ViewSonic Pj588d Projector User Manual

4ViewSonic	 PJ588D/PJ568D/PJ508D

Rear view—connectors
ITEMLABELDESCRIPTIONSEE PAGE:
1.ViewPenMini USB Port for ViewPen receiver (optional)
2.RGB in (1)Connect a VGA cable (supplied) from a com-
puter
113.RGB in (2)Connect a VGA cable (supplied) from a com-
puter
4.RGB outConnect to a monitor
5.Power/Ready 
LEDLED light displays when unit is powered on
6.VideoConnect a composite video cable (not sup-
plied) from a video device
11
7.S-VideoConnect the supplied S-video cable from a 
video device...

5ViewSonic	 PJ588D/PJ568D/PJ508D

Bottom view
4
31
2
2
2
ITEMLABELDESCRIPTIONSEE PAGE:
1.Height adjuster buttonPush to release adjuster14
2.Ceiling mount holeContact your dealer for information on mounting the projector on a ceiling
3.Height adjusterAdjuster drops down when adjuster button is pushed
14
4.Tilt adjusterRotate adjuster lever to adjust angle position 

6ViewSonic	 PJ588D/PJ568D/PJ508D

Remote Control Parts
Important:Avoid using the projector when bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. Be sure nothing obstructs the path between the remote control and the p\
rojector. If the path between remote and projector is obstructed, you can bounce the remote signal off certain reflective surfaces such as projector screens.
ITEMLABELDESCRIPTIONSEE PAGE:
1.IR	 transm  tter Transm...

7ViewSonic	 PJ588D/PJ568D/PJ508D

5.R ght R  ght 	 arrow 	 when 	 connected 	 through 	 USB 	 to 	 a 	 PC
6.DownDown 	 arrow 	 when 	 connected 	 through 	 USB 	 to 	 a 	 PC
7.Page	 down Page 	 down 	 when 	 connected 	 through 	 USB 	 to 	 a 	 PC
8.Up	 cursor 	
Nav  gate 	 and 	 change 	 sett  ngs 	 n 	 the 	 OSD 	
179.R ght 	 cursor 	
10.Down	 cursor
11.Volume 	 +/- Adjust 	 volume18
12.MuteMute 	 the 	 bu  lt-  n 	 speaker
13.Zoom+Zoom 	 n 	
14.Zoom-Zoom...

8ViewSonic	 PJ588D/PJ568D/PJ508D

26.EnterEnter 	 key 	 when 	 connected 	 through 	 USB 	 to 	 a 	 PC
27.Power	 Turn 	 the 	 projector 	 on 	 or 	 off12
28.LaserUse 	 as 	 on-screen 	 po  nter. 	DO NOT POINT IN EYES
Remote Control Operating Range
The	remote	control	uses	nfrared	transm  ss  on	to	control	the	projector.	It	s	not	necessary	to	po  nt	the	
remote	d rectly	at	the	projector.	Prov  ded	you	are	not	hold ng	the	remote	perpend  cular	to	the	s...

9ViewSonic	 PJ588D/PJ568D/PJ508D

Some	buttons	on	the	projector	have	two	funct ons.	For	example,	tem	5/12	on	the	projector	funct  ons	
both	as	the	volume	down	button	and	as	the	left	cursor	key	n	OSD	menus. 

10ViewSonic	 PJ588D/PJ568D/PJ508D

SETUP AND OPERATION
Inserting the Remote Control Batteries
1.Remove	 the 	 battery 	 compartment 	 cover 	
by 	 sl  d  ng 	 the 	 cover 	  n 	 the 	 d  rect  on 	 of 	
the 	 arrow.
2.Insert 	 the 	 suppl  ed 	 batter  es 	 tak  ng 	 note 	
of 	 the 	 polar  ty 	 (+/-) 	 as 	 shown 	 here.
3.Replace	 the 	 cover.
Caution:
Only use AAA batteries.(Alkaline battery is better).
Dispose of used batteries according to local...

11ViewSonic	 PJ588D/PJ568D/PJ508D

Connecting Input Devices
A	PC	or	notebook	computer	as	well	as	video	devices	can	be	connected	to	the	projector	at	the	same	time.	
Video	devices	include	DVD,	VCD,	and	VHS	players,	as	well	as	movie	camcorders	and	digital	still	cameras. 	
Check	the	user	manual	of	the	connecting	device	to	confirm	it	has	the	appropriate	output	connector.	
ITEMLABELDESCRIPTION
ViewPenMini USB Port for ViewPen receiver (optional)
RGB in (1)Connect a VGA cable (not supplied) from a computer
RGB...

12ViewSonic	 PJ588D/PJ568D/PJ508D

Starting and Shutting Down the Projector
1.Connect the power cord to the pro-
jector (A). Connect the other end to 
a wall outlet. 
Turn on the power switch (B). 
The Power LED and Lamp-ready 
LED turn on.
2.Remove the lens cover.
3.Turn on the connected devices.
4.Ensure the Lamp-ready LED is on 
a steady (not flashing) orange and 
then press the Power button to turn 
on the projector.  
 
The projector splash screen displays 
and connected devices are detected. 
If...

13ViewSonic	 PJ588D/PJ568D/PJ508D

Setting an Access Password (Security Lock)
You	can	use	the	cursor	(arrow) 	buttons	to	set	a	password	and	prevent	unauthor  zed	use	of	the	
projector.	When	enabled,	the	password	must	be	entered	after	you	power	on	the	projector.	 (See	
“Nav  gat  ng	the	OSD”	on	page	18	and	“Sett  ng	the	OSD	Language”	on	page	19	for	help	on	us  ng	
OSD	menus.)
Important:
Keep the password in a safe place. Without the password, you will not be able to use the...