ViewSonic Pj559dc Projector User Manual

							ViewSonic 15 PJ557DC/PJ559DC/PJ560DC
How to operate
1. Press the Menu button on the control panel or the MENU button on the remote
control to open the OSD menu.
2. When OSD is displayed, use S / T to select any feature in the main menu.
3.After selecting the desired main menu feature, press X to enter sub-menu for
feature setting.
4.Adjust the settings with W / X.
5. Press the Menu buttonon the control panel or the MENU button on the remote
control, the screen will return to the main menu.
6. To exit OSD, 
press the Menu button on the control panel or the MENU button on
the remote control again. The OSD menu will close and the projector will
automatically save the new settings.
Picture (Computer / Video Mode)
Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, “Red”, “Green” and “Blue”
cab be adjusted.
Keystone
Correct the keystone distortion.
Aspect Ratio
Select how the picture fits on the screen:
„4:3 : The input source will be scaled to fit the projection screen.
„16:9 : The input source will be scaled to fit the width of the screen.
Image
There are many factory presets optimized for various types of images.
„PC : For computer or notebook.
„Movie : For home theater.
„Fine Color : For optimized color setting in daily application.
„sRGB : For PC standard color.
„User : Memorize user’s settings.
Screen Type
Select the projection screen type.
White Intensity
Increase the brightness of white areas. 
						

							ViewSonic 16 PJ557DC/PJ559DC/PJ560DC
GammaEffect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.
Computer Image (Computer Mode)
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Video Image (Video Mode)
Color
Adjust the intensity of colors.
Sharpness
Sharpen or soften the image.
Tint
Shift colors toward red or green.
Sound (Computer / Video Mode)
Vo l u m e
Adjust the volume level.
Mute
Cut off the sound temporarily.
Setting (Computer / Video Mode)
Menu Position
Choose the menu location on the display screen.
Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
Signal Type
Specify the source to the Computer In terminal that you wish to project.
„YPbPr : For component 480p,576p,720p,1080i signals
„RGB : For VGA signal
„YCbCr : For component 480i,576i signals
Lamp Counter
Display the lamp’s elapsed operating time (in hours). 
						

							ViewSonic 17 PJ557DC/PJ559DC/PJ560DC
Lamp Counter Reset
Reset the lamp counter to 0 hours.
Power Saving
If no operation is performed for a specific period of time, the power to the projector is
automatically turned off.
Auto Source
Automatically scan the input source.
ECO Mode
Use this function to dim the projector lamp light output which will lower power
consumption and increase lamp life.
High Altitude
Turning on High Altitude mode operates the fans at full speed continuously to allow for
proper high altitude cooling of the projector.
OSD Timeout
Duration OSD menu stays active (at idle state by second).
Option (Computer / Video Mode)
Blank Screen
Blank the screen temporarily, and select the screen color when this function is active.
Start-up Screen
Select start-up screen when the projector is powered on or when no signal is input.
User is the screen that you captured.
Screen Capture
Capture the current projection screen as a start-up screen.
Password
Set or change the password. When the password function is added, image projection
requires an entry of the preset password at power-on.
Language (Computer / Video Mode)Select the language used by the on-screen menu.
Factory Default (Computer / Video Mode)Restore all menu settings to factory default settings. 
						

							ViewSonic 18 PJ557DC/PJ559DC/PJ560DC
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning:
Never open any of the covers on the projector. Dangerous electrical voltages inside
the projector can cause severe injury. Do not attempt to service this product yourself.
Refer all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Cleaning the Air Filter
The air filter, which is located at the bottom of the projector, should be cleaned after
every 100 hours of use. If it is not cleaned periodically, it can become clogged with
dust and prevent the projector from being ventilated properly. This can cause over
heating and damage the projector.
To clean the air filter:1. Switch the projector off and unplug the AC 
power cord from the wall socket.
2. Remove the air filter cover as the 
illustration shown.
3. Clean the air filter.
„To clean the filter, you are advised to 
use a small vacuum cleaner 
designed for computers and other 
office equipment.
„If the dirt is difficult to remove or if the 
filter is torn, replace it.
4. Replace the filter.
5. Attach the air filter cover.  
6. Plug the power back into the projector.
„Turn off the projector and remove the AC power cord from the power outlet 
before beginning maintenance work.
„Make sure the lens is cool before cleaning.„Do not use detergents or chemicals other than those noted above. Do not use 
benzene or thinners.
„Do not use chemical sprays.„Use a soft cloth or lens paper only. 
						

							ViewSonic 19 PJ557DC/PJ559DC/PJ560DC
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
„The lamp becomes high temperature after turning off the projector with the 
power button. If you touch the lamp, you may scald your finger. When you 
replace the lamp, wait for at least 45 minutes for the lamp to cool down.
„Do not touch the lamp glass at any time. The lamp may explode due to 
improper handling, including the touching of the lamp glass.
„Lamp lifetime may differ from lamp to lamp and according to the environment 
of use. There is no guarantee of the same lifetime for each lamp. Some lamps 
may fail or terminate their lifetime in a shorter period of time than other similar 
lamps.
„A lamp may explode as a result of vibration, shock or degradation as a result of 
hours of use as its lifetime draws to an end. Risk of explosion may differ 
according to the environment or conditions in which the projector and lamp are 
being used.
„Wear protective gloves and eyeglasses when fixing or detaching the lamp.„Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least 
for 5 minutes to turn off the projector after powering on.
„Do not operate the lamp in proximity to paper, cloth, or other combustible 
material nor cover it with such materials. Otherwise it could cause a fire.
„Do not operate the lamp in an atmosphere containing an inflammable 
substance, such as thinner. Otherwise it could cause a fire or explosion.
„Thoroughly ventilate the area or the room when operating the lamp in an 
oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches, 
nausea, dizziness, etc.
„The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury 
inside the lamp will go out of the projector. Leave the area immediately if the 
lamp shatters while being operated and ventilate the area for at least 30 
minutes in order to avoid the inhalation of mercury fumes. Otherwise it could be 
harmful to user’s health. 
						

							ViewSonic 20 PJ557DC/PJ559DC/PJ560DC
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it from the mount.
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the 
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try 
reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Setting” menu.
„Dispose of the used lamp according to local regulations.„Ensure that screws are tightened properly. Screws not tightened fully may 
result in injury or accidents.
„Since the lamp is made of glass, do not drop the unit and do not scratch the 
glass.
„Do not reuse the old lamp. This could cause the lamp to explode.„Be sure to turn off the projector and unplug the AC power cord before 
replacing the lamp.
„Do not use the projector with the lamp cover removed. 
						

							ViewSonic 21 PJ557DC/PJ559DC/PJ560DC
Specifications
Display Type Single 0.55 DLP panel
Resolution (Pixels) XGA (1024 × 768)
Lens Manual Zoom (1.1x)
Contrast Ratio 2000:1
Screen Size 27.8” – 255”
Lamp PJ557DC: 180W; PJ559DC: 200W; PJ560DC: 280W
Input / Output Source D-Sub 15 pin, S-video, composite video, USB, RS-232, Audio In, 
Audio Out
Speaker 10W (5W x 2)
Video Compatibility NTSC 3.58, NTSC4.43
PA L - 6 0 ,  M ,  N
SECAM, HDTV (480i/p, 576i/p, 720p, 1080i)
Scanning Frequency
Horizontal Freq.
Vertical Freq.31 - 79 KHz
50 - 85 Hz
Noise Level Normal: 36dB; ECO: 34dB
Environment Operating:
Temperature: 5°C to 35°C
Humidity: 30%-85%
Storage:
Temperature: -20°C to 60°C
Humidity: 30%-85%
Power Requirement AC 100 - 240 V, 50 - 60 Hz
Power Consumption 230 W
Dimension 277 x 223 x 110 mm
Weight 2.5 kg (5.5lb)
Note: Design and Specifications are subject to change without prior notice. 
						

							ViewSonic 22 PJ557DC/PJ559DC/PJ560DC
Appendix
LED Indicator Messages
LED TypeColorStatusMeaning
LAMP LED
TEMP LEDGreen
OffFlash
-The projector is in standby mode.
LAMP LED
TEMP LEDGreen
GreenSolid
FlashThe projector system has some problems with
its fan, so the projector cannot start up.
LAMP LED
TEMP LEDGreen
GreenSolid
SolidThe lamp is in good condition and is projecting
at maximum brightness.
LAMP LED
TEMP LEDAmber
GreenSolid
SolidThe lamp has reached its end of life and must
be changed soon. The lamp will continue to
operate until it fails. Change the lamp. If the
lamp is off, then the ballast will become
malfunction.
LAMP LED
TEMP LEDAmber
AmberSolid
SolidThe projector is shutting and the fan motor is
cooling the lamp for shutdown. Do not unplug
the power cord or turn the power off before the
Lamp LED changes to flashing. The fan motor
will turn off when the lamp has cooled.
LAMP LED
TEMP LEDGreen
RedSolid
FlashTemperature is too high. The lamp will turn off.
The fan motor is cooling the lamp.
LAMP LED
TEMP LEDAmber
OffSolid
-The lamp ignition failed. If temperature is too
high, the fans will cool the lamp.  
						

							ViewSonic 23 PJ557DC/PJ559DC/PJ560DC
Compatibility Modes
Computer: 
Video: 
 
CompatibilityResolutionH-Sync [KHz]V-S y nc  [Hz]
VGA 640 x 480 31.5 59.9
37.9 72.8
37.5 75.0
43.3 85.0
SVGA 800 x 600 35.2 56.3
37.9 60.3
48.1 72.2
46.9 75.0
53.7 85.1
XGA 1024 x 768 48.4 60.0
56.5 70.1
60.0 75.0
68.7 85.0
SXGA 1152 x 864 64.0 70.0
67.5 75.0
1280 x 960 60.0 60.0
75.0 75.0
1280 x 1024 64.0 60.0
WXGA 1280 x 768 47.8 60.0
60.3 74.9
68.6 84.8
1280 x 800 49.7 59.8
62.8 74.9
SignalHorizontal Frequency (kHz)Vertical Frequency (Hz)
480i 15.8 kHz 60 Hz
480p 31.5 kHz 60 Hz
576i 15.6 kHz 50 Hz
576p 31.3 kHz 50 Hz
720p 45.0 kHz 60 Hz
720p 37.5 kHz 50 Hz
1080i 33.8 kHz 60 Hz
1080i 28.1 kHz 50 Hz 
						

							ViewSonic 24 PJ557DC/PJ559DC/PJ560DC
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector
forrepairs. If the problem persists, contact your local reseller or service center. Please
refer to Indicator Messages as well.
Start-up problems
If no lights turn on:
„Be sure that the power cord is securely connected to the projector and the other endis plugged into an outlet with power.
„Press the power button again.
„Unplug the power cord and wait for a short while, then plug it in and press the powerbutton again.
Image problems
If the searching source is displayed:
„Press the Source button one or more times to select another active input source.
„Be sure the external source is turned on and connected.
„For a computer connection, ensure your notebook computer’s external video port isturned on. Refer to the computer manual.
If the image is out of focus:
„Be sure the lens cover is open.
„While displaying the on-screen menu, adjust the focus ring. (The image size shouldnot change; if it does, you are adjusting the zoom, not the focus.)
„Check the projection lens to see if it needs cleaning.
If the image is flickering or unstable for a computer connection:
„Press the Resync button on the control panel.
„Press the Menu button on the control panel or the MENU button on the remote
control, go to Computer Image and adjust Frequency or Tracking.
Remote control problemsIf the remote control does not operate:
„Be sure nothing is blocking the remote control receiver on the front or back of the
projector. Use the remote control within the effective range.
„Aim the remote control at the screen or at the front or back of the projector.
„Move the remote control so it is more directly in front of or behind the projector andnot as far to the side.