Vidikron Projector Vision Model 70 User Manual
Have a look at the manual Vidikron Projector Vision Model 70 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 45 Vidikron manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Vidikron Vision 70 Series Owner’s Operating Manual 69 PREL IMINARY 7.1 Vision 70 Specifications Table 7-1 lists the Vision 70 specifications. 7Specifications Table 7-1. Vision 70 Specifications Projector Type:Digital Light Processing (DLP), Single-Chip DMD Native Resolution:1920 x 1080 (16:9) Aspect Ratios:4:3, Letterbox, 16:9 Anamorphic, IntelliWide, Cinema, Cinema Fill Video Standards:NTSC, PAL, SECAM DTV Compatibility:480p, 576p, 720p, 1080i, 1080p Scan Frequency:Horizontal: 15 - 80 kHz Vertical: 50 - 100 Hz Picture Size (16:9 Screen):Recommended Width: 72 in. (1.83 m) to 96 in. (2.44 m) Capable of screen widths between 48 in. (1.22 m) and 200 in. (5.08 m) Throw Distance (Factor x Screen Width):Refer to Table 3-3 Horizontal and Vertical Lens Shift: Horizontal: None Vertical (when projector is inverted): Up = 40% of screen height above lens center Down = 50% of screen height below lens center
Specifications 70 Vidikron Vision 70 Series Owner’s Operating Manual PREL IMINARY Brightness and Contrast: Cinema Standards Measurement System (CSMS) Specifications - Brightness*: 14.7 to 21.5 foot-Lamberts (fL) - Contrast Ratio*: 195:1 to 218:1 *Variable depending on Aperture Control setting These measurements are taken from the projector in a controlled, home theater environment. All measurements are made to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter, Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The projector is calibrated to a color temperature of 6,500K and has a minimum of 150 hours of usage. The foot-Lambert (fL) is the unit of measurement used in commercial movie theaters to express image brightness at the screen surface. The Society of Motion Picture and Television Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using an open gate (without film in the projector). More importantly, today SMPTE specifies 12 fL as the target image brightness in Digital Cinema theaters. The foot-Lambert measurement is dependent on screen size, screen gain and projector light output. Home Theater Calibration Specifications - Light Output: 449 to 585 ANSI Lumens - Contrast Ratio*: 195:1 to 218:1 These specifications are obtained by calibrating the projector as described above for CSMS measurements. Industry-Standard Specifications - Light Output: 1225 ANSI Lumens - Contrast Ratio: 1400:1 to 3000:1 These are typical projector brightness and contrast specifications found in most companies’ sales literature. Vidikron includes these measurements in its literature to allow for direct comparison with other manufacturers’ projectors. These measurements are typically taken at 9,000K to 13,000K to get expected performance data when the projector is used in professional, commercial and industrial displays. Lamp:250 Watts Estimated Lamp Life: 2000 hours Video Inputs: (1) Composite Video, (1) S-Video, (1) RGB/Component Video (BNC connectors), (1) RCA Component Video, (1) HDMI Control Options:- Discrete IR remote -Built-in keypad - Serial commands via RS-232 RS-232 Communication Parameters: 9600, 38400 or 115200 bps, no parity, 8 data bits, 1 stop bit, no flow control 12V Output:Max. 0.25 Amps, active when Cinema or Cinema Fill Aspect Ratio is selected (Vision 70/CineWide with AutoScope only) or when projector is turned on; Tip = +12V; Sleeve = Ground Power Requirements:100 to 240 VAC (auto-sensing), 50/60 Hz, 330 Watts Operating Environment:41°F to 95°F (5°C to 35°C), 20% to 80% humidity (non-condensing) Dimensions:See Figure 7-1 Weight (without lens):46.5 lbs. (21.09 kg) Table 7-1. Vision 70 Specifications (continued)
Specifications Vidikron Vision 70 Series Owner’s Operating Manual 71 PREL IMINARY Regulatory Approvals:Complies with FCC, CE C-Tick Limited Warranty: Projector: Two (2) years parts and labor from the date of delivery to the end user. Lamp: 1000 hours or six (6) months, whichever comes first. Specifications are subject to change without notice. Table 7-1. Vision 70 Specifications (continued)
Specifications 72 Vidikron Vision 70 Series Owner’s Operating Manual PREL IMINARY 7.2 Vision 70 Dimensions Figure 7-1 shows the Vision 70 dimensions. Figure 7-1. Vision 70 Dimensions 14.9 in. (379.68 mm) 4.1 in. (103.89 mm) 17.3 in. (440.00 mm) 13.0 in. (330.00 mm) 11.0 in. (280.25 mm) 22.0 in. (560.51 mm) 4.4 in. (110.80 mm) 8.0 in. (203.00 mm) 8.8 in. (222.50 mm) 18.9 in. (480.00 mm) 6.9 in. (175.00 mm)
Vidikron Vision 70 Series Owner’s Operating Manual A-1 PREL IMINARY This Appendix describes how to personalize the ISF splash screen on the Vidikron Vision 70 Series DLP Projectors. 1. Connect a PC to the Vision 70 RS-232 port and establish a serial connection; refer to RS-232 Connection and Port Configuration on page 65 if you need instructions. 2. Press MENU on the projector remote control. Use the up- or down-arrow keys to highlight ISF Calibration and press ENTER. Use the number buttons on the remote control to enter the ISF Calibration menu passcode, then press ENTER again. 3. Press MENU on the projector remote control. Then, select Splash Screen Timer from the ISF Calibration menu. 4. Use the left- or right-arrow buttons to set the Splash Screen Timer. This timer controls how long the startup (Vidikron/ISF logo) image stays on-screen after you turn on the projector. The range is from 5 to 60 seconds in 1-second increments. For this procedure, set it to 30 seconds and press EXIT. 5. In the HyperTerminal window, at the command prompt (>), type U1 followed by the customer name, four or five spaces and the ISF calibrator name: 6. Press . 7. Press MENU on the projector remote control. Then, select ISF Calibration from the Main menu. 8. Select ISF Enable from the ISF Calibration menu and set it to On. Appendix A. Personalizing the ISF Splash Screen on the Vision 70 Only ISF-trained and -certified technicians should attempt this procedure!Note
Personalizing the ISF Splash Screen on the Vision 70 A-2 Vidikron Vision 70 Series Owner’s Operating Manual PREL IMINARY 9. Power-cycle the projector to see the change: CALIBRATED FOR: John Doe By: Tinh Ho CUSTOM BUILT BY:
Vidikron 2900 Faber Street Union City, CA 94587 510-324-5900 Fax 510-324-5905 1-888-4-VIDIKRON www.vidikron.com SERIAL NUMBER RUMA-011225 rev. 12-15-06 v1.0