ViewSonic Pjd6223 Projector Specifications

							36
*About color temperatures:
There are many different shades that are considered to be white for various purposes. One 
of the common methods of representing white color is known as the “color temperature”. A 
white color with a low color temperature appears to be reddish white. A white color with a 
high color temperature appears to have more blue in it.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allow for more accurate color reproduction, should 
you require it.
If you have purchased a test disc which contains various color test patterns and can be used 
to test the color presentation on monitors, TVs, projectors, etc., you can project any image 
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1. Go to the DISPLAY menu and highlight Color Management.
2. Press MODE/ENTER on the projector or Enter on the remote control and the Color 
Management page is displayed.
3. Highlight Primary Color and press  /  to select a color from among Red, Yellow, 
Green, Cyan, Blue, or Magenta.
4. Press  to highlight Hue and press  /  to select its range. Increase in the range 
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for 
how the colors relate to each other.
For example, if you select Red and set its 
range at 0, only pure red in the projected 
picture will be selected. Increasing its range 
will include red close to yellow and red close 
to magenta.
5. Press  to highlight Saturation and adjust 
its values to your preference by pressing  /
. Every adjustment made will reflect to the 
image immediately.
For example, if you select Red and set its 
value at 0, only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less 
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation 
is too high, that color will be overpowering and unrealistic.
6. Press  to highlight Gain and adjust its values to your preference by pressing  /
. The contrast level of the primary color you select will be affected. Every 
adjustment made will reflect to the image immediately. 
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press MENU/EXIT on the projector or Exit on the remote control to exit and save the 
settings.
RED
BLUEGREEN Yellow
Cyan
Magenta 
						

							37
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve 
better time management when giving presentations. Follow these steps to utilize this 
function:
1. Press Timer on the remote control to access the Presentation Timer menu or go to 
the SYSTEM SETUP: Advanced > Presentation Timer menu and press MODE/
ENTER to display the Presentation Timer page.
2. Highlight Timer Period and decide the time period by pressing  / . The length of 
time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-
minute increments.
If the timer is already on, the timer will restart whenever the Timer Period is reset.
3. Press  to highlight Timer Display and choose if you want the timer to show up on 
the screen by press
ing /.
4. Press  to highlight Timer Position and set the timer position by pressing  /.
5. Press  to highlight Timer Counting Direction and select your desired counting 
direction by pressing  / .
6. Press  to highlight Sound Reminder and decide if you want to activate sound 
reminder by pressing  / . If you select On, a double beep sound will be heard at 
the last 30 seconds of counting down/up, and a triple beep sound will be produced 
when the timer is up.
7. To activate the presentation timer, press   and press  /  to highlight Start 
Counting and press MODE/ENTER.
8. A confirmation message displays. Highlight Ye s and press MODE/ENTER on the 
projector or remote control to confirm. You will see the message “Timer is On” 
displaying on the screen. The timer starts counting when the timer is on.
To cancel the timer, perform the following steps:
1. Go to the SYSTEM SETUP: Advanced > Presentation Timer menu and highlight 
Off. Press MODE/ENTER. A confirmation message displays.
2. Highlight Yes and press MODE/ENTER to confirm. You will see the message 
“Timer is Off” displaying on the screen.
SelectionDescription
AlwaysDisplays the timer on screen throughout the presentation 
time.
1 min/2 min/3 min  Displays the timer on screen in the last 1/2/3 minute(s).
Never Hides the timer throughout the presentation time.
Top-Left Bottom-Left Top-Right Bottom-Right
SelectionDescription
Count Up Increases from 0 to the preset time.
Count Down Decreases from the preset time to 0. 
						

							38
Hiding the image
In order to draw the audiences full attention to the 
presenter, you can use  on the projector or Blank on 
the remote control to hide the screen image. Press any 
key on the projector or remote control to restore the 
image. The word BLANK appears at the lower right 
corner of the screen while the image is hidden.
You can set the blank time in the 
SYSTEM SETUP: 
Basic > Blank Timer menu to let the projector return 
the image automatically after a period of time when 
there is no action taken on the blank screen. 
Once Blank is pressed, the projector enters Economic 
mode automatically.
CAUTION
Do not block the projection lens from projecting as this 
could cause the blocking object to become heated and 
deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from 
being changed accidentally (by children, for example). When the Panel Key Lock is on, no 
control keys on the projector will operate except POWER.
1. Press   on the projector or remote control, or go 
to the 
SYSTEM SETUP: Basic > Panel Key 
Lock menu
, and select On by pressing  /  on 
the projector or remote control. 
2. A confirmation message is displayed. Select Yes 
to confirm.
To release panel key lock, press and hold   for 3 
seconds on the projector.
You can also use the remote control to enter the 
SYSTEM SETUP: Basic > Panel Key Lock menu and 
press /  to select Off.
• Keys on the remote control are still functional when 
panel key lock is enabled.
• If you press  POWER to turn off the projector without 
disabling panel key lock, the projector will still be in 
locked status the next time it is turned on.
ZOOM
TEMP
LMMPMODE
ENTERAUTOSOURCEPOWERMENU
EXIT
TEMP
LMMPMODE
ENTERAUTOSOURCEPOWERMENU
EXIT
II
ZOOM
TEMP
LMMPMODE
ENTERAUTOSOURCEPOWERMENU
EXIT
TEMPMODE
ENTERSOURCEMENU
EXITPOWERAUTOLMMP
II 
						

							39
Freezing the image
Press Freeze on the remote control to freeze the 
image. The word FREEZE will be displayed in the 
upper left corner of the screen. To release the 
function, press any key on the projector or remote 
control.
Even if an image is frozen on the screen, the pictures 
are running on the video or other device. If the 
connected devices have active audio output, you will 
still hear the audio even though the image is frozen 
on screen.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500 
m–3000 m above sea level, and temperature is between 0°C–35°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature 
is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under 
such a condition.
To activate the High Altitude Mode:
1. Press MENU/EXIT on the projector or Menu on 
the remote control and then press  /  until the 
SYSTEM SETUP: Advanced menu is 
highlighted.
2. Press  to highlight High Altitude Mode and 
press /  to select On. A confirmation 
message is displayed.
3. Highlight Yes and press MODE/ENTER on the projector or Enter on the remote 
control.
Operation under High Altitude Mode may cause a higher decibel operating noise level 
because of increased fan speed necessary to improve overall system cooling and 
performance.
If you use this projector under other extreme conditions excluding the above, it may display 
auto shut-down symptoms, which is designed to protect your projector from over-heating. 
In cases like this, you should switch to High Altitude Mode to solve these symptoms. 
However, this is not to state that this projector can operate under any and all harsh or 
extreme conditions.
We recommend you use the High Altitude 
mode by selecting it whenever your 
environment is higher than 1500 m.
Do you want to turn High Altitude Mode 
ON?
YesNoNotice 
						

							40
Creating your own startup screen
This function is only available for the PJD6223/RC6/SD7/PJD6253/PV731/FP586/PJD6553w 
series.
In addition to selecting the projector preset startup screen from among ViewSonic logo, 
Black or Blue screen, you can make your own startup screen that is a picture projected from 
your computer or video source.
To create your own startup screen, project the picture you want to use as your startup screen 
from either a computer or video source. The rest of the steps are as follows.
1. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the SYSTEM SETUP: Basic menu is highlighted.
2. Press  to highlight Screen Capture and press MODE/ENTER on the projector or 
Enter on the remote control.
3. A confirmation message is displayed. Press MODE/ENTER on the projector or 
Enter on the remote control again.
4. The message Screen Capturing... is displayed while the projector is processing the 
picture. Please wait.
5. If the action is successful, you see the message Capture Succeeded on the screen. 
The captured picture is saved as Screen Capture.
6. To view the captured picture displayed as the startup screen, set Screen Capture in 
the SYSTEM SETUP: Basic > Splash Screen menu and restart the projector.
In the unlikely event that the capturing action fails, change your target picture. When the 
resolution of the input signal is higher than the projector’s native display resolution (See 
Projector specifications on page 63 for details.), the capture action may fail. When it 
happens, please set the resolution of the input signal under native resolution and try again. 
						

							41
Controlling the projector through a LAN 
environment
This function is only available for the PJD6223/RC6/SD7/PJD6253/PV731/FP586/PJD6553w 
series.
The projector supports Crestron® software. With correct settings for the LAN Control 
Settings menu, you can manage the projector from a computer using a web browser when 
the computer and the projector are properly connected to the same local area network. 
Configuring the LAN Control Settings
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector 
and the other end to the RJ45 port.
2. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the SYSTEM SETUP: Basic menu is highlighted.
3. Press  to highlight LAN Control Settings and press MODE/ENTER on the 
projector or Enter on the remote control. The LAN Control Settings page is 
displayed.
4. Press  to highlight DHCP and press  /  to select On.
5. Press  to highlight Apply and press MODE/ENTER on the projector or Enter on 
the remote control.
6. Please wait for around 15 - 20 seconds, and then re-enter the LAN Control Settings 
page. The Projector IP Address, Subnet Mask, Default Gateway, and DNS Server 
settings will be displayed. Note down the IP address displayed in the Projector IP 
Address row.
• If the Projector IP Address still does not appear, contact your network administrator.
• If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, 
Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are 
properly connected and perform the procedures above again.
• If you need to connect to the projector in its standby mode, set Power Saving to Off.
TYPE B
USB
LANRS-232
(An example of connection) 
						

							42 If you are in a non-DHCP environment:
1. Repeat steps 1-3 above.
2. Press  to highlight DHCP and press  /  to select Off.
3. Contact your ITS administrator for information on the Projector IP Address, Subnet 
Mask, Default Gateway, and DNS Server settings.
4. Press   to select the item you want to modify and press MODE/ENTER on the 
projector or Enter on the remote control.
5. Press  /  to move the cursor and the press  /  to enter the value.
6. To save the settings, press MODE/ENTER on the projector or Enter on the remote 
control. If you do not want to save the settings, press MENU/EXIT on the projector 
or Menu on the remote control.
7. Press  to highlight Apply and press MODE/ENTER on the projector or Enter on 
the remote control.
• If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, 
Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are 
properly connected and perform the procedures above again.
• If you wish to connect to the projector in its standby mode, be sure you have selected 
RJ45 and obtained the Projector IP Address, Subnet Mask, Default Gateway, and DNS 
Server information when the projector is on.
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby 
mode, you can use any computer that is on the same local area network to control the 
projector.
• If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
• The screen shots in this manual are for reference only, and may differ from the actual 
design.
1. Enter the address of the projector in the address bar of your browser and press Enter.
2. The main page of the Network Control appears.
3. This page allows you to make adjustments to the AMX and SNMP settings.
4. The Crestron (e-Control) page displays the Crestron e-Control user interface. See 
About Crestron e-Control® on page 43 for details.
4
3 
						

							43
About Crestron e-Control®
1. The Crestron e-Control® page provides a variety of virtual keys to control the 
projector or adjust the projected pictures. 
i. These buttons function the same as the ones on the OSD menus or remote control. 
See 2. PICTURE menu on page 51 and Projector on page 8 for details.
ii. To switch between input signals, click on your desired signal.
• The Menu button can also be used to go back to previous OSD menus, exit and save menu 
settings.
• The source list varies according to the connectors available on the projector.
• When you use the projector control panel or remote control to change the OSD menu 
settings, it may take a while for the web browser to synchronize these changes with the 
projector.
2. The tools page allows you to manage the projector, configure the LAN control 
settings and secure access of remote network operation on this projector.
i. This section is only used with the Crestron Control System. Please contact 
Creston or refer to its user manual for setup information.
ii. You can name the projector, keep track of its location and the person in charge of 
it.
i
i
i
ii
You can press 
/ to reveal 
more buttons.
iiv
iii
ii
v
vi 
						

							44
iii. You can adjust the LAN Control Settings.
iv. Once set, access to the remote network operation on this projector has been 
password-protected.
v. Once set, access to the tools page has been password-protected.
• To prevent errors, only input the English alphabet and digits on the tools page.
• After making the adjustments, press the Send button and the data will be saved for the 
projector.
vi. Press Exit to go back to the remote network operation page.
Please pay attention to the limitation of input length (including space and other punctuation 
keys) in the list blow:
Category ItemInput LengthMaximum Number of 
Characters
Crestron ControlIP Address 15
IP ID 2
Port 5
ProjectorProjector Name 10
Location 9
Assigned To 9
Network ConfigurationDHCP (Enabled) (N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User PasswordEnabled (N/A)
New Password 20
Confirm 2
Admin PasswordEnabled (N/A)
New Password 20
Confirm 20 
						

							45
3. The info page displays the information and status of this projector.
4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in 
the upper right corner of the screen. You will be able to deliver messages to 
RoomView™ software administrators/users who connect to the same local area 
network.
For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
PJLink™, SNMP, AMX and Xpanel formats supported
This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details, 
please follow its user guide or website respectively to control and manage projectors.
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned 
on). To use these functions, be sure you have turned on the corresponding menus under 
SYSTEM SETUP: Basic > Standby Settings, and the cable connections are correctly 
made. For the connection methods, see the Connection chapter.
Power Saving
Less than 1W power consumption when Power Saving mode is turned on.
When Power Saving is On, the following settings are not available.
Active VGA Out
Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT 
sockets are correctly connected to devices. The projector outputs the signal received only 
from COMPUTER IN 1. 
Active Audio Out
Selecting On outputs an audio signal when the AUDIO IN 1 and AUDIO OUT sockets are 
correctly connected to devices. The projector outputs the audio signal received only from 
AUDIO IN 1.
LAN Control
Select On when you wish to control the projector over a network when it is in standby 
mode.
Press Exit to 
go back to the 
remote network 
operation page.