Uniden Pro-2035 Vhf Uhf Scanner Owners Manual

PRO-2035 1000-Channel Programmable Home Scanner 
(200-0460)       Listening to the Weather Band         Faxback Doc. # 16914 
 
The FCC (Federal Communications Commission) has allocated 11 channels for 
use by the National Oceanic and Atmospheric Administration (NOAA).  NOAA 
broadcasts your local forecast and regional weather information on one or 
more of these channels.  We have preprogrammed the scanner with ten of the 
U.S. frequencies available to NOAA. 
 
To scan the preprogrammed weather...

Changing/Resetting the Frequency Step 
 
The scanner scans at a preset frequency step (5, 12.5, or 50 kHz) for each 
frequency range.  However, if you scan some of the 225-400 MHz and TV audio 
bands, you might have to manually change the frequency step. 
 
You can change the displayed frequency step while searching for frequencies 
or automatically storing frequencies. 
 
Follow these steps to change the displayed frequency step. 
 
1.  Display the frequency step or frequency range which uses the...

PRO-2035 1000-Channel Programmable Home Scanner 
(200-0460)                 Operation -Part 1           Faxback Doc. # 16910 
 
CONNECTING POWER 
 
Plug the scanners attached AC power cord into a standard AC outlet. 
 
CAUTION: To prevent electric shock, the plugs blades are polarized and fit 
         only one way.  If the plug does not fit easily, turn it over and 
         try again.  Do not force the plug into the AC outlet. 
 
The memory backup circuit begins to function a few minutes after you...

          into the scanner.  Use this procedure only when you are sure the 
          scanner is not working properly. 
 
1.  Turn off the scanner, then turn it on again. 
 
2.  Press and hold down CLEAR and insert a pointed object such as a 
    straightened paper clip into the RESTART hole on the back of the 
    scanner for about 2 seconds.  Information on the scanners display 
    disappears. 
 
3.  When information reappears on the scanners display, release CLEAR. 
 
A LOOK AT THE KEYBOARD 
 
A...

           MONITOR - accesses the 100 monitor memories. 
 
      TUNING Knob - turn to tune through channels or frequencies. 
 
              SCAN - scans through the channels. 
 
            MANUAL - stops scanning to let you directly enter a channel 
                     number. 
 
              TUNE - lets you use the scanners rotary tuner to tune 
                     through frequencies. 
 
           PROGRAM - programs frequencies into channels. 
 
              AUTO - lets you automatically...

 
          PRIORITY - appears when the priority feature is turned on. 
 
               MON - appears with a number (1-100) to show which monitor 
                     memory you are listening to. 
 
          LOCK-OUT - appears when you lock out a channel or manually select 
                     a locked-out channel. 
 
             DELAY - appears when scanning stops at a channel you have 
                     programmed for a 2-second delay. 
 
                AM - appears when the scanner scans a...

MONITOR MEMORIES 
 
TURNING ON THE SCANNER/SETTING VOLUME AND SQUELCH 
 
1.  Turn SQUELCH fully counterclockwise. 
 
2.  Turn VOLUME clockwise until you hear a hissing sound. 
 
3.  Turn SQUELCH clockwise, then leave it set to a point just after the 
    hissing sound stops. 
 
NOTE:  If the scanner picks up unwanted, partial, or very weak 
       transmissions, turn SQUELCH clockwise to decrease the scanners 
       sensitivity to these signals.  If you want to listen to a weak or 
       distant...

PRO-2035 1000-Channel Programmable Home Scanner 
(200-0460)              Operation - Part 2             Faxback Doc. # 16911 
 
SCANNING THE CHANNELS 
 
To begin scanning the channels or to start scanning again after monitoring 
a specific channel, press SCAN.  The scanner scans through all non-locked 
channels in the active banks (see Locking Out Channels). 
 
The scanner scans either up or down through the channels in the activated 
banks.  To change the scanning direction, either press the UP or DOWN...

 
Both MON and the frequency stored in the monitor memory are displayed. 
 
MOVING FREQUENCIES 
 
Moving a Frequency from a Monitor Memory to a Channel 
 
1.  Press PROGRAM. 
 
2.  Use the number keys to enter the channel number where you want to 
    store the monitor frequency, then press PROGRAM. 
 
3.  Press MONITOR.  MON flashes.  Use the number keys to enter the monitor 
    memorys channel number, then press MONITOR.  Or, turn TUNING to select 
    the channel number. 
 
    MON flashes and the...

You can move all stored frequencies within a bank you select from higher 
channels to lower, empty channels.  This helps you group all of the 
frequencies you stored within a bank into consecutive channels.  For 
example, if you stored frequencies in channels 1 through 25, left channels 
26 through 30 empty, then stored more frequencies in channels 30 through 
40, the scanner can move all the frequencies together into channels 1 
through 35. 
 
1.  Press AUTO.  AUTO appears. 
 
2.  Using the number keys,...