ViewSonic Pjd6531w Projector User Manual

 EN-8
Rear View 
Connection ports
AC power socket
Kensington lock
Rear IR remote control sensor
Ventilation holes (exhaust)
Security bar
Bottom View
Ceiling mount (M4*6)
Tilt-adjustment feet
13245
6
1223456
2
1
70.0mm90.0mm
143.0mm
122
„This projector can be used with a ceiling mount for support. The ceiling mount is
not included in the package.
„Contact your dealer for information to mount the projector on a ceiling. 

EN-9
Using the Product
Control Panel
LED
Button Function
Power (Power LED indicator)
Refer to “LED Indicator Messages”.
TEMP (Temperature LED indicator)
Refer to “LED Indicator Messages”.
LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages”.
 /Keystone
Manually correct distorted images resulting from an angled projection.
Four directional buttons
Use four directional buttons to select items or make adjustments to your  selection.
ENTER
Enter to sub-menu and confirm the menu selection.
SOURCE...

 EN-10
Connection Ports
LAN
For network control.
USB
This connector is for firmware update and mouse function support.
HDMI
Connect HDMI output from video equipment to this jack.
VIDEO
Connect composite video output from video equipment to this jack.
S-VIDEO
Connect S-Video output from video equipment to this jack.
MONITOR OUT
Connect to a computer display, etc.
AUDIO OUTConnect to a speaker or other audio input equipment.
COMPUTER IN 1Connect image input signal (analog RGB or component) to this jack....

EN-11
Remote Control
POWER
Turn the projector on or off.
VGA1
Select analog RGB signal from 
COMPUTER IN 1 terminal.
Source
Manually select an input source by
sequence.
Enter
Confirmed selections.
Keystone+ / -
Adjust image distortion caused by
tilting the projector.
ViewM
Switch in between high brightness 
performance or Accuracy color 
performance.
Freeze
Press “Freeze” to pause the screen 
image. Press again to cancel the 
freeze function.Four directional buttons
Use four directional buttons to select...

 EN-12
Installing the Batteries
1. Open the battery cover in the 
direction shown.
2. Install batteries as indicated by the 
diagram inside the compartment.
3. Close the battery cover into 
position.
Caution
„ Risk of explosion if battery is replaced by an incorrect type.
„ Dispose of used batteries according to the instructions.
„ 
Make sure the plus and minus terminals are correctly aligned when loading a battery.
„Keep the batteries out of the reach of children. There is a danger of death by...

EN-13
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
„Operating the projector from
the front
„Operating the projector from 
the rear
1015
7m5m
5m
10 15
7m5m
5m
„Do not point the laser directly to the peoples eyes (especially small children). 
There is a danger of injury to the eyes.
„The remote control may not operate when there is sunlight or other strong
light such as a fluorescent lamp shining on the remote sensor.
„Operate the remote control from...

 EN-14
Installation
Connecting the Projector
USB Cable Composite Video Cable
VGA Cable (D-Sub to D-Sub) S-Video Cable
RS-232 Cable Internet Cable
Audio Cable HDMI Cable
VGA (D-Sub) to HDTV (RCA) Cable16
27
38
49
5
2214
Desktop type Laptop type
23
5567
8
4
WPG-350
49
„When connecting cable, power cords of both projector and external equipment 
should be disconnected from AC outlet.
„The figure above is a sample connection. This does not mean that all of these 
devices can or must be connected...

EN-15
Powering On/Off the Projector
Powering On the Projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press   button to turn on the projector.
The projector takes a minute or so to warm up. 
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically
detects your source.
„If you are connecting multiple sources to the projector simultaneously, press
the SOURCE button on the control panel or the Source button on...

 EN-16
Adjusting the Projector
Adjusting the Projector Height
The projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image:
1. To raise or lower the image, press the elevator button and raise or lower the front
of the projector. Release the button to lock the adjustment.
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the 
height.
Adjusting the Projector Zoom and Focus
1. Focus the image by rotating the focus ring. A still image...

EN-17
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
Screen sizeDiagonal 16 : 10 Screen
Wide Tele
Projection distance Projection distance
minchminch
1.02m / 40” 1.23 48.6  1.01 39.7
1.27m / 50” 1.56 61.3 1.27 50.0
1.52m / 60” 1.88 74.0 1.53 60.3
1.78m / 70” 2.20 86.6 1.80 70.7
2.03m / 80” 2.52 99.3 2.06 81.0
2.29m / 90” 2.84 112.0 2.32 91.4
2.54m / 100” 3.17 124.7 2.58 101.7
3.05m / 120” 3.81 150.0 3.11 122.4
3.81m / 150” 4.78...