Vidikron Projector Vision Model 12 User Manual
Have a look at the manual Vidikron Projector Vision Model 12 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 45 Vidikron manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Controls and Functions Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 11 PREL IMINARY 9. Not used. 10.LIGHT Press this button to illuminate the buttons. 11.CUST Press to recall settings for the current input from the “Custom” memory preset. 12.ISF NIGHT Press to recall settings for the current input from the “ISF Night” memory preset. 13.Cursor Keys (, , , ) Use these buttons to select items or settings, adjust settings or switch display patterns. 14.EXIT Press this button to exit the current menu and return to the previous one. 15.NUMBER KEYS Use these buttons to enter menu passcodes.
Controls and Functions 12 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual PREL IMINARY Notes:
Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 13 PREL IMINARY 3.1 Remote Control To install batteries in the remote control: 1. Press down the tab on the cover and pull the cover in the direction of the arrow. 2. Insert the included batteries. Ensure that the polarities correctly match the and markings inside the battery compartment. 3. Insert the lower tab of the cover into the opening, and press down the cover until it clicks in place. Notes on Batteries When installing batteries, make sure that the battery polarities are correct. Do not mix an old battery with a new one or different types of batteries. If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage. 3Installation
Installation 14 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual PREL IMINARY Notes on Remote Control Operation The remote control can be used to control the projector within the ranges shown in Figure 3-1. Figure 3-1. Available Range of the Remote Control For best results, hold the remote control within 23 feet (7m) of the back or top sensor and aligned within 30°. Do not drop the remote control or expose it to moisture or high temperature. The remote control may malfunction under a fluorescent lamp. If that occurs, move the projector away from the fluorescent lamp. Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the projector. If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones. Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the projector, and repeat the operation. ➤ The signal from the remote control can be reflected by the screen. 30° 45°23(7 m) 45° 30° 23(7 m) Note
Installation Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 15 PREL IMINARY 3.2 Quick Setup Table 3-1 gives a quick overview of the Vision 10/12 installation process. The sections following this one provide detailed instructions. Installation should be performed by a qualified custom video installation specialist. Table 3-1. Installation Overview StepProcedureFor Details, refer to page... 1Choose a location for the projector16 2Connect signal sources to the projector22 3Connect external controller to RS-232 port (optional)27 4Apply power to the projector 29 5For rear-screen and/or ceiling-mount installations, select the proper picture orientation 30 6Lens adjustments: projected image size (zoom), position (shift) and focus18, 31 7 Projector calibration: adjust the following for each input, starting with Component SD; save settings when finished: Aspect ratio Brightness Contrast Color level Tint Input position 34 through 43 Note
Installation 16 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual PREL IMINARY 3.3 Installation Considerations Proper installation of your projector will ensure the quality of your display. Whether you are installing a projector temporarily or permanently, you should take the following into account to ensure your projector performs optimally. Installation Type Choose the installation type that best suits your needs: front or rear screen, floor mount or inverted mount. Table 3-2 compares these various installation methods. Ambient Light In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your images will be noticeably reduced if light directly strikes the screen, such as when a shaft of light from a window or floodlight falls on the image. Images may then appear washed out and less vibrant. Other Considerations Other considerations and tips that can help improve your installation: Keep the ambient temperature constant and below 35°C (95°F). Keep the projector away from heating and/or air conditioning vents. Changes in temperature may cause drifts in the projector circuitry, which may affect performance. Keep the projector away from devices that radiate electromagnetic energy such as motors and transformers. Common sources of these include slide projectors, speakers, power amplifiers and elevators. ➤ Table 3-2. Projector Installation Options AdvantagesConsiderations Front Screen, Floor Mount Installation Easy to set up Can be moved or changed quickly Easy to access Shares floor space with audience Front Screen, Inverted Mount (ceiling) Installation Does not take up audience space Projector is unobtrusive Projector cannot be accidentally moved Installation is more permanent Projector access is more difficult Rear Screen, Floor Mount Installation Projector is completely hidden Projector is easily accessed Usually good ambient light rejection Requires separate room Installation cost is usually higher Rear Screen, Inverted Mount (ceiling) Installation Projector is completely hidden Usually good ambient light rejection Requires separate room Installation cost is usually higher Rear Screen, Floor Mount with Mirror Projector is completely hidden Usually good ambient light rejection Requires less space behind screen than other rear screen installations Requires separate room Installation cost is usually higher ➤ ➤
Installation Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 17 PREL IMINARY Throw DistanceThrow distance is the distance measured from the front of the projector to the screen. This is an important calculation in any projector installation as it determines whether or not you have enough room to install your projector with a desired screen size and if your image will be the right size for your screen. You can quickly estimate the throw distance by taking the width of the screen and multiplying it by the lens throw ratio; see Figure 3-2. • The Vision 10 has a lens throw ratio of between 1.40 and 1.60. • The Vision 12 has a lens throw ratio of between 1.42 and 1.65. The result of this calculation tells you roughly how far back the projector should be positioned from the screen in order to project a focused image large enough to fill the screen. For example, with an 8-foot (96-inch) wide screen: The Vision 10 has a throw distance range of between 134.4 inches (3.41 meters) and 153.6 inches (3.90 meters). The Vision 12 has a throw distance range of between 136.3 inches (3.46 meters) and 158.4 inches (4.02 meters). Figure 3-2. Estimating Throw Distance Estimating Throw Distance (TD) Vision Model 10 Minimum TD = Screen Width x 1.40 Maximum TD = Screen Width x 1.60 Vision Model 12 Minimum TD = Screen Width x 1.42 Maximum TD = Screen Width x 1.65
Installation 18 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual PREL IMINARY Vertical and Horizontal Position Proper placement of the projector relative to the screen will yield a rectangular, perfectly-centered image that completely fills the screen. Ideally, the projector should be positioned perpendicular to the screen and in such a way that the lens center and screen center are aligned with each other, as shown in Figure 3-3. Figure 3-3. Projector Placement Vertical and Horizontal Lens Shift If it is not possible to align the projector and screen as shown in Figure 3-3, you can use the lens shift controls to center the image on the screen. Lens shift is generally expressed as a percentage of the screen height or width, as shown in Figure 3-4 and Figure 3-5. Figure 3-4. Vertical Lens Shift ➤ Height Projection DistanceCeiling Ceiling Installation Screen Height Floor Lens Center Projection Distance Floor Installation Lens Center x Lens Center x ScreenLens Center ➤ Base plate to lens center = approx. 4 (depending on the amount of lens shift) 50% Height Lens Shift (0.5 x H) 100% Height Lens Shift (1.0 x H) 150% Height Lens Shift (1.5 x H) Screen Center0% Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens is used in this example.
Installation Vidikron Vision Model 10/Model 12 Owner’s Operating Manual 19 PREL IMINARYFigure 3-5. Horizontal Lens Shift 0%Screen Center 100% Width Lens Shift (1.0 x W) 50% Width Lens Shift (0.5 x W) 150% Width Lens Shift (1.5 x W) Screen Width (W) Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens is used in this example.
Installation 20 Vidikron Vision Model 10/Model 12 Owner’s Operating Manual PREL IMINARY Table 3-3 gives the lens shift limits for the Vision 10 and Vision 12, as percentages and absolute measurements with a 96 x 54 inch (1.78:1) screen. Adjusting the Projection Angle If the screen is significantly higher or lower than the projector, you can also tilt the projector at a slight angle. In a ceiling installation, you do this by adjusting the ceiling mount. For a floor installation, turn the four adjustable feet on the bottom of the projector to adjust the projector height and/or projection angle. If you do this, you may need to shift the image or apply keystone correction using the on-screen display (OSD) controls, to compensate. For detailed instructions, refer to Using the On-Screen Menus on page 32. Table 3-3. Vertical and Horizontal Lens Shift Limits Vision 10Vision 12 Lens Shift Limits, as Percentages of Screen Height or Width (Notes 1 and 2) Vertical (Note 2)Up40%46% Down60%63% Horizontal (Note 2)Left8% Right8% Lens Shift Limits in Inches, with a 96-by-54 inch (1.78:1) Screen VerticalUp21.6024.84 Down32.4034.02 HorizontalLeft7.68 Right7.68 Notes: 1. With no vertical or horizontal lens shift, the lens center and screen center are aligned with each other. 2. Vertical shift limits are percentages of the screen height. Horizontal shift limits are percentages of the screen width. 3. Vertical lens shift figures apply to ceiling mount configurations. For floor installations (where the projector is upright), reverse the up/down vertical offset percentages. ➤