ViewSonic Pjd5232 Projector User Manual

							33
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually 
decreases and the lamp becomes more susceptible to breakage. We recommend 
replacing the lamp if a warning message is displayed. Do not attempt to replace the 
lamp yourself. Contact the qualified service personnel for replacement.
Note
• The lamp is extremely hot right after turning off the projector. If you touch the lamp, you 
may scald your finger. When you replace the lamp, wait for at least 45 minutes for the 
lamp to cool down.
• Do not touch the lamp glass at any time. The lamp may explode due to improper 
handling, including the touching of the lamp glass.
• Lamp lifetime may differ from lamp to lamp and according to the environment of use. 
There is no guarantee of the same lifetime for each lamp. Some lamps may fail or 
terminate their lifetime in a shorter period of time than other similar lamps.
• A lamp may explode as a result of vibration, shock or degradation as a result of hours of 
use as its lifetime draws to an end. Risk of explosion may differ according to the 
environment or conditions in which the projector and lamp are being used.
• Wear protective gloves and eyeglasses when fixing or detaching the lamp.
• Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5 
minutes to turn off the projector after powering on.
• Do not operate the lamp in proximity to paper, cloth, or other combustible material nor 
cover it with such materials.
• Do not operate the lamp in an atmosphere containing an inflammable substance, such 
as thinner.
• Thoroughly ventilate the area or the room when operating the lamp in an oxygen 
atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea, dizziness, 
and other symptoms.
• The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside the 
lamp will be exposed. Leave the area immediately if the lamp shatters while being 
operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of 
mercury fumes. Otherwise it could be harmful to user’s health. 
						

							34
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the 
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector.  If the lamp does not turn on after the warm-up period, try 
reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Option > Lamp Setting” menu.
Note
• Dispose the used lamp according to local regulations.
• Ensure that screws are tightened properly. Screws not tightened fully may result in 
injury or accidents.
• Since the lamp is made of glass, do not drop the unit and do not scratch the glass.
• Do not reuse the old lamp. This could cause the lamp to explode.
• Be sure to turn off the projector and unplug the AC power cord before replacing the 
lamp.
• Do not use the projector with the lamp cover removed. 
						

							35
Specifications
Display system Single 0.55" DLP panel
Resolution XGA (1024 x 768 pixels)
Zoom 1.1x
F/No. 1.97 - 2.17
Focal length 21.95 - 24.18mm
Screen size 30” - 300”
Lamp 190W (PJD5232 / PJD5234)
280W (PJD7223)
Input terminal D-Sub 15-pin x 2, S-Video x 1, Video x 1, Audio signal 
input (3.5 mm stereo mini jack) x 2, HDMI x 1 (only for 
PJD5234)
Output terminal D-Sub 15 pin x 1,  Audio signal output (3.5 mm stereo 
mini jack) x 1
Control terminal RS-232 x 1, Type B USB x1 (supports firmware 
upgrade and remote mouse control)
Speaker 2 watt x 1
Video compatibility NTSC, NTSC 4.43
PA L ,  PA L - N ,  PA L  M
SECAM, HDTV (480i/p, 576p, 720p, 1080i/p), 
Composite video
Scanning frequency
Horizontal frequency
Vertical frequency31 - 100 KHz
24 - 120 Hz
Environment Operating:
Temperature: 0°C to 40°C
Humidity: 10%-80%
Storage:
Temperature: -20°C to 60°C
Humidity:30%-85%
Power requirement AC 100-240 V, 50 - 60 Hz, 2.6A
Power consumption 255W (Max.) PJD5232 & PJD5234
360W (Max.) PJD7223
Dimension (W x D x H) 294 x 219 x 113 mm
Weight 2.1 kg (4.6 lb)
Note: Design and Specifications are subject to change without prior notice. 
						

							36
Dimensions
294 mm (W) x 219 mm (D) x 113 mm (H)
Ceiling mount installation
219
11 3294
85
72
15032
40
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm 
						

							37
Appendix
LED Indicator Messages
LED TypeColorStatusMeaning
Power LED Blue Solid Standby mode when green mode is turned 
on.
Te m p  L E D R e d O f f
Lamp LED Red Off
Power LED Blue Flash Standby mode when green mode is turned 
off.
Temp LED Red Off
Lamp LED Red Off
Power LED Blue Flash Powering up
Temp LED Red Off
Lamp LED Red Off
Power LED Blue Solid Normal operation
Temp LED Red Off
Lamp LED Red Off
Power LED Blue Solid Powering down
Temp LED Red Off
Lamp LED Red Off
Power LED Blue Solid If the projector system has some problems 
with its fans, the projector will shut down.
Temp LED Red Flash
Lamp LED Red Flash
Power LED Blue Solid The lamp has reached its end of life and 
must be changed soon. The lamp will 
continue to operate until it fails. Change the 
lamp. If the lamp is off, then the ballast will 
become malfunction. Temp LED Red Off
Lamp LED Red Flash
Power LED Blue Flash 1. Temperature is too high. The lamp will 
turn off. The fan motor is cooling the lamp.
Or
2. The cooling process is not complete after 
the projector is shut down and re-started 
right away. Temp LED Red Flash
Lamp LED Red Off
Power LED Blue Flash The lamp ignition failed. If temperature is 
too high, the fans will cool the lamp. 
Temp LED Red Off
Lamp LED Red Solid 
						

							38
Compatibility Modes
Computer:
Video: 
Resolution H-Sync [KHz] V-Sync [Hz]
640 x 350 37.9 85.0
640 x 480 24.6 50.0
31.5 59.9
37.9 72.8
37.5 75.0
43.3 85.0
61.9 120.0
720 x 400 31.5 70.0
37.9 85.0
800 x 600 31.0 50.0
35.2 56.0
37.9 60.3
48.1 72.0
46.9 75.0
53.7 85.1
76.3 120.0
1024 x 768 48.4 60.0
56.5 70.1
60.0 75.0
68.7 85.0
97.6 120.0
1152 x 864 67.5 75.0
1280 x 768 47.8 60.0
1280 x 960 60.0 60.0
85.9 85.0
1280 x 1024 64.0 60.0
1400 x 1050 65.3 60.0
1600 x 1200 75.0 60.0
1680 x 1050 65.3 60,0
640x480@67Hz 35.0 66.7
832x624@75Hz 49.7 74.6
1152x864@75Hz 68.7 75.1
Compatibility Resolution H-Sync [KHz] V-Sync [Hz]
480i 720 x 480 15.8 60
480p 720 x 480 31.5 60
576i 720 x 576 15.8 50
576p 720 x 576 31.3 50
720p 1280 x 720 37.5 50
720p 1280 x 720 45 60
1080i 1920 x 1080 33.8 60
1080i 1920 x 1080 28.1 50
1080p 1920 x 1080 67.5 60
1080p 1920 x 1080 56.3 50 
						

							39
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector for 
repairs. If the problem persists, contact your local reseller or service center. Please 
refer to "LED Indicator Messages" as well.
Start-up problems
If no lights turn on:
•
Be sure that the power cord is securely connected to the projector and the other end is 
plugged into an outlet with power.
• Press the power button again.
•
Unplug the power cord and wait for a short while, then plug it in and press the power
button again.
Image problems
If the searching source is displayed:
•
Press SOURCE on the projector or Source on the remote control to select an active 
input source.
• Be sure the external source is turned on and connected.
•
For a computer connection, ensure your notebook computer’s external video port is
turned on. Refer to the computer manual.
If the image is out of focus:
•
While displaying the on-screen menu, adjust the focus ring. (The image size should
not change; if it does, you are adjusting the zoom, not the focus.)
• Check the projection lens to see if it needs cleaning.
• If the image is flickering or unstable for a computer connection:
• Press 
MENU/EXIT on the projector or Menu on the remote control, go to Video/Audio 
and adjust Frequency or Tracking.
Remote control problems
If the remote control does not operate:
• Be sure nothing is blocking the remote control receiver on the front of the projector. 
Use the remote control within the effective range.
• Aim the remote control at the screen or at the front of the projector.
•
Move the remote control so it is more directly in front of the projector and not as far to 
the side. 
						

							40
RS-232 Command and Configuration
        !!!!!!!!!
D-Sub 9 pin
11 CD
2RXD
3TXD
4DTR
5GND
6DSR
7RTS
8CTS
9RI
Baud Rate 19200 bps
Data Length 8 bit
Parity Check None
Stop Bit 1 bit
Flow Control None Wire List
C1 COLOR C2
1 Black 1
2Brown 3
3Red 2
4 Orange 6
5 Yellow 5
6Green 4
7Blue 8
8Purple 7
9White 9
SHELL DW SHELL 
						

							41 Function Action Control Code
PowerPower on BE,EF,10,05,00,C6,FF,11,11,01,00,01,00 
Power off BE,EF,03,06,00,DC,DB,69,00,00,00,00,00
Source inputComputer1 BE,EF,03,19,00,19,29,01,47,02,CC,CC,00
Computer2 BE,EF,03,19,1E,90,72,01,47,02,CC,CC,00
S-Video BE,EF,03,19,00,E8,69,01,47,02,CC,CC,00
Video BE,EF,03,19,00,78,A8,01,47,02,CC,CC,00
HDMI BE,EF,03,19,00,DA,2B,01,47,02,CC,CC,00
Projector positionFront table BE,EF,10,07,9F,9D,0E,0A,EF,00,00,00,00
Rear table BE,EF,10,07,9F,9D,0E,0A,EF,01,00,00,01
Front ceiling BE,EF,10,07,9F,9D,0E,0A,EF,02,00,00,02
Rear ceiling BE,EF,10,07,9F,9D,0E,0A,EF,03,00,00,03
OSDMenu BE,EF,02,06,00,E9,D3,30,00,00,00,00,00
Up BE,EF,02,06,00,6D,D2,34,00,00,00,00,00
Down BE,EF,02,06,00,0B,D2,32,00,00,00,00,00
Left BE,EF,02,06,00,DA,D3,33,00,00,00,00,00
Right BE,EF,02,06,00,38,D2,31,00,00,00,00,00
LampECO on BE,EF,03,06,00,EF,DB,6A,00,00,00,00,00
ECO off BE,EF,03,06,00,3E,DA,6B,00,00,00,00,00
Using hours BE,EF,03,06,00,BA,DB,6F,00,00,00,00,00
FanHigh Attitude on BE,EF,02,06,00,40,D3,80,00,00,00,00,01
High Attitude off BE,EF,02,06,00,40,D3,80,00,00,00,00,00
KeystoneKeystone up BE,EF,03,06,00,10,DB,65,00,00,00,00,00
Keystone down BE,EF,03,06,00,23,DB,66,00,00,00,00,00
Aspect ratio4:3 BE,EF,03,06,00,0D,DA,68,00,01,00,00,01
16:9 BE,EF,03,06,00,0D,DA,68,00,02,00,00,02
Anamorphic BE,EF,03,06,00,0D,DA,68,00,02,00,00,04
Auto BE,EF,03,06,00,0D,DA,68,00,02,00,00,00
BlankBlank on BE,EF,02,06,00,DF,DF,66,00,01,00,00,01
Blank off BE,EF,02,06,00,DF,DF,66,00,02,00,00,02
FreezeFreeze on BE,EF,02,06,00,02,D0,2B,00,01,00,00,01
Freeze off BE,EF,02,06,00,02,D0,2B,00,02,00,00,02
Vo l u m eVolume + BE,EF,02,06,00,F1,DE,68,00,00,00,00,00
Volume - BE,EF,02,06,00,20,DF,69,00,00,00,00,00
Mute on BE,EF,02,06,00,0E,DE,67,00,01,00,00,01
Mute off BE,EF,02,06,00,0E,DE,67,00,02,00,00,02
Auto sourceAuto source on BE,EF,03,06,00,89,DB,6C,00,00,00,00,00
Auto source off BE,EF,03,06,00,58,DA,6D,00,00,00,00,00
Auto Sync BE,EF,02,06,00,86,D1,2F,00,00,00,00,00
Factory default BE,EF,03,06,00,6B,DA,6E,00,00,00,00,00
Firmware version BE,EF,03,06,00,D5,D9,70,00,00,00,00,00
System Status BE,EF,03,06,00,04,D8,71,00,00,00,00,00
3D Sync3D Sync on BE,EF,02,06,00,54,EF,7C,00,01,00,00,01
3D Sync off BE,EF,02,06,00,54,EF,7C,00,00,00,00,00
Top-Bottom BE,EF,02,06,00,54,EF,7C,00,01,00,00,02
Frame Sequential BE,EF,02,06,00,54,EF,7C,00,01,00,00,03
Frame Packing BE,EF,02,06,00,54,EF,7C,00,01,00,00,04
Side-By-Side BE,EF,02,06,00,54,EF,7C,00,01,00,00,05 
						

							42 Color modeBrightest BE,EF,03,06,00,38,5A,88,12,08,08,12,08
PC BE,EF,03,06,00,38,5A,88,10,00,00,10,00
Movie BE,EF,03,06,00,38,5A,88,13,01,01,13,01
ViewMatch BE,EF,03,06,00,38,5A,88,14,02,02,14,02
White Board BE,EF,03,06,00,38,5A,88,15,05,05,15,05
Black Board BE,EF,03,06,00,38,5A,88,16,06,06,16,06
Green Board BE,EF,03,06,00,38,5A,88,17,07,07,17,07
User 1 BE,EF,03,06,00,38,5A,88,18,03,03,18,03
User 2 BE,EF,03,06,00,38,5A,88,19,04,04,19,04
LanguageEnglish BE,EF,1A,0C,00,09,0B,3A,00,01,00,00,01
Nederlands BE,EF,1A,0C,00,09,0B,3A,00,02,00,00,02
BE,EF,1A,0C,00,09,0B,3A,00,03,00,00,03
BE,EF,1A,0C,00,09,0B,3A,00,04,00,00,04
Italiano BE,EF,1A,0C,00,09,0B,3A,00,05,00,00,05
BE,EF,1A,0C,00,09,0B,3A,00,06,00,00,06
BE,EF,1A,0C,00,09,0B,3A,00,07,00,00,07
BE,EF,1A,0C,00,09,0B,3A,00,08,00,00,08
BE,EF,1A,0C,00,09,0B,3A,00,09,00,00,09
BE,EF,1A,0C,00,09,0B,3A,00,0A,00,00,0A
BE,EF,1A,0C,00,09,0B,3A,00,0B,00,00,0B
BE,EF,1A,0C,00,09,0B,3A,00,0C,00,00,0C
Deutsch BE,EF,1A,0C,00,09,0B,3A,00,0D,00,00,0D
Svenska BE,EF,1A,0C,00,09,0B,3A,00,0E,00,00,0E
BE,EF,1A,0C,00,09,0B,3A,00,0F,00,00,0F
Suomi BE,EF,1A,0C,00,09,0B,3A,00,10,00,00,10
Polski BE,EF,1A,0C,00,09,0B,3A,00,11,00,00,11
Indonesia BE,EF,1A,0C,00,09,0B,3A,00,12,00,00,12
BE,EF,1A,0C,00,09,0B,3A,00,13,00,00,13
BE,EF,1A,0C,00,09,0B,3A,00,14,00,00,14
MagnifyMagnify Inc BE,EF,02,06,00,22,55,76,00,00,00,00,01
Magnify Dec BE,EF,02,06,00,22,55,76,00,00,00,00,00
Green ModeGreen Mode On BE,EF,02,06,00,40,B5,86,00,00,00,00,01
Green Mode Off BE,EF,02,06,00,40,B5,86,00,00,00,00,00
Dynamic ModeDynamic Mode On BE,EF,02,06,00,D3,D1,2A,00,00,00,00,01
Dynamic Mode Off BE,EF,03,06,00,EE,DA,6B,00,00,00,00,01
Quick Power OffQuickPowerOff_On BE,EF,10,05,00,C6,FF,11,11,01,00,01,01
QuickPowerOff_Off BE,EF,03,06,00,DC,DB,69,69,00,00,69,00