Zoom and press MODE/ENTER on the projector or Enter on  
the remote control. The Zoom bar is displayed.
3. Repeat steps 2-4 in the section of Using the remote control above.
The picture can only be navigated after the picture is magnified. You can further magnify the  picture while searching for details.
Selecting the aspect ratio
The aspect ratio is the ratio of the image  width to the image height. Most analog TV and  computers are in 4:3 ratio,  and digital TV and DVDs are usually in 16:9 ratio. 
With the advent of digital signal processing,  digital display devices like this projector can  dynamically stretch and scale the image output to  a different aspect than that of the image  input signal.  
To change the projected image ratio (n o matter what aspect the source is): 
• Using the remote control 
1. Press  Aspect to show the current setting. 
2. Press  Aspect repeatedly to select an aspect ratio to suit the format of the video signal  
and your display requirements.
• Using the OSD menu
1. Press  MENU/EXIT on the projector or Menu on the remote control and then press  
/  until the  DISPLAY menu is highlighted. 
2. Press  to highlight  Aspect Ratio. 
3. Press  /  to select an aspect ratio to  suit the format of the video signal and your  
display requirements. 
						

							31
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active  areas. OSD menus can be displayed on those unused black areas.
1. Auto: Scales an image proportionally to fit the  
projectors native reso lution in its horizontal  
width. This is suitable for the incoming image 
which is neither in 4:3 nor 16:9 and you want to 
make most use of the screen without altering the 
images aspect ratio. 
2. 4:3: Scales an image so that it is displayed in the  
center of the screen with a 4:3 aspect ratio. This 
is most suitable for 4:3 images like computer 
monitors, standard definition TV and 4:3 aspect 
DVD movies, as it displays  them without aspect  
alteration. 
3. 16:9: Scales an image so that it is displayed in  
the center of the screen with a 16:9 aspect ratio. 
This is most suitable for images which are 
already in a 16:9 aspect , like high definition TV,  
as it displays them wi thout aspect alteration. 
4. 16:10 (PJD6553w only): Scales an image so that  
it is displayed in the cente r of the screen with a  16:10 aspect ratio. This is most suitable for images  
which are already in a 16:10 aspect, as it displays  
them without aspect alteration
16:10 picture
15:9 picture
4:3 picture
16:9 picture
16:10 picture 
						

							32
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture  modes so that you can choose one to suit your operating environment and input signal picture type. 
To select an operation mode that suits your need, you  can follow one of the following steps. 
• Press  MODE/ENTER on the projector or Color  
Mode  on the remote control repeatedly until your  
desired mode is selected.
•Go to the  PICTURE > Color Mode menu and  
press  /  to select a desired mode.
Picture modes for differ ent types of signals
The picture modes available for different types of signals are listed below. 
PC input signals: D-Sub / Comp. 1/2 (analog RGB) 
1. Brightest mode: Maximizes the brightness of the projected image. This mode is  
suitable for environments where extra-high  brightness is required, such as using the  
projector in well lit rooms.
2. PC mode: Is designed for presentations under daylight environment to match PC and  
notebook coloring.
3. ViewMatch mode: Switches between high brightness performance and accurate color  
performance. 
4. Movie mode: Is appropriate for playing colorful movies, video clips from digital  
cameras or DVs through the PC input for best  viewing in a blackened (little light)  
environment.
5. Dynamic PC mode: Is designed for presentations under daylight environment to  
match PC and notebook coloring. In addition,  the projector will optimize the image  
quality using the dynamic PC  function in accordance with the projected contents.
It takes the projector several minutes after it is turned on or resumed to initiate dynamic PC  function, so that the image contrast can be enhanced. 
6. Dynamic Movie mode: Is appropriate for playing colorful movies, video clips from  
digital cameras or DVs through the PC input  for best viewing in a blackened (little  
light) environment. In addition, the project or will optimize the image quality using the  
dynamic Movie function in accordan ce with the projected contents.
It takes the projector several minutes after it is turned on or resumed to initiate dynamic Movie  function, so that the image contrast can be enhanced. 
7. User 1/User 2 mode: Recalls the settings customized based on the current available  
picture modes. See  Setting the User 1/User 2 mode on page 33 for details. 
Video input signals: S-Video, Vide o, D-Sub / Comp. 1/2 (YPbPr) / HDMI 
1. Brightest mode: Optimized for daylight viewing, with living room level ambient  
brightness.
2. Gaming mode: Suitable for all types of entertainment media, including gaming and  
movies.
ZOOM
TEM P LMMPMODE ENTER AUTOSOURCEMENU EXIT
TEMP LMMPMODE ENTERSOURCEMENUEXITAUTO 
						

							33
3.ViewMatch mode: Switches between high brightness performance and accurate color  
performance.
4. Movie mode: Is suitable for enjoying dark movies or DVD movies best viewed in a  
blackened (little light) home cine ma or lounge room environment. 
5. Dynamic Movie mode: Is suitable for enjoying dark movies or DVD movies best  
viewed in a blackened (little light) home  cinema or lounge room environment. In  
addition, the projector will optimize th e image quality using the dynamic Movie  
function in accordance with the projected contents.
It takes the projector several minutes after it is  turned on or resumed to initiate dynamic Movie  function, so that the image contrast can be enhanced. 
6. User 1/User 2 mode: Recalls the settings customized based on the current available  
picture modes. See  Setting the User 1/User 2 mode on page 33 for details.
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable  for your need. You can use one of the picture modes (except the  User 1/User 2) as a starting  point and customize the settings. 
1. Press  MENU/EXIT on the projector or Menu on the remote control to open the On- 
Screen Display (OSD) menu.
2. Go to the  PICTURE > Color Mode menu. 
3. Press  /  to select  User 1 or User 2. 
4. Press   to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the Color Mode  sub-menu item.
5. Press  /  to select a picture mode  that is closest to your need. 
6. Press   to select a sub-menu item to be changed and adjust the value with  / .  
See  Fine-tuning the image quality in user modes below for details. 
7. When all settings have been done, highlight  Save Settings and press MODE/ENTER  
on the projector or  Enter on the remote control to store the settings. 
8. The confirmation message  Setting Saved is displayed.
Using Screen Color
In the situation where you are projecting onto a colored surface such as a painted wall which  may not be white, the  Screen Color feature can help correct the projected picture’s colors to  prevent possible color difference between  the source and projected pictures. 
To use this function, go to the  DISPLAY > Screen Color menu and press  /  to select a  color which is closest to the color of the pr ojection surface. There are several precalibrated  colors to choose from:  Whiteboard, Greenboard, and Blackboard.
This function is only available when a PC type input signal is selected.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available  when  User 1 or User 2 mode is selected. You can make adjustments to these functions  based on your needs. 
						

							34 
Adjusting Brightness
Highlight the  PICTURE > Brightness menu and press  /. 
The higher the value, the br ighter the image. And the  lower the setting, the darker  the image. Adjust this  control so the black areas of the image appear just as black and that detail in  the dark areas is visible.
Adjusting Contrast
Highlight the PICTURE > Contrast menu and press  / . 
The higher the value, the great er the contrast. Use this  to set the peak white level after you have previously adjusted the  Brightness setting to suit your selected  input and viewing environment.
Adjusting Color
Highlight the  PICTURE > Color menu and press  / . 
Lower setting produces less saturated colors. If  the setting is too high, colors on the image  will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight the  PICTURE > Tint menu and press  / . 
The higher the value, the more reddish the pict ure becomes. The lower the value, the more  greenish the picture becomes.
Adjusting Sharpness
Highlight the  PICTURE > Sharpness menu and press  / . 
The higher the value, the sharper the picture b ecomes. The lower the value, the softer the  picture becomes.
Adjusting Brilliant Color
Highlight the  PICTURE > Brilliant Color menu and press  / . 
This feature utilizes a new co lor-processing algorithm and system level enhancements to  enable higher brightness while providing truer,  more vibrant colors in the projected picture.  It enables a greater than 50% brightness incr ease in mid-tone images, which are common in  video and natural scenes, so the projector reprodu ces images in realistic and true colors. If  you prefer images with that quality, select  On. If you don’t need it, select Off. 
When  Off is selected, the Color Temperature function is not available.
Selecting a Color Temperature
Highlight the PICTURE > Color Temperature menu and press  / . 
The options available for color temperature*  settings vary according to the signal type  selected. 
1. T1: With the highest color temperature, T1 makes the image appear the most bluish  
white than other settings.
2. T2: Makes images appear bluish white. 
3. T3: Maintains normal colorings for white. 
4. T4: Makes images appear reddish white.
+50+30 +70
0-30 +30 
						

							35
*About color temperatures: 
There are many different shades that are cons idered to be white for various purposes. One  of the common methods of representing white co lor is known as the “color temperature”. A  white color with a low color temperature appear s to be reddish white. A white color with a  high color temperature appears to have more blue in it.
Color Management
Only in permanent installations with controlled  lighting levels such as boardrooms, lecture  theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allo w for more accurate color reproduction, should  you require it. 
If you have purchased a test disc which contains  various color test patterns and can be used  to test the color presentation on monitors, TV s, projectors, etc., you can project any image  from the disc on the screen and enter the  Color Management menu to make adjustments. 
To adjust the settings: 
1. Go to the  DISPLAY menu and highlight Color Management. 
2. Press  MODE/ENTER on the projector or Enter on the remote control and the Color  
Management  page is displayed. 
3. Highlight  Primary Color and press  /  to select a color from among Red, Yellow,  
Green, Cyan, Blue, or Magenta. 
4. Press  to highlight  Hue and press  /  to select its range. Increase in the range  
will include colors consisted of more  proportions of its two adjacent colors. 
Please refer to the illustration to the right for  
how the colors relate to each other. 
For example, if you select Red and set its  
range at 0, only pure red in the projected 
picture will be select ed. Increasing its range  
will include red close to yellow and red close 
to magenta.
5. Press  to highlight  Saturation and adjust  
its values to your preference by pressing  / 
. Every adjustment made will reflect to the  
image immediately. 
For example, if you select Red and set its  
value at 0, only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less  saturated colors; a setting of “0” removes that  color from the image entirely. If the saturation  is too high, that color will be overpowering and unrealistic.
6. Press  to highlight  Gain and adjust its values to your preference by pressing  / 
. The contrast level of the primary colo r you select will be affected. Every  
adjustment made will reflect  to the image immediately.  
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press  MENU/EXIT on the projector or Exit on the remote control to exit and save the  
settings.
RED 
BLUE 
GREEN Yellow 
Cyan Magenta