ViewSonic Pjd6253 Projector User Manual
Have a look at the manual ViewSonic Pjd6253 Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 617 ViewSonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
6 Projector exterior view 1. External control panel (See Projector on page 7 for details.) 2. Lamp cover 3. Vent (heated air exhaust) 4. Quick-release button 5. Lens cover 6. Focus and Zoom ring 7. Front IR remote sensor 8. Projection lens 9. Type B USB port 10. RJ45 LAN input port 11. RS-232 control port 12. HDMI port 13. RGB signal output socket 14. RGB (PC)/Component video (YPbPr/YCbCr) signal input socket-1/2 15. S-Video input socket 16. Video input socket 17. Audio signal input socket Audio signal output socket 18. Kensington anti-theft lock slot 19. AC power cord inlet 20. Rear adjuster foot 21. Quick-release foot 22. Security bar Connects a commercially available theft prevention cable. Warning • THIS APPARATUS MUST BE EARTHED. • When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug. Front/upper side 1 2 3 4 5 6 7 8 PJD6223/PJD6253/ PJD6553w 18 21 20 PJD5126 TYPE B USB COMPUTER IN 2RS-232MONITOR OUT COMPUTER IN 1 S-Viseo Video Audio in Audio out 91012131516171114 9151617111413 19 22 Rear/lower side
7 Controls and functions Projector 1. Focus ring Adjusts the focus of the projected image. 2. Zoom ring Adjusts the size of the image. 3. Keystone/Arrow keys ( / Up, / Down) Manually corrects distorted images resulting from an angled projection. 4. Left/Blank Hides the screen picture. 5. POWER indicator light Lights up or flashes when the projector is under operation. POWER Toggles the projector between standby mode and on. 6. SOURCE Displays the source selection bar. 7. Top IR remote sensor Not available for the PJD5126. 8. MENU/EXIT Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings. 9. Right/ Activates panel key lock. When the On-Screen Display (OSD) menu is activated, the #3, #4, and #9 keys are used as directional arrows to select the desired menu items and to make adjustments. 10. LAMP indicator light Indicates the status of the lamp. Lights up or flashes when the lamp has developed a problem. 11 . A U T O Automatically determines the best picture timings for the displayed image. 12. TEMPerature indicator light Lights up red if the projectors temperature becomes too high. 13. MODE/ENTER Selects an available picture setup mode. Enacts the selected On-Screen Display (OSD) menu item. ZOOM TEMPLMMPMODEENTERAUTOSOURCEMENUEXIT 12 3 45 63 8910 1213 11 7 II
8 Remote control To use the remote mouse control keys (Page Up, Page Down, , and ), see Using the remote mouse control on page 10 for details. 1. POWER Toggles the projector between standby mode and on. 2. Source selection keys (VGA 1/VGA 2/Video) Selects an input source for display. Video/ Selects Video, S-Video or HDMI source for display. Performs the same function as the right mouse button when the mouse mode is activated. 3. Source Displays the source selection bar. 4. Keystone keys ( / ) Manually corrects distorted images resulting from an angled projection. 5. // / Selects the desired menu items and makes adjustments. 6. Enter/ Enacts the selected On-Screen Display (OSD) menu item. Performs the same function as the left mouse button when the mouse mode is activated. 7. My Button Allows user to define a short cut key on the remote control, and the function item is selected in OSD menu. 8. Menu Turns on the On-Screen Display (OSD) menu. 9. Mouse Switches between the normal and mouse modes. Page Up , Page Down, , : active after pressing Mouse. An icon appears on the screen to indicate the activation of the mouse mode. 1 2 3 5 8 9 4 18 19 14 20 21 22 23 24 6 10 12 16 13 17 11 15 74 1 2 3 5 8 9 4 25 19 14 20 21 22 23 24 6 10 16 11 17 18 15 74 12 PJD5126/PJD6223 PJD6253/PJD6553w II
9 Remote control code The projector can be assigned to two different remote control codes, A or B. When several adjacent projectors are in operation at the sa me time, switching the remote control codes can prevent interference from other remote controls. Set the remote control code for the projector first before changing that for the remote control. To switch the code for the projector, select A or B in the SYSTEM SETUP: Advanced > Remote Control Code menu. To switch the code for th e remote control, press PgUp and PgDn buttons on the remote control together for 5 seconds or mo re. The initial code is set to A. If different codes are set on the projector and remote control, there will be no response from the remote control. When that happens, swit ch the code for the remote control again. 10. Lock Activates panel key lock. 11. Aspect Selects the display aspect ratio. 12. Magnify Displays the zoom bar that magnifies or reduces the projected picture size. 13. Info Displays the INFORMATION menu. 14. Freeze Freezes the projected image. 15. Pattern Displays embedded test pattern. 16. Blank Hides the screen picture. 17. Smart Eco Decreases the power consumption of the lamp by up to 70%. It takes the projector several minutes after it is turned on or resumed to initiate the function. 18. Auto Sync Automatically determines the best picture timings for the displayed image. 19. Exit Goes back to previous OSD menu, exits and saves menu settings. 20. PgUp (Page Up)/PgDn (Page Down) Operates your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint) when the mouse mode is activated. 21. Volume keys (+, -) Magnifies or reduces the volume level. 22. Toggles the projector audio between on and off. 23. Color Mode Selects an available picture setup mode. 24. Timer Displays the presentation timer settings menu. 25. Laser Emits visible laser pointer light for presentation purposes. Operating the Laser pointer The Laser Pointer is a presentation aid for professionals. It emits red colored light when you press it and the indicator lights up red. The laser beam is visible. It is necessary to press and hold LASER for continuous output. The laser pointer is not a toy. Parents should be mindful of the dangers of laser energy and keep this remote control out of the reach of children. Do not look into the laser light window or shine the laser light beam on yourself or others. See the warning messages on the back of the remote control prior to using it.
10 Using the remote mouse control The capability of operating your computer with the remote control gives you more flexibility when delivering presentations. 1. Connect the projector to your PC or notebook with a USB cable prior to using the remote control in place of your computer’s mouse. See Connecting a computer on page 17 for details. 2. Set the input signal to D-Sub / Comp. 1, D-Sub / Comp. 2 or HDMI. 3. Press Mouse on the remote control to switch from the normal mode to the mouse mode. An icon appears on the screen to i ndicate the activation of the mouse mode. 4. Perform the desired mouse controls on your remote control. • To move the cursor on the screen, press / / / . • To left-click, press . • To right-click, press . • To operate your display software program (on a connected PC) which responds to page up/down commands (like Mi crosoft PowerPoint), press PgUp/PgDn. • To return to the normal mode, press Mouse again or other keys except for the mouse related multi-function keys. Remote control effective range Infra-Red (IR) remote control sensors are locat ed on the front and the top of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projectors IR remote control sensors to func tion correctly. The distance between the remote control and the sensors should not exceed 8 meters (~ 26 feet). Make sure that there are no obstacles between the remote control and the IR sensors on the projector that might obstruct the infra-red beam. • Operating the projector from the front A pp r ox . 15 ° A p p r o x . +1 5 ° • Operating the projector from the top
11 Replacing the remote control batteries 1. To open the battery cover, turn the remote control over to view its back, push on the finger grip on the cover and slid e it in the direction of the arrow as illustrated. The cover will slide off. 2. Remove any existing batteries (if necessa ry) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive (+) goes to positive and negative (-) goes to negative. 3. Refit the cover by aligning it with the base and sliding it back down into position. Stop when it clicks into place. • Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car. • Replace only with the same or equivalent type recommended by the battery manufacturer. • Dispose of the used batteries according to the manufacturers instructions and local environment regulations for your region. • Never throw the batteries into a fire. There may be danger of an explosion. • If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control from possible battery leakage.
12 Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the locati on and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of four possible installation locations: 1. Front Table Select this location with the projector placed near the floor in front of the screen. This is the most common way to position th e projector for quick setup and portability. 2. Front Ceiling Select this location with the projector suspended upside-down from the ceiling in front of the screen. Purchase the projector ceiling mount kit from your dealer to mount your projector on the ceiling. Set Front Ceiling in the SYSTEM SETUP: Basic > Projector Position menu after you turn the projector on. 3. Rear Ceiling Select this location with the projector suspended upside-down from the ceiling behind the screen. Note that a special rear projection screen and the projector ceiling mounting ki t are required for this installation location. Set Rear Ceiling in the SYSTEM SETUP: Basic > Projector Position menu after you turn the projector on. 4. Rear Table Select this location with the projector placed near the floor behind the screen. Note that a special rear projection screen is required. Set Rear Table in the SYSTEM SETUP: Basic > Projector Position menu after you turn the projector on.
13 Projection dimensions Refer to Dimensions on page 65 for the center of lens dimensions of this projector before calculating the appropriate position. The screen mentioned below refers to the projection screen usually consisting of a surface and a support structure PJD5126/PJD6223/PJD6253 PJD5126/PJD6223 (a) Screen Size [inch (m)] 4:3 image on a 4:3 Screen 16:9 image on a 4:3 Screen (b) Projection distance [m (inch)] (c) Image height [cm (inch)] (d) Vertical offset [cm (inch)] (b) Projection distance [m (inch)] (c) Image height [cm (inch) (d) Vertical offset [cm (inch)] min. max. min. max. 40(1.0) 1.5 (60) 1.7 (66) 61 (24) 3 (1.2) 1.5 (60) 1.7 (66) 46 (18) 10.7 (4.2) 50(1.3) 1.9 (75) 2.1 (82) 76 (30) 4 (1.5) 1.9 (75) 2.1 (82) 57 (23) 13.3 (5.3) 60(1.5) 2.3 (90) 2.5 (99) 91 (36) 5 (1.8) 2.3 (90) 2.5 (99) 69 (27) 16.0 (6.3) 70(1.8) 2.7 (105) 2.9 (115) 107 (42) 5 (2.1) 2.7 (105) 2.9 (115) 80 (32) 18.7 (7.4) 80(2.0) 3.0 (120) 3.4 (132) 122 (48) 6 (2.4) 3.0 (120) 3.4 (132) 91 (36) 21.3 (8.4) 90(2.3) 3.4 (135) 3.8 (148) 137 (54) 7 (2.7) 3.4 (135) 3.8 (148) 103 (41) 24.0 (9.5) 100(2.5) 3.8 (150) 4.2 (165) 152 (60) 8 (3.0) 3.8 (150) 4.2 (165) 114 (45) 26.7 (10.5) 120(3.0) 4.6 (180) 5.0 (198) 183 (72) 9 (3.6) 4.6 (180) 5.0 (198) 137 (54) 32.0 (12.6) 150(3.8) 5.7 (225) 6.3 (247) 229 (90) 11 (4.5) 5.7 (225) 6.3 (247) 171 (68) 40.0 (15.8) 200(5.1) 7.6 (300) 8.4 (330) 305 (120) 15 (6.0) 7.6 (300) 8.4 (330) 229 (90) 53.3 (21.0) 250(6.4) 9.51 (375) 10.5 (412) 381 (150) 19 (7.5) 9.51 (375) 10.5 (412) 286 (113) 66.7 (26.3) 300(7.6) 11.4 (450) 12.6 (495) 457 (180) 23 (9.0) 11.4 (450) 12.6 (495) 343 (135) 80.0 (31.5) (a) (c) (b) (e) (f) (d) (a) (d) (b) (e) (f) (c) (a) (d) (c) (b) (e) (f) (a) (c) (b) (e) (f) (d) (f): Center of lens (e): Screen • 4:3 image on a 4:3 screen • 16:9 image on a 4:3 screen
14 PJD6253 (a) Screen Size [inch (m)] 4:3 image on a 4:3 Screen 16:9 image on a 4:3 Screen (b) Projection distance [m (inch)] (c) Image height [cm (inch)] (d) Vertical offset [cm (inch)] (b) Projection distance [m (inch)] (c) Image height [cm (inch) (d) Vertical offset [cm (inch)] min. max. min. max. 40(1.0) 1.2 (48) 1.6 (63) 61 (24) 5 (1.8) 1.2 (48) 1.6 (63) 46 (18) 12.2 (4.8) 50(1.3) 1.5 (61) 2.0 (79) 76 (30) 6 (2.3) 1.5 (61) 2.0 (79) 57 (23) 15.2 (6.0) 60(1.5) 1.8 (73) 2.4 (94) 91 (36) 7 (2.7) 1.8 (73) 2.4 (94) 69 (27) 18.3 (7.2) 70(1.8) 2.2 (85) 2.8 (110) 107 (42) 8 (3.2) 2.2 (85) 2.8 (110) 80 (32) 21.3 (8.4) 80(2.0) 2.5 (97) 3.2 (126) 122 (48) 9 (3.6) 2.5 (97) 3.2 (126) 91 (36) 24.4 (9.6) 90(2.3) 2.8 (109) 3.6 (142) 137 (54) 10 (4.1) 2.8 (109) 3.6 (142) 103 (41) 27.4 (10.8) 100(2.5) 3.1 (121) 4.0 (157) 152 (60) 11 (4.5) 3.1 (121) 4.0 (157) 114 (45) 30.5 (12.0) 120(3.0) 3.7 (145) 4.8 (189) 183 (72) 14 (5.4) 3.7 (145) 4.8 (189) 137 (54) 36.6 (14.4) 150(3.8) 4.6 (182) 6.0 (236) 229 (90) 17 (6.8) 4.6 (182) 6.0 (236) 171 (68) 45.7 (18.0) 200(5.1) 6.2 (242) 8.0 (315) 305 (120) 23 (9.0) 6.2 (242) 8.0 (315) 229 (90) 61.0 (24.0) 250(6.4) 7.7 (303) 10.0 (394) 381 (150) 29 (11.3) 7.7 (303) 10.0 (394) 286 (113) 76.2 (30.0) 300(7.6) 9.2 (363) 12.0 (472) 457 (180) 34 (13.5) 9.2 (363) 12.0 (472) 343 (135) 91.4 (36.0)
15 PJD6553w There is 3% tolerance among these numbers due to optical component variations. It is recommended that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projectors optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location. (a) Screen Size [inch (m)] 16:10 image on a 16:10 Screen 16:10 image on a 4:3 Screen (b) Projection distance [m (inch)] (c) Image height [cm (inch)] (d) Vertical offset [cm (inch)] (b) Projection distance [m (inch)] (c) Image height [cm (inch) (d) Vertical offset [cm (inch)] min. max. min. max. 30(0.8) 0.78 (31) 1.02 (40) 40 (16) 1 (0.4) 0.74 (36) 0.96 (38) 38 (15) 3.8 (1.5) 40(1.0) 1.05 (41) 1.36 (54) 54 (21) 1 (0.5) 0.99 (48) 1.28 (50) 51 (20) 5.1 (2.0) 50(1.3) 1.31 (51) 1.70 (67) 67 (26) 2 (0.7) 1.23 (61) 1.60 (63) 64 (25) 6.4 (2.5) 60(1.5) 1.57 (62) 2.04 (80) 81 (32) 2 (0.8) 1.48 (73) 1.92 (76) 76 (30) 7.6 (3.0) 70(1.8) 1.83 (72) 2.38 (94) 94 (37) 2 (0.9) 1.73 (85) 2.24 (88) 89 (35) 8.9 (3.5) 80(2.0) 2.09 (82) 2.72 (107) 108 (42) 3 (1.1) 1.97 (97) 2.57 (101) 102 (40) 10.2 (4.5) 90(2.3) 2.35 (93) 3.06 (120) 121 (48) 3 (1.2) 2.22 (109) 2.89 (114) 114 (45) 11.4 (4.5) 100(2.5) 2.61 (103) 3.40 (134) 135 (53) 3 (1.3) 2.47 (121) 3.21 (126) 127 (50) 12.7 (5.0) 120(3.0) 3.14 (124) 4.08 (161) 162 (64) 4 (1.6) 2.96 (145) 3.85 (151) 152 (60) 15.2 (6.0) 150(3.8) 3.92 (154) 5.10 (201) 202 (79) 5 (2.0) 3.70 (182) 4.81 (189) 191 (75) 19.1 (7.5) 200(5.1) 5.23 (206) 6.80 (268) 269 (106) 7 (2.6) 4.93 (242) 6.41 (252) 254 (100) 25.4 (10.0) 250(6.4) 6.54 (257) 8.50 (335) 337 (132) 8 (3.3) 6.17 (303) 8.02 (316) 318 (125) 31.8 (12.5) 300(7.6) 7.84 (309) 10.20 (401) 404 (159) 10 (4.0) 7.40 (363) 9.62 (379) 381 (150) 38.1 (15.0) (a) (c) (b) (e) (f) (d) (a) (c) (b) (e) (f) (d) (a) (c) (b) (e) (f) (d) (f): Center of lens (e): Screen • 16:10 image on a 16:10 screen • 16:10 image on a 4:3 screen (a) (d) (c) (b) (e) (f)