ViewSonic Pj650 Projector User Manual

							ViewSonic  PJ65028
Screen Menu
With the SCREEN menu, the five items shown in the Table below can be 
performed.
Please perform each operation in accordance with the instructions in the 
Ta b l e .
Item Description
BLANK Selection of BLANK Screen:
MyScreen  ORIGINAL , , , , 
, 
The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen 
has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the 
“Temporarily Blanking the Screen” section of the separate booklet, Vol. 1 (Basic)).
MyScreen:
 Using the MyScreen category (see this Table, below), one can register a desired screen 
(or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen.
ORIGINAL:
 Existing standard screens. Please make confirmation using the actual screen(s).
Option screens: 
Various colored non-patterned (plain) screens displayed within the Menus.
• The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color 
screen several minutes after being displayed.
START UP Selection of START UP Screen:
MyScreen   ORIGINAL   TURN OFF
The START UP Screen may be voluntarily selected. The START UP Screen is displayed when no 
signal has been inputted, or when spec signals are being inputted.
MyScreen:
 Using the MyScreen category (see this Table, below), one can register a desired screen 
(or screens). At the time of factory shipment, this is set as a non-pat- terned (plain) blue color 
screen.
ORIGINAL: 
Existing standard screens. Please make confirmation using the actual screen(s).
TURN OFF:
 A non-patterned (plain) blue color screen.
• The MyScreen and the ORIGINAL Screen will each change to the BLANK Screen several 
minutes after being displayed. 
						

							29ViewSonic  PJ650
MyScreen Registration of MyScreen:
When this item is executed, the MyScreen Menu for registration of MyScreen for the BLANK Screen 
and the START UP Screen is displayed. When operations are performed in accordance with this 
Menu, one can “cut” and register desired screens from among the received images within the 
display.
1. After the “Do you start capturing this picture?” message has been displayed, pressing the ESC 
(or RESET) button interrupts execution of the MyScreen. When the ENTER button is pressed, 
the picture becomes static (no longer moves), and a frame for picture cutting, as well as the 
message that follows below, appear. Please press the but- ton when the screen you want to 
register is currently being displayed.
2. When the “Move the capture area as you want.” message has been displayed, pressing the ESC 
(or RESET) button will eliminate the static state of the picture, and operations can be performed 
again from operation 1. The frame can be moved using the 
, , ,  buttons. 
After designating the screen you want to register, pressing the ENTER button will initiate screen 
registration. The registration process takes approximately 1 minute to complete.
3. When the registration has been completed, the screen of the registered MyScreen, and the 
message, “MyScreen registration is finished,” will be displayed for several seconds, after which 
the operation is terminated.
MyScreen Size Selection of MyScreen display size:
x1  FULL
MyScreen Lock Invalidation of MyScreen registration function:
TURN ON   TURN OFF
When TURN ON is selected, the MyScreen category (see this Table, above) cannot be executed. In 
this way, one can prohibit rewrites (“writeovers”) of the MyScreen 
						

							ViewSonic  PJ65030
Option Menu
With the OPTION menu, the five items shown in the Table below can be 
performed.
Please perform each operation in accordance with the instructions in the Table.
Item Description
VOLUME
Adjust Volume: 
High  Low
AUTO OFF Adjust AUTO OFF Time:
Long (MAX. 99 min.)   Short (Min. 1 min.)   (DISABLE: 0 min.) The 
system automatically enters the standby mode if no signal is received within the set time. This 
function is inactive when DISABLE (0 min.) is selected.
WHISPER Select WHISPER Mode:
NORMAL  WHISPER
When WHISPER is selected the WHISPER mode is activated. In the WHISPER mode, acoustic 
noise and screen brightness are reduced.
LAMP TIME Refer to LAMP TIME: 
When set, this function displays the total time the projector lamp has been 
used since new.
Reset LAMP TIME [Use this function only when the lamp has been replaced!]:
Depress the RESET button for at least 3 seconds while lamp time is being displayed. The reset 
menu will then appear. After you replace the lamp with a new lamp, select RESET
on the menu with the 
 button.
• Do not reset the lamp time unless you have replaced the lamp. And, always reset the lamp time 
when replacing the lamp. The message functions will not operate properly if the lamp time is 
not reset correctly.
• After the lamp running reaches 2000 hours, a warning message is displayed: “To maximize 
performance, lamp replacement is recommended.”, but won’t shut the unit off. The message 
display for 30 seconds when the PJ is turned on. If we push any button while displaying the 
message, the message disappears.
• Before replacing the lamp, carefully read the descriptions headed THE LAMP.
FILTER TIME Refer to FILTER TIME: 
This function displays the total time the air-filter has
been used since new.
Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]:
Depress the RESET button for at least 3 seconds while lamp time is being displayed. The reset 
menu will then appear. After you replace the filter, select RESET on the menu with
the 
 button.
DEFAULT  CANCEL
• Do not reset the filter time unless you have cleaned or replaced the filter. And, always reset the 
filter time when cleaning or replacing the filter. The message functions will not operate properly 
if the filter time is not reset correctly.
• Before cleaning or replacing the filter, carefully read the descriptions headed THE AIR 
FILTER. 
						

							31ViewSonic  PJ650
Maintenance
Lamp
To order a new lamp unit (Lamp Part # RLU-150-001), contact ViewSonic or your dealer. For the lamp part 
number, see the Optional Parts in the Specifications in this guide. For contact information, see the Customer 
Support table in this guide. Before replacing the lamp, turn the Power Switch OFF, remove the power cord 
from the power outlet, then wait at least 45 minutes until the lamp has cooled.
CAUTION:
 
The lamp may explode if handled at high temperatures.
    HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
 WARNING
The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a 
loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each 
lamp has a different lifetime, and some may burst or burn out soon after you start using them. In 
addition, when the bulb bursts, it is possible for shards of glass
 to fly into the lamp housing, and for 
gas containing mercury
 to escape from the projector’s vent holes
• If the lamp should break (it will make a loud bang when it does), unplug the power cord from 
the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards 
of glass could damage the projector’s internals, or cause injury during handling, so please do not 
try to clean the projector or replace the lamp yourself.
• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and 
make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or 
mouth.
• Do not open the lamp cover while the projector is suspended from above. This is dangerous, 
since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In 
addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced 
even if the bulb is not broken.
• If the indicators or a message prompts you to replace the lamp (see the section “Related 
Messages” and “Regarding the indicator Lamps”), replace the lamp as soon as possible. Using 
the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not 
use old (used) lamps; this is a cause of breakage.
• If the lamp breaks soon after the first time it is used, it is possible that there are electrical 
problems elsewhere besides the lamp. If this happens, contact your local dealer or a service 
representative.
• Use the lamp of the specified type only. (sold separately)
• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• Before replacing the lamp, make sure the power switch is off and the power cable is not plugged 
in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot 
can cause burns, as well as damaging the lamp.
• Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the 
screws are screwed in firmly. Loose screws could result in damage or injury.
• Obey local ordinances when disposing of used lamps. In most cases, it is possible to dispose of 
used bulbs in the same manner as used glass bottles, but in some cases, bulbs are sorted 
separately. 
						

							ViewSonic  PJ65032
Lamp Life
Projector lamps have a finite life. The projected images will become darker and hues will become weaker 
after a lamp has been used for a long period of time.
The LAMP indicator also becomes red when the lamp unit reaches a high temperature. Before replacing the 
lamp, switch the POWER OFF, wait approximately 20 minutes, then switch the POWER ON again. If the 
LAMP indicator still displays red, replace the lamp.
Replacing the Lamp
All projector lamps will wear out eventually. If used for long periods of time, the image could become 
darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. 
If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up the 
projector, the lamp needs to be replaced.
1
Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 45 minutes, and 
prepare a new lamp
2
After making sure that the projector has cooled adequately, slowly flip over the projector, so that the 
bottom is facing up
3
Unscrew the 2 screws, and remove the lamp cover
4
Unscrew the 1 screw, and slowly pull out the lamp by the handle
• Be careful not to touch the inside of the lamp case.
5
Insert the new lamp, and tighten the 1 screw firmly to lock it in place
• Also steadily push the opposite side of the screwed side of the lamp into the unit.
6
Replace the lamp cover, and tighten the 2 screws firmly to lock it in place
7
Slowly turn the projector so that the top is facing up
8
Turn on the projector power, and using the menu, reset the lamp timer
• To reset the lamp timer, from the OPTION menu, select LAMP TIME. 
						

							33ViewSonic  PJ650
ATTENTION:
• Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.
• Do not use with lamp cover removed.
• Do not reset the lamp timer without replacing the lamp. 
NOTE:
The LAMP indicator is also red when the lamp unit reaches high temperature.
Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If 
the LAMP indicator is still red, replace the lamp.
Caring for the Air Filter
The air filter should be cleaned about every 100 hours. Clean the filter if the LAMP indicator and TEMP 
indicator blink red simultaneously, or if a message prompts you to clean the air filter when you turn on the 
unit, the filter needs to be cleaned. (Refer to “On-Screen Messages” in the Trouble-shooting section.)
1
Turn off the projector, then unplug the power cord
2
To clean a reusable filter, carefully vacuum both sides of the filter area.
3
If the filter is damaged and needs to be replaced, contact your dealer or ViewSonic Corp. Replace the old 
filter then put the grill back in place.
4
To reset the Filter Timer, turn on the projector power, go to the Option menu then select filter timer. Reset 
the filter timer.
CAUTION:
• Switch power OFF and remove the power cord from the power outlet before beginning maintenance work.
• Replace the air filter if contamination cannot be removed or if it is damaged.
• Do not use the equipment with the air filter removed.
• When the air filter becomes clogged with dust etc., the power supply may switch OFF automatically to 
prevent the temperature from rising inside the projector.
• Make sure the lens is cool before cleaning.
• Do not use detergents or solvents such as benzene or thinners.
• Do not use chemical sprays.
• Use a soft cloth or lens paper only.
Air Filter Cover 
						

							ViewSonic  PJ65034
Caring for the Inside of the Projector
In order to ensure the safe use of your projector, please have it cleaned and inspected by an authorized Service 
Provider approximately once every 2 years. Never try to care for the inside of the unit yourself. Doing so is 
dangerous.
Caring for the Lens
Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens directly with 
your hand.
Caring for the Cabinet and Remote Control Transmitter
Wipe lightly with gauze or a soft cloth. If soiling is severe, dip a soft cloth in water or a neutral cleanser 
diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.
CAUTION:
• Make sure to turn off the power and unplug the power cord before caring for the unit. Please care-fully 
read all the PJ650 Quick START GUIDE in this manual, in order to care for your projector correctly.
• Do not use cleaners or chemicals other than those listed above, including benzene and paint thinner.
• Do not use aerosols or sprays.
• Do not polish or wipe with coarse material.
• Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth dampened with 
water, or water and a neutral detergent, and wipe dry with a soft, dry cloth. 
						

							35ViewSonic  PJ650
Troubleshooting
On-screen Messages
When the units power is ON, messages such as those shown below may be displayed. When any such 
message is displayed on the screen, please respond as described below.
Message Description
TO MAXIMIZE PERFORMANCE, 
LAMP REPLACEMENT IS RECOM-
MENDED.The unit does not display a warning message on the screen when 
the lamp expires or fails. When the lamp does not light, this indi-
cates that the lamp is no longer functional and should be replaced. 
Replace the lamp and do not forget to reset the timer.
CLEAN THE AIR FILTER
AFTER CLEANING AIR FILTER,
RESET THE FILTER TIMER.A note of precaution when cleaning the air filter.
After cleaning the filter, operate FILTER TIME of the OPTION Menu, 
then perform reset of the filter timer.
NO INPUT IS DETECTED
ON 
***There is no input signal.
Check the signal input connection and the status of the signal 
source.
SYNC IS OUT OF RANGE
ON 
***The horizontal or vertical frequencies of the inputted signal is out-
side of the operating range limits of this unit. Please confirm the 
specs for this unit or the signal source specs.
CHECK THE AIR FLOW
The internal temperature is rising. Please turn the power OFF, then 
allow the unit to cool down for approximately 20 minutes. After hav- 
ing confirmed the following items, then please reset the power to 
ON.
• Is there blockage of the air filter?
• Is the air filter dirty?
• Does the ambient temperature exceeds 35°C? 
						

							ViewSonic  PJ65036
Panel Lamp Indicators
Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the 
meanings as described in the Table below.
Please respond in accordance with the instructions within the Table.
NOTE:
When the interior portion has become overheated, for safety purposes, the power source is automatically 
turned OFF, and the indicator lamps may also be turned OFF. Press the “
O” (power OFF) side of the main 
power switch, and wait for approximately 20 minutes. Please then use the unit only after having first 
confirmed that the unit has sufficiently cooled down.
POWER
indicatorLAMP
indicatorTEMP
indicatorDescription
The orange 
lamp is lightedTurned OFF
(Not lighted)Turned OFF
(Not lighted)The STANDBY mode is set
Flashing of 
the green 
lampTurned OFF Turned OFF The unit is warming up. Please wait.
The green 
lamp is lightedTurned OFF Turned OFF The unit is in an ON state. Ordinary operations may be performed.
Flashing of 
the orange 
lampTurned OFF Turned OFF The unit is cooling down. Please wait.
Blinking of the 
red lamp- - The unit is cooling down. Please wait.
A certain error has been detected. Wait until the POWER indicator lamp 
has finished flashing, and then perform the proper response measure 
using the item descriptions below as reference.
The red lamp 
is lighted, or 
blinksThe red lamp 
is lightedTurned OFF The lamp does not light.
There is a possibility that the interior portion has become heated. Turn 
the power OFF and wait approximately 20 minutes. After the main unit 
has cooled down, please confirm whether or not there is blockage of the 
air passage aperture, whether or not the filter is dirty, and/or whether or 
not the peripheral temperature exceeds 35°C, etc. After performing any 
needed maintenance, turn the power ON again; if the same display is 
displayed, then please change the lamp.
The red lamp 
is lighted, or 
blinksBlinking of the 
red lampTurned OFF Either there is no lamp and/or lamp cover, or either of these has not 
been properly fixed (attached). Turn the power OFF and wait approxi-
mately 45 minutes. After the main unit has sufficiently cooled down, 
please make confirmation of the attachment state of the lamp and lamp 
cover. After performing any needed maintenance, turn the power ON 
again; if the same display is displayed, then please contact a sales store 
or a service company.
The red lamp 
is lighted, or 
blinksTurned OFF Blinking of the 
red lampThe cooling fan is not operating. Turn the power OFF and wait approxi-
mately 20 minutes. After the main unit has cooled down, please make 
confirmation that no foreign matter has become caught in the fan, etc. 
After performing any needed maintenance, turn the power ON again; if 
the same display is displayed, then please contact a sales store or a 
service company.
The red lamp 
is lighted, or 
blinksTurned  OFF The red lamp is 
lightedThere is a possibility that the interior portion has become heated. Turn 
the power OFF and wait approximately 20 minutes. After the main unit 
has cooled down, please confirm whether or not there is blockage of the 
air passage aperture, whether or not the filter is dirty, and/or whether or 
not the peripheral temperature exceeds 35°C, etc. After performing any 
needed maintenance, turn the power ON again; if the same display is 
displayed, then please contact a sales store or a service company.
The green 
lamp is lightedAlternative blinking with the red 
lampThere is a possibility that the interior portion has become overcooled. 
Please use the unit within the usage temperature parameters (0°C to 
35°C). After performing any needed maintenance, turn the power ON 
again; if the same display is displayed, then please contact a sales store 
or a service company.
The green 
lamp is lightedSimultaneous blinking with the 
red lampThis is a notification that it is time to clean the filter. After cleaning the fil-
ter, operate the FILTER TIME portion of the OPTION Menu, and perform 
reset of the FILTER TIME. 
						

							37ViewSonic  PJ650
Problem Diagnostics
Before requesting repair, please check the following chart. If the situation cannot be corrected, then contact 
your dealer.
NOTE:
When the interior becomes overheated, power to the unit automatically shuts down. Press the main switch on 
the side of the unit to the off position then wait 20 minutes to allow the unit to cool down before any work is 
done to the unit.
Phenomenon Cases not involving a 
machine defectItems to be confirmed
Power does not 
come ONThe main power source is not 
ON.Turn on the main power.
The electrical power cord is 
not plugged in.Correctly connect the power cord. points.
The main power source has 
been interrupted during opera-
tion, such as by a power out-
age (blackout), etc.Be sure to press the “O” (power OFF) side of the main power 
switch, and leave this OFF for approximately 20 minutes. After 
the unit has sufficiently cooled down, turn ON the power 
source.
No sound or pic-
tures are outputtedThe input changeover settings 
are mismatched.Select the input signal, and correct the settings.
The input changeover settings 
are mismatched.Correctly connect the connection cord.
No signal is being inputted. Correctly connect the connection cord.
Pictures are dis-
played, but no 
sounds are heardThe electrical wiring to this 
unit is not correctly connected.Correctly connect the connection cord.
The volume setting has been 
set at (or adjusted to) an 
extremely low level.Adjust the VOLUME setting to a higher level.
MUTE is turned on. Press the MUTE button to toggle the MUTE mode setting..
Sounds are heard, 
but no pictures are 
displayedThe electrical wiring to this 
unit is not correctly connected.Correctly connect the connection cord.
The brightness setting has 
been set at (or adjusted to) an 
extremely low level.Adjust the BRIGHT setting to a brighter level.
The lens cap has not been 
removed.Remove the lens cap.
Colors have a faded-
out appearance.
Color tone is poorColor depth setting or color 
tone settingPerform picture adjustments by changing the COLOR BAL R, 
the COLOR BAL B, and/or the TINT settings, etc.
Pictures appear darkThe brightness setting and/or 
contrast setting has not been 
properly adjusted.Perform picture adjustments by changing the BRIGHT and/or 
CONTRAST settings, etc.
The WHISPER mode is the 
current setting.Toggle from the WHISPER mode.
Lamp is approaching the end 
of its product lifetime.Repalce the Lamp Assembly.
Pictures appear 
blurryEither the FOCUS setting or 
the H PHASE is not properly 
adjusted.Adjust the FOCUS and H PHASE settings.