ViewSonic Pj560dc Projector User Manual

ViewSonic 15 PJ557DC/PJ559DC/PJ560DC
How to operate
1. Press the Menu button on the control panel or the MENU button on the remote
control to open the OSD menu.
2. When OSD is displayed, use S / T to select any feature in the main menu.
3.After selecting the desired main menu feature, press X to enter sub-menu for
feature setting.
4.Adjust the settings with W / X.
5. Press the Menu buttonon the control panel or the MENU button on the remote
control, the screen will return to the main menu.
6. To exit...

ViewSonic 16 PJ557DC/PJ559DC/PJ560DC
GammaEffect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.
Computer Image (Computer Mode)
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Video Image (Video...

ViewSonic 17 PJ557DC/PJ559DC/PJ560DC
Lamp Counter Reset
Reset the lamp counter to 0 hours.
Power Saving
If no operation is performed for a specific period of time, the power to the projector is
automatically turned off.
Auto Source
Automatically scan the input source.
ECO Mode
Use this function to dim the projector lamp light output which will lower power
consumption and increase lamp life.
High Altitude
Turning on High Altitude mode operates the fans at full speed continuously to allow for
proper high...

ViewSonic 18 PJ557DC/PJ559DC/PJ560DC
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning:
Never open any of the covers on the projector. Dangerous electrical voltages inside
the projector can cause severe injury....

ViewSonic 19 PJ557DC/PJ559DC/PJ560DC
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
„The lamp becomes high temperature after turning off the projector with the 
power button. If you touch the lamp, you may scald your...

ViewSonic 20 PJ557DC/PJ559DC/PJ560DC
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it from the mount.
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the 
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector. If the lamp does not turn on...

ViewSonic 21 PJ557DC/PJ559DC/PJ560DC
Specifications
Display Type Single 0.55 DLP panel
Resolution (Pixels) XGA (1024 × 768)
Lens Manual Zoom (1.1x)
Contrast Ratio 2000:1
Screen Size 27.8” – 255”
Lamp PJ557DC: 180W; PJ559DC: 200W; PJ560DC: 280W
Input / Output Source D-Sub 15 pin, S-video, composite video, USB, RS-232, Audio In, 
Audio Out
Speaker 10W (5W x 2)
Video Compatibility NTSC 3.58, NTSC4.43
PA L - 6 0 ,  M ,  N
SECAM, HDTV (480i/p, 576i/p, 720p, 1080i)
Scanning Frequency
Horizontal Freq.
Vertical...

ViewSonic 22 PJ557DC/PJ559DC/PJ560DC
Appendix
LED Indicator Messages
LED TypeColorStatusMeaning
LAMP LED
TEMP LEDGreen
OffFlash
-The projector is in standby mode.
LAMP LED
TEMP LEDGreen
GreenSolid
FlashThe projector system has some problems with
its fan, so the projector cannot start up.
LAMP LED
TEMP LEDGreen
GreenSolid
SolidThe lamp is in good condition and is projecting
at maximum brightness.
LAMP LED
TEMP LEDAmber
GreenSolid
SolidThe lamp has reached its end of life and must
be changed soon. The lamp...

ViewSonic 23 PJ557DC/PJ559DC/PJ560DC
Compatibility Modes
Computer: 
Video: 
 
CompatibilityResolutionH-Sync [KHz]V-S y nc  [Hz]
VGA 640 x 480 31.5 59.9
37.9 72.8
37.5 75.0
43.3 85.0
SVGA 800 x 600 35.2 56.3
37.9 60.3
48.1 72.2
46.9 75.0
53.7 85.1
XGA 1024 x 768 48.4 60.0
56.5 70.1
60.0 75.0
68.7 85.0
SXGA 1152 x 864 64.0 70.0
67.5 75.0
1280 x 960 60.0 60.0
75.0 75.0
1280 x 1024 64.0 60.0
WXGA 1280 x 768 47.8 60.0
60.3 74.9
68.6 84.8
1280 x 800 49.7 59.8
62.8 74.9
SignalHorizontal Frequency (kHz)Vertical...

ViewSonic 24 PJ557DC/PJ559DC/PJ560DC
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector
forrepairs. If the problem persists, contact your local reseller or service center. Please
refer to Indicator Messages as well.
Start-up problems
If no lights turn on:
„Be sure that the power cord is securely connected to the projector and the other endis plugged into an outlet with power.
„Press the power button again.
„Unplug the power cord and wait for a short while, then...