Vidikron Projector Vision Model 90 User Manual

							Vidikron Vision Model 90 Owner’s Operating Manual 1-1 
1.1 
About This Manual
This Owner’s Manual describes how to install, set up and operate the Vidikron Vision 90 DLP 
Projector. Throughout this manual, the Vidikron Vision 90 DLP Projector is referred to simply 
as the “Vision 90.” 
Target AudienceVidikron has prepared this manual to help home theater installers and end users get the 
most out of the Vision 90. 
Vidikron has made every effort to ensure that this manual is accurate as of the date it was 
printed. However, because of ongoing product improvements and customer feedback, it 
may require updating from time to time. You can always find the latest version of this and 
other Vidikron product manuals on-line, at www.vidikron.com. 
If You Have Comments About 
This Manual...
Vidikron welcomes your comments about this manual. Send them to [email protected].
Textual and Graphic 
Conventions
Text Conventions: The following conventions are used in this manual, in order to clarify the 
information and instructions provided:
 Remote and built-in keypad button identifiers are set in upper-case bold type; for 
example, “Press EXIT to return to the previous menu.”
 All keys with functional names are initial-capped, set in bold type and enclosed in angle 
brackets. These keys are the following: , , ,  and 
.
 indicates that you may press either the RETURN or ENTER key on your keyboard 
if it has both keys.
 Computer input (commands you type) and output (responses that appear on-screen) is 
shown in monospace (fixed-width) type; for example: “To change the aspect ratio to 
Letterbox, type LETTERBOX .” 
In addition to these conventions, underlining, boldface and/or italics are occasionally used to 
highlight important information, as in this example:
1Introduction
A carriage return must be used after each command or string.Note 
						

							Introduction
1-2 Vidikron Vision Model 90 Owner’s Operating Manual
Graphic Conventions: These symbols appear in numerous places throughout the manual, 
to emphasize points that you must keep in mind to avoid problems with your equipment or 
injury: 
1.2 
Using This Manual
Use the following table to locate the specific information you need in this manual. 
TIPS highlight time-saving short cuts and helpful guidelines for using 
certain features. 
NOTES emphasize text with unusual importance or special significance. 
They also provide supplemental information. 
CAUTIONS alert users that a given action or omitted action can degrade 
performance or cause a malfunction.
WARNINGS appear when a given action or omitted action can result in 
damage to the equipment, or possible non-fatal injury to the user. 
DANGER appears when a given action can cause severe injury or death. 
Tip
Note
Caution
WARNING
DANGER!
If you need...... Turn to page:
Information about obtaining serviceiv
General information about the Vision 90 DLP 
Projector1-3
Installation instructions3-1
First-time configuration instructions 4-1
Advanced configuration instructions4-10
Troubleshooting tips5-1
Vision 90 DLP Projector specifications7-1 
						

							Introduction
Vidikron Vision Model 90 Owner’s Operating Manual 1-3 
1.3 
Description, Features and 
Benefits
Vidikron, a world leader in the high performance home cinema market, proudly introduces 
their latest high-definition digital cinema projector for the home: the Vision 90 Digital Light 
Processing (DLP™) Projector. 
The Vision 90 is specifically engineered to excel in the more traditionally-darkened home 
theater room environment, with outstanding white field uniformity, accurate color palette, 
maximum brightness and enhanced contrast performance in demand by avid home cinema 
enthusiasts around the world.
The Vision 90 produces an amazing 2250 ANSI lumens of light output (CSMS™ light output of 
45.3 ft-Lamberts). The Vision 90’s 16:9 native aspect ratio Digital Micromirror Device™ 
(DMD™) array makes it ideal for widescreen viewing, while its three-chip, 1280 x 720 native 
resolution produces crisp, crystal clear high definition images with richly saturated colors, 
deep black levels and natural, highly refined detail. 
Unlike previous, single-chip implementations of DLP, no color wheel is used. This reduces 
mechanical complexity and compromises to color spectrum purity. The Vision 90 is 
enhanced further by significant horizontal and vertical lens shift capability for maximum 
installation flexibility.
Vidikron’s exclusive all-digital Imagix™ video processing is integrated into the projector 
chassis for the most advanced video scaling and image quality available. This advanced 
design provides pure digital connections from input to light engine for absolutely stellar 
pictures. In addition, Vidikron’s multiple aspect ratio control includes its unique IntelliWide™ 
mode for viewing standard video formats in widescreen without loss of image quality. 
Discrete IR and RS-232 control make custom installation seamless, while discrete source and 
aspect ratio selection accommodate any automation control system. 
The Vision Model 90 is available in both a soft white or a graphite gray chassis to blend 
seamlessly in your home theater environment.
Key Features and BenefitsThe Vision 90 offers these key features and benefits: 
 Native Resolution: 1280 x 720 (16:9 Native Aspect Ratio) 
 3-chip Digital Light Processing (DLP™) system 
 Two DVI Inputs with High-bandwidth Digital Content Protection (HDCP)
HDTV Ready 
 Multiple Lens Options for Throw Distance Flexibility  
						

							Introduction
1-4 Vidikron Vision Model 90 Owner’s Operating Manual
Parts List Your Vision 90 is shipped with the following items. If any items are missing or damaged, 
please contact your Vidikron dealer or Vidikron Customer Service at (888) 4VIDIKRON. 
 Vision 90 DLP Projector
Remote Control Unit and two (2), AAA-size batteries 
 AC Power Cord
 Warranty information and registration card
 Vidikron Vision Model 90 Owner’s Operating Manual (this document) 
Optional Accessories: 
 Ceiling mount kit
 LiveLink™ DVI Cabling System
➤ 
						

							Vidikron Vision Model 90 Owner’s Operating Manual 2-1 
2.1 
Vision 90 at a GlanceFigure 2-1 shows the key Vision 90 components. 
Figure 2-1. Vision 90 Front/Bottom/Side View
1.EXHAUST VENT
2.CABLE OPENING 
Pass cables through this opening.
3.LENS
4.INTAKE VENT
5.IR SENSOR
6.VIDIKRON LOGO
2Controls and Functions
65 34122 
						

							Controls and Functions
2-2 Vidikron Vision Model 90 Owner’s Operating Manual
2.2 
Vision 90 Rear Panel
Figure 2-2 shows the Vision 90 rear panel. 
Figure 2-2. Vision 90 Rear Panel
1.DVI 1 / DVI 2 (Digital) 
Two, HDCP-compliant digital video inputs for connecting a DVD player or HD tuner with 
a DVI or HDMI output.
2.COMPONENT VIDEO (RCA connectors) 
Standard Definition (480i/576i) Component (YPrPb) input. This is the input for 
component video from sources such as DVD players.
3.HD1 / HD2 (Analog BNC connectors) 
Five, BNC connectors for connecting either RGB or component high-definition television 
signals. The Vision 90 automatically detects the signal format: RGB(HV) or YPrPb, 480p, 
720p, 480i, 576i or 1080i.
4.COMPOSITE VIDEO INPUT 
Standard composite video input for connecting a VCR, laser disc player or other 
composite video source.
VISION MODEL 90
DIGITAL PROJECTOR
DVI 1
DVI 1
HD1
HD2
Y
G
G
Y
H VINPUTS
HV
HD1HD2
INPUTS
R
Pr
Pr
R
B
Pb
Pb
B
DVI 2
DVI 2
COMPONENT VIDEO Pb
Pr Y
COMPONENT VIDEO Y
PrPb
VIDEO
VIDEO
S-VIDEO 2S-VIDEO 2S-VIDEO 1S-VIDEO 1
RS-232
CONTROL
RS-232
CONTROL
IR
IR
1
23
1 2
3TRIGGERSTRIGGERS
ENTER MENU
ENTER MENU
AC IN 110-240V 60HZAC IN 110-240V 60HZ
ON / OFFOFF / ON
STANDBY / POWERPOWER / STANDBY 
123786 45
91011151412161713191820
(LAMP COVER)
For best results, do not run your DVD player in progressive mode.Tip 
						

							Controls and Functions
Vidikron Vision Model 90 Owner’s Operating Manual 2-3 
5.12-VOLT (800 mA) TRIGGER OUTPUTS  
Connection for up to three (3), 12-volt trigger-controlled devices such as retractable 
screens or screen masks. 
6.S-VIDEO 1 / S-VIDEO 2 
Two, standard S-Video inputs for connecting a DVD player, satellite receiver or Super 
VHS (S-VHS) VCR. 
7.IR 
Wired input from an external remote control. 
8.RS-232 CONTROL PORT 
A female, 9-pin D-sub connector for interfacing with a PC or home theater 
automation/control system. 
9.VACUUM FLUORESCENT DISPLAY 
Can be used instead of the On-Screen Display (OSD). Displays currently-selected menu 
or -- if no menu is selected -- the current source, signal format (NTSC or PAL), input 
resolution and aspect ratio. 
10.UP BUTTON 
Use to direct select aspect ratios or move the menu cursor up in the On-Screen Display. 
When no menus are present on-screen, the UP button toggles you through aspect ratios 
in the following order: 
 
Anamorphic - Standard (4:3) - Letterbox - IntelliWide - Cinema 
 
(For more information about aspect ratios, refer to Table 4-1.)
11.LEFT BUTTON 
Used to direct select inputs or move the menu cursor left in the On Screen Display. When 
no menu is present on-screen, the LEFT button toggles you through the different 
sources, in this order: 
 
DVI 2 - DVI 1 - HD/RGB2 - HD/RGB1 - Component SD - S-Video 2 - S-Video 1 - Composite
12.DOWN BUTTON 
Use to direct select aspect ratios or move the menu cursor down in the On-Screen 
Display. When no menu is present on-screen, this button toggles you through the 
different aspect ratios, in this order: 
 
Cinema - IntelliWide - Letterbox - Standard (4:3) - Anamorphic
13.ENTER BUTTON 
When an item is highlighted on the On-Screen Display, the ENTER button selects the 
item.
14.RIGHT BUTTON 
Used to direct select inputs or move the menu cursor right in the On Screen Display. 
When no menus are present on-screen, the RIGHT button toggles you through the 
different sources, in this order: 
 
Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB 2 - DVI 1 - DVI 2
15.MENU BUTTON  
Pressing the MENU button will bring up the main menu. Also, if you are in an adjustment 
mode or function, pressing MENU will bring the menu back one level.
16.IR SENSOR 
Receives the IR commands from the remote. 
						

							Controls and Functions
2-4 Vidikron Vision Model 90 Owner’s Operating Manual
17.POWER BUTTON 
Press once to turn on the Vision 90. Press it again to put it into Standby mode. For a 
discrete on or off command, you can use the direct access buttons on the remote 
control.
18.POWER INPUT (100 to 240 VAC) 
Connect the Vision 90 to power here. 
19.MAIN POWER SWITCH 
Disconnects or applies power to the Vision 90.
20.POWER/STANDBY LED 
2.3 
Vision 90 Remote Control
Figure 2-3 shows the Vision 90 remote control, and the paragraphs that follow describe its 
functionality.
Figure 2-3. Vision 90 Remote Control Functions
HD
1
HD
2S-VID
2 S-VID
1
DVI
1
DVI
2 VIDEOISF
DAY ISF
NTCUST
1CUST
2
MEMORY
ENT
ENTMENU
COMP
SOURCE SELECTION
ANA 4x3LET
BOX
I-WIDECINEMA
LIGHT
OFFON
CODE
SVC ASPECT
123
456
78
1
2
7
10
14
19
22 1611 43
5
6
8
12
17
18
20
21 139
15 
						

							Controls and Functions
Vidikron Vision Model 90 Owner’s Operating Manual 2-5 
1.IR OUTPUT INDICATOR 
Lights when a button is pressed to indicate that an IR signal is being transmitted.
2.LIGHT  
Press to illuminate the buttons. 
3.ON / OFF 
Press to turn the projector on or off.
4.CODE 
For Service use only.
5.Cursor Keys (, , , )  
Use these buttons to select items or settings, adjust settings or switch display patterns. 
 
When no menus are present on-screen, the UP and DOWN buttons toggle through the 
available aspect ratios, in this order: 
 
UP Button = Anamorphic - Standard (4:3) - Letterbox - IntelliWide - Cinema 
DOWN Button = Cinema - IntelliWide - Letterbox - Standard (4:3) - Anamorphic 
 
Likewise, the LEFT and RIGHT buttons toggle through the different source inputs, in this 
order: 
 
LEFT Button = DVI 2 - DVI 1 - HD/RGB2 - HD/RGB 1 - Component SD - S-Video 2 - S-Video 
1 - Composite
 
RIGHT Button = Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB 
2 - DVI 1 - DVI 2
6.ENTER 
Press to select a highlighted menu item or confirm a changed setting.
7.MENU 
Press this button to access the OSD controls, or to exit the current menu and return to 
the previous one. 
Memory Preset Buttons: 
8.ISF NT (Night) 
Press to recall settings for the current input from the “ISF Night” memory preset. 
9.ISF DAY 
Press to recall settings for the current input from the “ISF Day” memory preset. 
10.CUST 1 
Press to recall settings for the current input from the “Custom 1” memory preset. 
11.CUST 2 
Press to recall settings for the current input from the “Custom 2” memory preset.  
						

							Controls and Functions
2-6 Vidikron Vision Model 90 Owner’s Operating Manual
Input Selection Buttons: Use these buttons to select an input source directly or to enter 
numeric characters, as follows. 
12.VIDEO (1) 
Press to select Composite video input as the source. 
13.S-VID 1 (2)/ S-VID 2 (5) (S-Video) 
Press to select an S-Video input. 
14.COMP (Component) (3)  
Press to select Component SD (480i/576i) video input as the source. 
15.HD 1 (4) / HD 2 (7)  
Press to select a HD (RGBHV or YPbPr component) input. 
16.DVI 1 (6) / DVI 2 (8)  
Press to select a Digital Video input. 
Aspect Ratio Selection Buttons: Use these buttons to select an aspect ratio directly or to 
enter numeric characters, as follows.
17.ANA (Anamorphic) (9)  
For 16:9 DVDs. 
18.4X3 (Standard 4:3) (0)  
The input signal is scaled to fit 4:3 display mode in the center of the screen. 
19.LETBOX (Letterbox) 
Image in letterbox format is enlarged to fit 16:9 full screen display and the upper/ lower 
portions are “blanked off.” 
20.I-WIDE (IntelliWide) 
A 4:3 image is enlarged NON-linearly in horizontal direction to fit 16:9 full screen display.
21.CINEMA  
The image in the Letterbox mode is enlarged to a 16x9 image and the upper and lower portions 
are compressed.
22.SVC 
Reserved for future use.