Home > Uniden > Communications receiver > Uniden Receiver Atlantis Operating Instructions

Uniden Receiver Atlantis Operating Instructions

    Download as PDF Print this page Share this page

    Have a look at the manual Uniden Receiver Atlantis Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 50 Uniden manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Attaching the Battery Pack
    1. Slide the battery pack onto the bottom
    of the radio
    2. Use a coin or screwdriver to turn the 
    screw that connects the battery pack
    to the ATLANTIS. Be sure the battery 
    pack fits tightly against the 
    ATLANTIS body.
    7
    Atlantis_OM.qxd  06/08/2001  4:51 PM  Page 11 
    						
    							8
    Attaching the spacer to the beltclip
    A spacer is included to be used with
    the optional Speaker/Microphone. The
    spacer must be affixed to the beltclip
    of your ATLANTIS radio.
    Remove the backing from the spacer
    and attach it to the upper part of the
    beltclip.
    Do not operate your ATLANTIS radio when
    using the optional Speaker/Microphone
    unless the spacer is properly affixed behind
    the beltclip.
    In order to reduce the likelihood of exces-
    sive radio frequency exposure, the spacer
    is provided for you to increase the distance
    between the radio antenna and the human
    body when operating the radio while
    attached to your belt. Additional steps
    should be taken to maintain a separation
    distance of at least 1 inch between the
    antenna and the human body.
    Atlantis_OM.qxd  06/08/2001  4:51 PM  Page 12 
    						
    							Charging the Battery Pack
    Your marine radio is powered by a 
    specially designed NiMH battery pack
    or an Alkaline battery pack. (Alkaline
    batteries are not included.) Before
    operating the ATLANTIS, charge the
    NiMH battery pack for 15 hours without
    interruption the first time.
    1. Place the ATLANTIS in the cradle 
    holder.
    +You can monitor incoming calls while 
    the ATLANTIS is in the cradle holder.
    +You can charge the battery pack 
    alone or connected to the 
    ATLANTIS.
    +Periodically, the NiMH battery 
    should be fully drained prior to 
    recharging.
    9
    Atlantis_OM.qxd  06/08/2001  4:51 PM  Page 13 
    						
    							Operation
    +When you press any key (except 
    PTT), a short tone sounds.
    +When you turn on your ATLANTIS, it 
    is automatically tuned to channel 16, 
    the United States Coast Guard 
    frequency for distress, safety, and 
    calling.
    +See the foldout in the front of the 
    operating guide for button, knob, and 
    key positions.
    Turning on the Unit and Setting Squelch
    1. Before you turn on the
    unit, turn the 
    Squelch
    knob fully counter
    clockwise.
    2. Then, turn on the Unit 
    by turning the 
    Volume/Powerknob 
    clockwise until you 
    hear a hissing sound.
    3. Turn the 
    Squelchknob 
    clockwise, just until the 
    hissing sound stops.
    Use the knob to adjust 
    to the desired squelch 
    level. Think of the 
    squelch control as a 
    frequency gate which 
    controls access to 
    weak or strong signals depending on 
    its setting.
    +To listen to a weak or distant station, 
    turn the knob counterclockwise.
    +If the tracking squelch control is 
    adjusted so you continually hear a 
    hissing sound, the unit will not scan 
    properly.
    4. To turn off the unit, turn the 
    Volume/Powerknob counterclockwise.
    10
    Atlantis_OM.qxd  06/08/2001  4:51 PM  Page 14 
    						
    							Selecting a Channel
    1. Turn on your ATLANTIS.
    2. To select a higher 
    channel, press the s
    arrow key.
    3. To select a lower 
    channel, press the t
    arrow key.
    +To change the channel continuously, 
    press and hold the sor tkey.
    One-touch Channel 16/9
    Example:While you are monitoring 
    channel 20, you want to 
    check channel 16 or 9.
    1. You are now on 
    channel 20.
    2. To monitor channel 16, 
    press the 
    16/9/TRI
    button.
    3. To monitor channel 9, 
    press the 
    16/9/TRI
    button again.
    4. To return to channel 20, press the 
    16/9/tributton again.
    11
    Atlantis_OM.qxd  06/08/2001  4:51 PM  Page 15 
    						
    							Triple Watch
    Triple Watch mode monitors channels
    16 and 9 for a signal while you listen
    to the currently selected channel. The
    marine radio checks channel 16 and 9
    for activity every 2 seconds.
    1. To select Triple Watch 
    mode, press and hold 
    the 
    16/9/TRIbutton for 
    2 seconds. A confirma--
    tion tone sounds.
    2. To exit from Triple 
    Watch, press and hold 
    16/9/TRIfor 2 seconds.
    A confirmation tone 
    sounds.
    +While in Triple Watch mode, you can 
    change the currently selected 
    channel using the sor tarrow key.
    +A momentary press of the 
    16/9/TRI
    button interrupts Triple Watch mode 
    and remains on 16. Press 
    16/9/TRI
    again to monitor channel 9. A third 
    press will return to the main channel 
    and resume the Triple Watch mode.
    At anytime you may press and hold 
    the 
    16/9/Tributton for 2 seconds to 
    return to the previous Triple 
    Watch mode.
    12
    Atlantis_OM.qxd  06/08/2001  4:51 PM  Page 16 
    						
    							Monitoring Weather  Channels
    The ATLANTIS has 10 preprogrammed
    weather channel frequencies, 
    represented by 1 through 10.
    1. To listen to the weather 
    channels in your area, 
    press 
    WX/ALERT.WX
    appears on the display.
    2. To move up, press the s
    arrow key.
    3. To move down, press 
    the tarrow key.
    4. To exit, press 
    WX/ALERT.WX
    disappears from the 
    display.
    +To change the channel continuously, 
    press and hold the sor tarrow 
    button for more than 1 second.
    13
    Atlantis_OM.qxd  06/08/2001  4:51 PM  Page 17 
    						
    							Weather Alert
    Weather Alert allows your ATLANTIS to
    function as a severe weather radio. If
    NOAA issues a severe weather warn-
    ing while the Weather Alert is turned
    on, the ATLANTIS sounds an alert
    tone. You will then hear the 
    emergency weather broadcast.
    1. To use Weather Alert, 
    select the weather 
    Channel in your area
    2. Press and hold 
    WX/ALERTfor 2 seconds.
    A confirmation tone sounds.
    3. When the unit receives 
    a warning signal, it 
    beeps for 5 seconds.
    WX, ALERT,and the 
    channel number blink to receive the 
    emergency weather broadcast.
    4. To turn off Weather Alert, press and 
    hold 
    WX/ALERTfor 2 seconds. A 
    confirmation tone sounds.
    +When Weather Alert is activated, the 
    highest priority is given to this func-
    tion. If the unit is in scan, Triple 
    Watch, or any other marine 
    channels, it checks for the weather 
    alert signals every 7 seconds and 
    switches to the Weather Channel 
    automatically.
    *NOTE: Be sure the volume is set to a 
    high level when using the 
    Weather Alert mode. This will 
    insure that you will hear the 
    Alert tone even in a noisy 
    environment.
    14
    Atlantis_OM.qxd  06/08/2001  4:51 PM  Page 18 
    						
    							USA, International and Canada Channels
    1. The ATLANTIS is 
    initially set for USA 
    marine channels When 
    you turn on your radio.
    2. To receive and transmit 
    on international marine 
    channels, press 
    U/I/C.
    3. To receive and transmit 
    on Canadian marine 
    channels, press 
    U/I/C
    again.
    4. The radio will keep the last mode 
    setting that was selected when turned 
    back on.
    +For USA, international and Canadian
    marine channels and functions, refer 
    to the tables starting on page 20.
    Programming Channel into Memory
    Before using the scanning feature, you
    have to program channels into memory.
    1. Select the channel to enter into 
    memory by pressing the sor t
    arrow key.
    2. Press the 
    MEMbutton 
    to store the channel.
    MEMappears on the 
    display.
    Deleting a channel from memory
    1. Select the channel to delete from 
    memory by pressing the sor t
    arrow key.
    2. Press the 
    MEMbutton.MEMdis-
    appears from the display.
    15
    Atlantis_OM.qxd  06/08/2001  4:51 PM  Page 19 
    						
    							Scanning
    1. To begin scanning the 
    programmed channels, 
    press the 
    SCANbutton.
    MEM, SCANand TRIPLEappear on 
    the display.
    2. To stop scanning, press the 
    SCAN
    button once more.SCANand TRIPLE
    disappear from the display.
    +Scanning starts from the lowest to 
    highest channel and stops when it 
    finds an active channel. It remains 
    on that channel until the transmis-
    sion ends, then resumes scanning 
    after a 3 second delay period.
    +When in the scan mode, the unit 
    automatically activates the Triple 
    Watch feature. To deactivate Triple 
    Watch from the scanning mode, 
    press and hold the 
    16/9/TRIbutton 
    for 2 seconds.TRIPLEdisappears 
    from the display.
    16
    Atlantis_OM.qxd  06/08/2001  4:51 PM  Page 20 
    						
    All Uniden manuals Comments (0)

    Related Manuals for Uniden Receiver Atlantis Operating Instructions