Vidikron Projector Vision Model 100t User Manual

							Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual 1 
1.1 
About This Manual
This Owner’s Manual describes how to install, set up and operate a Vidikron Vision Model 90t 
or Model 100t DLP Projector. 
Throughout this manual, the Vidikron Vision Model 90t and Model 100t DLP Projectors are 
referred to collectively as the “Vision 90t/100t.” The information in this manual applies to 
both projectors except where otherwise indicated. 
Target AudienceVidikron has prepared this manual to help home theater installers and end users get the 
most out of the Vision 90t/100t. 
Vidikron has made every effort to ensure that this manual is accurate as of the date it was 
printed. However, because of ongoing product improvements and customer feedback, it 
may require updating from time to time. You can always find the latest version of this and 
other Vidikron product manuals on-line, at www.vidikron.com. 
If You Have Comments About 
This Manual...
Vidikron welcomes your comments about this manual. Send them to [email protected].
Textual and Graphic 
Conventions
Text Conventions: The following conventions are used in this manual, in order to clarify the 
information and instructions provided:
 Remote and built-in keypad button identifiers are set in upper-case bold type; for 
example, “Press EXIT to return to the previous menu.”
 Computer input (commands you type) and output (responses that appear on-screen) is 
shown in monospace (fixed-width) type; for example: “To change the aspect ratio to 
Letterbox, type LETTERBOX .” 
 All keys with functional names are initial-capped, set in bold type and enclosed in angle 
brackets. These keys are the following: , , , 
 and .
 indicates that you may press either the RETURN or ENTER key on your keyboard 
if it has both keys.
In addition to these conventions, underlining, boldface and/or italics are occasionally used to 
highlight important information, as in this example:
1Introduction
A carriage return must be used after each command or string.Note 
						

							Introduction
2 Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual
Graphic Conventions: These symbols appear in numerous places throughout the manual, 
to emphasize points that you must keep in mind to avoid problems with your equipment or 
injury: 
1.2 
Using This Manual
Use the following table to locate the specific information you need in this manual. 
TIPS highlight time-saving short cuts and helpful guidelines for using 
certain features. 
NOTES emphasize text with unusual importance or special significance. 
They also provide supplemental information. 
CAUTIONS alert users that a given action or omitted action can degrade 
performance or cause a malfunction.
WARNINGS appear when a given action or omitted action can result in 
damage to the equipment, or possible non-fatal injury to the user. 
DANGER appears when a given action can cause severe injury or death. 
Tip
Note
Caution
WARNING
DANGER!
If you need...... Turn to page:
Information about obtaining serviceiv
General information about the Vision 90t/100t DLP 
Projector3
Installation instructions13
First-time configuration instructions 27
Advanced configuration instructions38
Troubleshooting tips48
Vision 90t/100t DLP Projector specifications55 
						

							Introduction
Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual 3 
1.3 
Description, Features and 
Benefits
Congratulations on your purchase of a Vidikron Vision Model 90t or Model 100t (“Vision 
90t/100t“) Digital Light Processing (DLP™) Projector, among the world’s first THX® Certified, 
high-definition home theater projectors.
The Vision 90t/100t has been specifically engineered to produce high performance video in 
the kinds of environments most people use to enjoy their entertainment. Most high-end 
video projectors are intended for use in dedicated home theater environments with 
controlled lighting. However, many people prefer to have their entertainment systems in the 
rooms they use for everyday living. 
Vidikron has responded by creating the Vision Model 90t and Model 100t. The Vision 
90t/100t produces very high quality, high-resolution pictures even in rooms with plenty of 
light. The result is a plasma-like picture on a very large screen, even in daylight, with drapes 
open and lights ablaze! 
Vidikron has accomplished this by incorporating the most advanced 3-chip, high definition 
DLP™ technology. Unlike previous, single-chip implementations of DLP, no color wheel is 
used. This reduces mechanical complexity and compromises to color spectrum purity. The 
Vision 90t/100t is enhanced further by significant horizontal and vertical lens shift capability 
for maximum installation flexibility.
This technology is integrated into a specially designed light engine developed by Vidikron 
engineers to provide the perfect blend of high-quality image reproduction and extremely 
high light output. As a result, the Vision 100 produces an amazing 3500 ANSI lumens of light 
output (CSMS™ light output of 78.5 ft-Lamberts). The Vision 90 produces an impressive 2250 
ANSI lumens of light output (CSMS™ light output of 45.3 ft-Lamberts).
The Vision 90t/100t’s 16:9 native aspect ratio Digital Micromirror Device™ (DMD™) array 
makes it ideal for widescreen viewing, while its 3-chip, 1280 x 720 native resolution produces 
crisp, crystal clear high definition images with richly saturated colors, deep black levels and 
natural, highly refined detail. 
Vidikron’s exclusive all-digital Imagix™ video processing is integrated into the projector 
chassis for the most advanced video scaling and image quality available. This advanced 
design provides pure digital connections from input to light engine for absolutely stellar 
pictures. In addition, Vidikron’s multiple aspect ratio control includes its unique IntelliWide™ 
mode for viewing standard video formats in widescreen without loss of image quality. 
For uncompromising widescreen reproduction of movies originally filmed in the “scope” 
(2.35:1) format, the Vision 90t/100t can be equipped with Vidikron’s patent-pending 
CineWide™ with AutoScope™ system, which maintains constant vertical height on the screen 
just as in a movie theater. When a viewer transitions from 1.78:1 (16:9) program material to 
2.35:1, the image simply gets wider while full height is maintained.
Discrete IR and RS-232 control make custom installation seamless, while discrete source and 
aspect ratio selection accommodate any automation control system. 
THX recommends the use of 720p source material for optimal performance 
with this product. 
CineWide with AutoScope requires the use of a 2.35:1 or similar aspect ratio 
superwide format screen.
Note
Note 
						

							Introduction
4 Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual
The Vision 90t/100t is available in both a soft white or a graphite gray chassis to blend 
seamlessly in your home theater environment.
Key Features and BenefitsThe Vision 90t/100t offers these key features and benefits:
 Native Resolution: 1280 x 720 (16:9 Native Aspect Ratio)
 3-chip Digital Light Processing (DLP™) system 
 Two DVI Inputs with High-bandwidth Digital Content Protection (HDCP)
HDTV Compatible
 Multiple Lens Options for Throw Distance Flexibility 
Parts ListYour Vision 90t/100t is shipped with the following items. If any items are missing or 
damaged, please contact your Vidikron dealer or Vidikron Customer Service at (888) 
4VIDIKRON. 
 Vision 90t/100t DLP Projector
Remote Control Unit and two (2), AAA-size batteries 
 AC Power Cord
 3.0-mm, Ball-Point Hex Driver
 Warranty information and registration card
 Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual (this document) 
Optional Accessories: 
 CineWide™ with AutoScope™ system (anamorphic lens and motorized mount)
 Ceiling mount kit
 LiveLink™ DVI Cabling System
➤
➤ 
						

							Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual 5 
2.1 
Vision 90t/100t at a GlanceFigure 2-1 shows the key Vision 90t/100t components. 
Figure 2-1. Vision 90t/100t Front/Bottom/Side View
1. EXHAUST VENT
2.CABLE OPENING 
Pass cables through this opening.
3. LENS
4. INTAKE VENT
5. IR SENSOR
6. VIDIKRON LOGO
2Controls and Functions
65 34122 
						

							Controls and Functions
6 Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual
2.2 
Vision 90t/100t Rear Panel
Figure 2-2 shows the Vision 90t/100t rear panel. 
Figure 2-2. Vision 90t/100t Rear Panel
1.DVI 1 / DVI 2 (Digital) 
Two, HDCP-compliant digital video inputs for connecting a DVD player or HD tuner with 
a DVI or HDMI output.
2.COMPONENT VIDEO (RCA connectors) 
Standard Definition (480i/576i) Component (YPrPb) input. This is the input for 
component video from sources such as DVD players.
3.HD1 / HD2 (Analog BNCs) 
Two inputs (five BNCs per input) for connecting either RGB or component 
high-definition television signals. The Vision 90t/100t automatically detects the signal 
format: RGB(HV) or YPrPb, 480p, 720p, 480i, 576i or 1080i.
4.COMPOSITE VIDEO INPUT 
Standard composite video input for connecting a VCR, laser disc player or other 
composite video source.
DVI 1
DVI 1
HD1
HD2
Y
G
G
Y
H VINPUTS
HV
HD1HD2
INPUTS
R
Pr
Pr
R
B
Pb
Pb
B
DVI 2
DVI 2
COMPONENT VIDEO Pb
Pr Y
COMPONENT VIDEO Y
PrPb
VIDEO
VIDEO
S-VIDEO 2S-VIDEO 2
S-VIDEO 1S-VIDEO 1
RS-232
CONTROL
RS-232
CONTROL
IR
IR
1
23
1 2
3TRIGGERSTRIGGERS
ENTER MENU
ENTER MENU
AC IN 110-240V 60HZAC IN 110-240V 60HZ
ON / OFFOFF / ON
STANDBY / POWERPOWER / STANDBY 
123786 45
91011151412161713191820
(LAMP COVER)
For best results, do not run your DVD player in progressive mode.Tip 
						

							Controls and Functions
Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual 7 
5.12-VOLT (750 mA) TRIGGER OUTPUTS  
Connection for up to three (3), 12-volt trigger-controlled devices. These can be 
retractable screens, screen masks or the Vidikron CineWide with AutoScope system. 
6.S-VIDEO 1 / S-VIDEO 2 
Two, standard S-Video inputs for connecting a DVD player, satellite receiver or Super 
VHS (S-VHS) VCR. 
7.IR 
Wired input from an external remote control or infrared receiver. It is a 3.5-mm, mini 
phono jack, wired as follows:
 
Ring = +5V 
Tip = IR Input 
Sleeve = Ground 
8.RS-232 CONTROL PORT 
A female, 9-pin D-sub connector for interfacing with a PC or home theater 
automation/control system. 
9.VACUUM FLUORESCENT DISPLAY 
Can be used instead of the On-Screen Display (OSD). Displays currently-selected menu 
or – if no menu is selected – the current source, signal format (NTSC or PAL), input 
resolution and aspect ratio. 
10.UP BUTTON 
Use to direct select aspect ratios or move the menu cursor up in the On-Screen Display. 
When no menus are present on-screen, the UP button toggles you through aspect ratios 
in the following order: 
 
Anamorphic - Standard (4:3) - Letterbox - IntelliWide - Cinema - IntelliWide 2.35 
 
(IntelliWide 2.35 is available only on CineWide-equipped projectors. For more 
information about aspect ratios, refer to 
Table 4-1.)
11.LEFT BUTTON 
Used to direct select inputs or move the menu cursor left in the On Screen Display. When 
no menu is present on-screen, the LEFT button toggles you through the different 
sources, in this order: 
 
DVI 2 - DVI 1 - HD/RGB2 - HD/RGB1 - Component SD - S-Video 2 - S-Video 1 - Composite
12.DOWN BUTTON 
Use to direct select aspect ratios or move the menu cursor down in the On-Screen 
Display. When no menu is present on-screen, this button toggles you through the 
different aspect ratios, in this order: 
 
IntelliWide 2.35 - Cinema - IntelliWide - Letterbox - Standard (4:3) - Anamorphic
13.ENTER BUTTON 
When an item is highlighted on the On-Screen Display, the ENTER button selects the 
item.
14.RIGHT BUTTON 
Used to direct select inputs or move the menu cursor right in the On Screen Display. 
When no menus are present on-screen, the RIGHT button toggles you through the 
different sources, in this order: 
 
Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB 2 - DVI 1 - DVI 2
When an external remote control or infrared receiver is connected to the 
wired IR input, the IR sensors on the projector are disabled. Note 
						

							Controls and Functions
8 Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual
15.MENU BUTTON  
Pressing the MENU button will bring up the main menu. Also, if you are in an adjustment 
mode or function, pressing MENU will bring the menu back one level.
16.IR SENSOR 
Receives the IR commands from the remote.
17.POWER BUTTON 
Press once to turn on the Vision 90t/100t. Press it again to put it into Standby mode. For 
a discrete on or off command, you can use the direct access buttons on the remote 
control.
18.POWER INPUT (100 to 240 VAC) 
Connect the Vision 90t/100t to power here. 
19.MAIN POWER SWITCH 
Disconnects or applies power to the Vision 90t/100t.
20.POWER/STANDBY LED  
						

							Controls and Functions
Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual 9 
2.3 
Vision 90t/100t Remote 
Control
Figure 2-3 shows the Vision 90t/100t remote control, and the paragraphs that follow describe 
its functionality.
Figure 2-3. Vision 90t/100t Remote Control Functions
1.IR OUTPUT INDICATOR 
Lights when a button is pressed to indicate that an IR signal is being transmitted.
2.LIGHT  
Press to illuminate the buttons. 
3.ON / OFF 
Press to turn the projector on or off.
4.CODE 
For Service use only.
HD
1
HD
2S-VID
2 S-VID
1
DVI
1
DVI
2 VIDEOISF
DAY ISF
NTCUST
1CUST
2
MEMORY
ENT
ENTMENU
COMP
SOURCE SELECTION
ANA 4x3LET
BOX
I-WIDECINEMA
LIGHT
OFFON
CODE
SVC ASPECT
123
456
78
1
2
7
10
14
19
22 1611 43
5
6
8
12
17
18
20
21 139
15 
						

							Controls and Functions
10 Vidikron Vision Model 90t and Model 100t Owner’s Operating Manual
5.Cursor Keys (, , , )  
Use these buttons to select items or settings, adjust settings or switch display patterns. 
 
When no menus are present on-screen, the UP and DOWN buttons toggle through the 
available aspect ratios, in this order: 
 
UP Button = Anamorphic - Standard (4:3) - Letterbox - IntelliWide - Cinema - IntelliWide 
2.35
 
DOWN Button = IntelliWide 2.35 - Cinema - IntelliWide - Letterbox - Standard (4:3) - 
Anamorphic
 
 
Likewise, the LEFT and RIGHT buttons toggle through the different source inputs, in this 
order: 
 
LEFT Button = DVI 2 - DVI 1 - HD/RGB2 - HD/RGB 1 - Component SD - S-Video 2 - S-Video 
1 - Composite
 
RIGHT Button = Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB 
2 - DVI 1 - DVI 2
6.ENTER 
Press to select a highlighted menu item or confirm a changed setting.
7.MENU 
Press this button to access the OSD controls, or to exit the current menu and return to 
the previous one. 
Memory Preset Buttons: 
8.ISF NT (Night) 
Press to recall settings for the current input from the “ISF Night” memory preset. 
9.ISF DAY 
Press to recall settings for the current input from the “ISF Day” memory preset. 
10.CUST 1 
Press to recall settings for the current input from the “Custom 1” memory preset. 
11.CUST 2 
Press to recall settings for the current input from the “Custom 2” memory preset. 
IntelliWide 2.35 is available only on CineWide-equipped projectors. For 
more information about aspect ratios, refer to 
Table 4-1. Note