Vidikron Projector Vision Model 100 User Manual

							Operation
Vidikron Vision Model 100 Owner’s Operating Manual 4-7 
PLUGE patterns vary but generally consist of some combination of black, white and gray 
areas against a black background. The example above includes two vertical bars and four 
shaded boxes.
Select Brightness from the Picture menu and press ENTER. Adjust the brightness so that:
 The darkest black bars disappear into the background. 
 The dark gray areas are barely visible.
 The lighter gray areas are clearly visible.
 The white areas are a comfortable level of true white.
 The image contains only black, gray and white (no color).
Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the 
one shown in 
Figure 4-3. 
Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast
Select Contrast and press ENTER. Adjust the contrast to a point just below which the white 
rectangle starts to increase in size.
Brightness and contrast controls are interactive. A change to one may 
require a subtle change to the other in order to achieve the optimum 
setting. Note 
						

							Operation
4-8 Vidikron Vision Model 100 Owner’s Operating Manual
Color Saturation: On your external test pattern source, select a color bar pattern like the one 
shown in 
Figure 4-4. 
Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint
Select Color and press ENTER. While looking at the color bar pattern through a blue filter, 
adjust the color saturation level until the outermost (gray and blue) color bars appear to be a 
single shade of blue: 
Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. 
When tint is decreased, the image appears redder; when it is increased the image appears 
greener. To set the tint, select Tint and press ENTER. While looking at the color bar pattern 
through a blue filter, adjust the tint level until the cyan and magenta color bars (on either 
side of the green bar) appear to be a single shade of blue. 
Like the brightness and contrast controls, the color and tint controls are 
interactive. A change to one may require a subtle change to the other in 
order to achieve the optimum setting. 
gray
yellow
cyan
green
magenta
red
blue
gray
yellow
cyan
green
magenta
red
blue
Note 
						

							Operation
Vidikron Vision Model 100 Owner’s Operating Manual 4-9 
Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust 
sharpness, select Sharpness from the Picture menu and press ENTER. On your external test 
pattern source, select a pattern like the one shown in 
Figure 4-5. Adjust as needed, looking 
for white edges around the transitions from black to gray and different sized lines in the 
“sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them. 
Figure 4-5. Typical Test Pattern for Adjusting Sharpness
Input PositionUse the controls in the Input Position Menu to fine-tune the aspect ratio and image position 
for the current source. 
Left/Right: Select Left/Right from the Input Position menu to shift the projected image 
horizontally. Use the right or up cursor button to shift the image to the right; use the left or 
down button to shift it to the left. 
Up/Down: Select Up/Down from the Input Position menu to shift the projected image 
vertically. Use the right or up cursor button to shift the image upward; use the left or down 
button to shift it downward.
Width: Select Width from the Input Position menu to change the projected image width. Use 
the right or up cursor button to increase the width; use the left or down button to decrease it.
Height: Select Height from the Input Position menu to change the projected image height. 
Use the right or up cursor button to increase the height; use the left or down button to 
decrease it.
Input Position
Left/Right
Up/Down
Width
Height
OverscanWhen you change an input position setting, save the change to a preset 
afterwards. Otherwise, the change will be lost when a different input is 
selected. (The input position settings are saved for each input and 
resolution separately.) For information about saving settings, refer to 
ISF 
Presets on page 4-10. 
Note 
						

							Operation
4-10 Vidikron Vision Model 100 Owner’s Operating Manual
Overscan: Image Overscan pushes the outside edge of the active picture area of the video 
signal out beyond the edge of the display area. 
Some television programs are produced based on the assumption that older television sets 
may not display the outer edges of the broadcast picture area. Over scan effectively trims 
away these inactive, outer edges and enlarges the remaining portion of the image to fill the 
display area.
Select from 1% to 10% of Overscan, as desired.
For HDTV, DVDs and other video sources, Overscan is generally not necessary or desirable.
ISF Presets For each input, the Vision 100 lets you save image quality settings as presets that you can 
recall at a later time. You can create up to four presets per input and resolution. Use the ISF 
Presets menu to recall saved image presets, or to save image settings in the “Custom 1” or 
“Custom 2” memory location. The currently-selected preset is indicated by a “
7” to its left; in 
the example shown here, ISF Night is selected. 
You should save changes to any of the following settings to a preset; otherwise they will be 
lost when a new input source or resolution is selected:
 Aspect ratio
 Picture quality settings (brightness, contrast, color saturation, tint and sharpness)
 Input position (image position, width, height and overscan percentage)
To reset all image presets to their factory defaults, select Factory Default and press ENTER. 
Information Select Information from the Main Menu to see information that uniquely identifies your 
projector: its serial number, the installed hardware and firmware versions and the firmware 
version build date. Should you ever need to contact Vidikron Technical Support, this 
information will help them answer your questions or resolve product performance issues. 
Calibration Use the Calibration menu to perform advanced picture quality adjustments. This menu 
should be used by ISF-certified technicians only. 
The changes you make here take effect immediately; you do not need to save them. To recall 
the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the ISF Presets menu (see 
above). 
ISF Presets
7ISF Night
…ISF Day
…Custom 1      Save
…Custom 2      Save
Factory Default
➤
Information
Serial Number
Hardware
Firmware
Date
➤
Calibration
ISF Night
    Display Color
    Input Image
    Input Color
ISF Day
    Display Color
    Input Image
    Input Color
Output Shift
Splash Configure
OSD Position
➤
You must enter a passcode to access the Calibration menu. Note 
						

							Operation
Vidikron Vision Model 100 Owner’s Operating Manual 4-11 
ISF Night - Display Color: Use the Display Color settings to change the characteristics of the 
output signal. These settings are global (independent of any particular input). 
•Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A 
good way to do this is to use a test pattern consisting mostly of solid white areas, such as 
an 80 IRE “window” pattern. If the white areas contain traces of red, green or blue, 
decrease the Gain for that color.
• Offset: Use the Offset controls in the White Balance sub-menu to correct color imbalances 
in the dark areas of the image. A good way to do this is to use a test pattern consisting 
mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain 
traces of red, green or blue, decrease the Offset for that color.
•Gamma: “Gamma” is a global setting that determines how gray shades are displayed 
between minimum input (black) and maximum input (white) for all signals. A good 
gamma setting helps to optimize blacks and whites while ensuring smooth transitions for 
the “in-between” values utilized in other grays. Unlike “Brightness” and “Contrast” 
controls, the overall tone of your images can be lightened or darkened without changing 
the extremes and all images will be more vibrant while still showing good detail in dark 
areas. 
In all but the most unusual situations, the appropriate “Color Temp” selection (see below) 
will produce accurate colors and a satisfying contrast level. However, it is sometimes 
necessary to adjust the red, blue and green gamma curves individually. To do this, select 
Gamma from the Display Color sub-menu and use the left- and right-arrow buttons to 
manipulate the on-screen slidebars. 
•Lamp Power: Select Lamp Power from the Display Color Menu to adjust the lamp output 
level. You can choose to run the lamp as bright as possible (“1”; this is the default setting) 
or you can choose the lower setting (“0”). Generally, lower lamp output can prolong the 
life of the lamp, but decreases brightness. 
• Color Temp: Select Color Temp from the Display Color menu to adjust the color 
temperature. The default setting is appropriate for most situations. Higher settings 
produce a “bluer” picture. 
ISF Night - Input Image: The Input Image controls are similar to those in the Picture menu, 
but are accessible only by entering the Calibration menu passcode. This makes it possible to 
restore the picture quality settings to what they were when the projector was installed, 
simply by recalling the “ISF Night” preset. 
ISF Night - Input Color: The Input Color controls are similar to those in the Display Color 
menu (see above), but can be set independently for each input. 
• Gain/Offset: Refer to ISF Night - Display Color, above. 
• Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a 
Composite, S-Video or Component video source. Chroma delay in an image causes color 
shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a 
“halo” effect. If necessary, adjust this setting to eliminate them. 
•Phase: Adjust the phase if the image (usually from an RGB source) shows shimmer or 
“noise.” Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming 
signal. The effect of this control is similar to that of a tracking control on a VCR. 
For best results, use a good test pattern such as a smooth gray consisting of a clear pattern 
of black and white pixels, or a similar “half on, half off” graphic image. (You may notice 
that you can stabilize the image at more than one point. Use either setting in this case.)  
						

							Operation
4-12 Vidikron Vision Model 100 Owner’s Operating Manual
ISF Day - Display Color: Refer to ISF Night - Display Color. 
ISF Day - Input Image: Refer to ISF Night - Input Image. 
ISF Day - Input Color: Refer to ISF Night - Input Color. 
Output Shift: The controls in the Output Shift menu are similar to those in the Input Position 
menu, except that they change the characteristics of the output signal (so the change is 
visible no matter which input is selected). 
Splash Configure: Use the Splash Configure menu to customize the appearance of the 
start-up message that appears on the vacuum fluorescent display upon power-up. You can 
have the Vision 100 display the owner’s name, your name, the phrase “ISF Calibrated” and/or 
any other string, up to 20 characters in length. 
Use the up or down cursor button to select a character. Use the right and left cursor buttons 
to change the cursor position. Press MENU when you have finished entering text. Then, 
check the “Splash Enable” box to have the Vision 100 display the information you enter here 
when it is turned on. 
OSD Position: Select OSD Position, press ENTER and use the arrow buttons to change the 
size and position of the OSD controls.
Service Use the Service menu to access advanced projector configuration settings. This menu 
should be used by ISF-certified technicians only.
Test Video: Select Test Video from the Service Menu to access the internal test patterns on 
the Vision 100. Four patterns are available, consisting of white/gray or colored bars. These are 
useful for calibrating other theater source components (DVD player, HD tuner etc.) that have 
their own picture controls. 
Press MENU to exit test pattern mode. 
Language: Select Language from the Service menu and press the up- or down-arrows to 
select the OSD Language (English, French, Spanish or German).
Service
Test Video
Language
Remote Control
Display Device
HD Format
Triggers
Miscellaneous
System Reset
➤
You must enter a passcode to access the Service menu. Note 
						

							Operation
Vidikron Vision Model 100 Owner’s Operating Manual 4-13 
Remote Control: The Remote Control menu shows you the primary and secondary infrared 
(IR) codes to which the Vision 100 will respond. By default, both are set to 17. You can change 
these codes if either:
 Another device in the theater (a DVD player, for example) is responding to commands 
from the Vision 100 remote control in ways that are unpredictable or undesirable. 
 You have multiple Vision 100 projectors and want to control them independently, as 
opposed to broadcasting commands from a single remote to all of them. In this scenario, 
you can use multiple remotes programmed to use different IR codes. Or, you can use a 
single remote and change the IR code as needed to address a specific projector.
When you change a remote code on the Vision 100, you must re-program your remote 
control to send that same code. To do this:
1. Using a straightened paper clip or similar object, press and hold the CODE button on the 
remote control for approximately three seconds, or until the red LED on the remote 
lights solid red.
2. Enter a new two-digit code between 00 and 31 inclusive. Use the ANA button for “9” and 
the 4x3 button for “0.” Include a leading zero for single-digit codes; for example, enter 9 
as “09.”
3. The LED turns off to confirm the code change. If you enter an invalid code, the LED 
flashes for three or four seconds. Try again, entering a valid code. 
Display Device: The options in the Display Device menu allow you to change the picture 
orientation, reset the lamp timer, perform lens adjustments and access additional test 
patterns. 
• Installation: select Installation from the Display Device menu to change the picture 
orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or 
Ceiling Rear). 
This menu page also displays the number of hours that the lamp has been in service, and 
lets you reset the counter (which is recommended after you replace the lamp; refer to 
Lamp Replacement on page 5-1). 
•Lens: Select Lens from the Display Device menu to access the motorized lens controls. 
Refer to 
Lens Adjustments on page 4-2. 
•Diagnostics: Select Diagnostics from the Service menu to access additional test patterns 
for calibration or measurement purposes:
 Select Red, Green or Blue to display only the selected color (simulating a filter of that 
color). 
 Select 75 or 100 to display color bars (75 IRE or 100 IRE). 
 Select Horz or Ver t to display a horizontal or vertical gray ramp. 
 Select Checks to display a 15-segment checkerboard pattern. 
 Select Align to display a white grid against a black background (useful for verifying 
proper image or screen alignment). 
HD Format: If for some reason the Vision 100 does not properly detect the incoming signal 
format (color space) on the HD1 or HD2 inputs, specify it here (RGB or YUV). Otherwise, leave 
it set to Auto. 
Use the rear-panel keypad to change a projector IR code. Then, change the 
code sent by the remote to match as described below. Tip 
						

							Operation
4-14 Vidikron Vision Model 100 Owner’s Operating Manual
Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You 
can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated 
by selecting that aspect ratio. 
If your projector is equipped with the Vidikron CineWide with AutoScope system, assign at 
least one trigger output (the same one to which the lens motor is connected) to the Cinema 
and IntelliWide 2.35 aspect ratios.
Miscellaneous: Select Miscellaneous from the Service menu to set the following options: 
•Menu Mode: This is the manner in which the OSD menus appear and disappear when you 
press MENU. Choose one of the following: 
0 = No transition; menus abruptly appear and disappear.  
1 = Menus fade in and out.  
2 = “Checkerboard” dissolve; menus appear and disappear in sections.  
3 = “Window shade” effect; menus are drawn on a diagonal from top left to bottom right, 
and retract in the opposite direction. 
• Timeout - Short/Long: These settings control how long the OSD menus stay on screen. 
Select a time-out period of from 2 to 60 seconds. 
• Side Bar Color: This controls the color of the inactive image area. The range is from -100 
(black) to 100 (white). 
 
 
The inactive image area is on either side of the active image area when using the Standard 
4:3 aspect ratio, and above and below the active image area when using the Letterbox 
aspect ratio. 
System Reset: To reset ALL projector settings (including image settings) back to their factory 
defaults, choose System Reset from the Service menu. Select Confirm to continue or Back to 
cancel. This action is not undoable. Use it with caution!  
						

							Vidikron Vision Model 100 Owner’s Operating Manual 5-1 
5.1 
Lamp Replacement
The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or 
sooner if a noticeable degradation in brightness occurs. Contact your Vidikron dealer to 
obtain a replacement lamp.
1. Turn off the projector and unplug the power cord. Allow the projector to cool down for 
approximately 45 minutes prior to removing the lamp assembly for replacement.
2. Loosen the four rear Lamp Cover screws and remove the cover.
3. Remove the two lamp assembly mounting screws.
4. Grasp the lamp assembly handle and pull gently, removing the lamp module from the 
projector housing.
5. Install the new lamp module. 
6. Replace the lamp cover and re-tighten all screws.
7. Reset the Lamp Hour counter. To do this, select Service from the Main Menu, then 
Display Device, then Installation. Use the cursor buttons to highlight Reset under 
“Lamp
 Hours” and press ENTER. 
5.2 
Troubleshooting Tips
Table 5-1 provides some general guidelines for troubleshooting problems you may 
encounter with the Vision 100. If you encounter an issue not described here, please contact 
Vidikron Technical Support. 
5Maintenance and Troubleshooting
Table 5-1. Troubleshooting Chart 
SymptomPossible Cause(s)Solution
The projector does not turn on 
after initial installation. The 
power LED lights red after you 
press the power button.  The Vision 100 is not 
plugged in or the AC outlet 
is not active.  Ensure that the Vision 100 is 
plugged in and that the AC 
outlet is active. 
The projector is on, but there is 
no video image on-screen.  Incorrect source selection. 
 Source component is not 
turned on. 
 Select the correct source. 
 Turn on the source. 
A projected image from a DVD 
is split or otherwise scrambled. DVD player is set to 
progressive scan mode.  Turn off progressive scan 
on the DVD player. 
 Connect the DVD player to 
the HD/RGB 1 or HD/RGB
 2 
input. 
Image is too bright and/or 
lacks definition in the bright 
areas of the image.  Contrast is set too high.  Lower the contrast setting. 
Image appears “washed out” 
and/or dark areas appear too 
bright.  Brightness is set too high.  Lower the brightness 
setting.  
						

							Maintenance and Troubleshooting
5-2 Vidikron Vision Model 100 Owner’s Operating Manual
Colors in the image are 
swapped; for example, reds 
appear blue or vice versa.  The Red/Pr, Green/Y or 
Blue/Pb outputs from the 
source are connected to the 
wrong inputs on the Vision 
100.  Ensure that the source 
outputs are connected to 
the correct Vision 100 
input. 
The projector will not turn 
back on after it was powered 
down, or the image disappears 
during operation.  The projector will not turn 
on for two minutes after 
power-down, to protect the 
lamp. 
 The lamp has failed. 
 Wait two minutes until the 
LED at the front of the 
Vision 100 turns red. 
Table 5-1. Troubleshooting Chart (continued)
Symptom Possible Cause(s) Solution