Home > Uniden > Communications receiver > Uniden BC 278CLT Vhf Uhf Scanner Owners Manual

Uniden BC 278CLT Vhf Uhf Scanner Owners Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Uniden BC 278CLT Vhf Uhf Scanner Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 50 Uniden manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							28
    3. Press or  to set the desired frequency.    
    The channel number flashes. Continue to
    press 
    or to step through the
    frequencies in 100kHz steps. Or, press and
    hold 
    or to step through the 
    frequencies more quickly until 92.5000MHz 
    appears in the display.
    4. PressEto complete the entry. The channel             
    digits stop flashing.
    5. Adjust the VOLUMEcontrol to a comfortable          
    comfortable listening level.
    Continue to program your favorite radio stations in the other nine FM channels using the above
    example.
    To program the ten AM channels, press RADIO AM/FMto select the AM Mode. The AMicon
    appears in the display. Then repeat Steps 2. through5. You will step through the frequencies in
    10kHz steps.
    To change a programmed Radio Frequency, repeat the steps above using new frequencies.
    BC278clt.qxd  3/8/00  7:34 PM  Page 28 
    						
    							29
    Deleting a Stored Radio Frequency
    If you want to delete a stored frequency, follow these steps:
    Example:Delete the frequency in Channel 9.
    1. Press RADIO AM/FMto enter into the Radio 
    mode.
    2. To select the channel (9), press 9on                  
    the numeric keypad.
    3. Press the 
    or keys until 000.0000appears 
    in the display. (In FM 
    000.0000is between
    i08.0000and 88.0000. In AM 0000is
    between 
    i720and 520.)
    4. Press Eto complete the entry. The channel digits stop flashing.
    5.  The following screen appears.                              
    Direct Channel Access for Radio Stations
    Once the channels are programmed, to directly access the channel, follow these steps:
    1. Press RADIO AM/FMuntil the AMor FMicon that you want appears in the display.
    2.  Press the desired channel number on the keypad. The frequency appears in the display.
    3. Adjust the VOLUMEcontrol for a comfortable listening level.
    BC278clt.qxd  3/8/00  7:34 PM  Page 29 
    						
    							30
    Reset the Clock Time
    1. To reset the clock time, simply press and             
    hold the TIME SETkey. The display digits
    flash.
    2. Enter the time directly by pressing  
    the numeric keys.
    OR  
    Enter the time by pressing the 
    / keys.
    3. Press AM/PMto select the desired setting              
    either a.m. or p.m.
    4. Press Eto complete the entry. The display stops      
    flashing.
    BC278clt.qxd  3/8/00  7:34 PM  Page 30 
    						
    							31
    Set the Alarm Time
    There are two types of alarm sounds with this scanner, Tone Alarm and Radio Alarm. Alarm time is
    set in the same manner for both types of alarm.
    1. After the clock time has been entered,                    
    press and hold ALARM SET until the time
    indicated and ALARMindicator flashes in 
    the display.
    2. Enter the alarm time directly    
    by pressing the numeric keys.
    OR
    Enter the time by pressing the
    /keys. 
    3. Press AM/PMto select the desired setting,             
    either a.m. or p.m.
    BC278clt.qxd  3/8/00  7:34 PM  Page 31 
    						
    							32
    4. Press Eto complete the entry.                           
    5.ALARMindicator and     
    time stop flashing, but
    remain on.
    6. The alarm time remains in the display for five seconds, then returns to current time.
    Set Alarm to Tone Mode
    Press ALARMto turn on the alarm     
    function. The ALARMindicator and
    current alarm time are displayed. 
    When the alarm goes off, it will sound as a series of beeps gradually growing louder. 
    The alarm will continue for approximately 15 minutes if no action is taken. 
    Snooze function
    To silence the alarm, simply press any key. This silences the alarm for about nine minutes.
    You can repeat this cycle for over an hour. The display is backlit for about ten seconds to view
    the current time.
    BC278clt.qxd  3/8/00  7:34 PM  Page 32 
    						
    							33
    Turn the Alarm Off
    Press ALARMto deactivate the alarm 
    function. When the alarm is off, the
    ALARMindicator and current alarm
    time are no longer displayed. Only the 
    current time displays.
    If you find the Tone Alarm too loud, select the Radio Mode instead.
    The volume is adjustable.
    If you would like to listen to the scanner while waking up,  turn the
    scanner on. The snooze function continues to operate while the
    scanner is turned on and in any mode.
    BC278clt.qxd  3/8/00  7:34 PM  Page 33 
    						
    							34
    Set Alarm to Radio Mode
    Before you set the Radio Alarm, make sure an AM or FM channel has been selected and the
    VOLUMEcontrol is set to the desired level.
    You must be in Clock mode(scanner off) to be woken up by the radio alarm.
    1. Press OFF.
    2. Press and hold ALARMfor more      
    than 2 seconds. When the alarm is
    on, the ALARMand RADIOicons
    flash for 5 seconds.
    3. The ALARMremains on.
    When the alarm goes off, it will play the radio station that was previously selected. The alarm will
    continue for approximately 15 minutes, if no action is taken.
    Snooze function
    To silence the alarm, simply press any key. This silences the alarm for about nine minutes. You can
    repeat this cycle for over an hour.
    Turn the Alarm Off
    Press ALARMto turn the alarm off.         
    When the alarm is off, the ALARMicon
    and current alarm time are no longer
    displayed, only the current time is
    displayed.
    BC278clt.qxd  3/8/00  7:34 PM  Page 34 
    						
    							35
    Helpful Hints
    General UseTurn the scanner off before disconnecting the power.Always write down the programmed frequencies in the event of scanner memory loss.
    If scanner memory is lost, simply reprogram each channel. The display shows
    when there has been a memory loss.
    Always press each keypad button firmly until you hear the entry tone for that key.
    Location
    If your scanner receives strong interference or electrical noise, relocate the scanner or its
    antenna away from the source of the noise. A higher elevation may provide better
    reception. Also, try changing the height or angle of the antenna.
    Avoid placing the unit in direct sunlight or near heating elements or vents.Do not plug the scanner into an outlet controlled by a wall switch as prolonged periods
    without power will cause the clock to reset.
    Cleaning
    Disconnect the power to the unit before cleaning.To prevent scratches, do not use abrasive cleaners or solvents. Be careful not to rub the
    display window.
    Do not use excessive amounts of water.
    Repairs
    Do not attempt any repair. The scanner contains no serviceable parts. Contact the
    Uniden Customer Service Center or take it to a qualified repair 
    technician. (Page 37)
    Birdies
    All radios are subject to receiving undesired signals or birdies. If your scanner stops
    during Scan mode and no sound is heard, it may be receiving a birdie. Birdies are
    internally-generated signals inherent in the electronics of the receiver. PressSCANto
    resume scanning.
    If you still cannot get satisfactory results and want additional information, or to return the
    unit for service, please call the Uniden Customers Service Department at the number on 
    Page 37.
    ABOUT THE UNIT
    BC278clt.qxd  3/8/00  7:34 PM  Page 35 
    						
    							36
    ProblemSolution
    Check the connections at both ends of the 
    AC Adapter.
    Turn on the wall switch of your room.
    You could be using an outlet controlled by the
    wall switch.
    Move the AC Adapter to another wall outlet.
    Scanner won’t power up.
    Poor reception.Check antenna connection.
    Move the antenna.
    If the programmed frequency is higher than 
    406MHz, a shorter antenna length may improve 
    the reception.
    Relocate the scanner.
    You may be in a fringe area. This could require 
    an optional multi-band antenna. Check with your 
    dealer or local electronics store.
    Scan won’t start.Press the SCANkey again.
    Adjust the Squelch control.
    Check to see if 100 channels are locked out. If so, 
    unlock the channels as needed.
    If your BC278CLT is not performing properly, try the following steps. 
    TROUBLESHOOTING
    BC278clt.qxd  3/8/00  7:34 PM  Page 36 
    						
    							37
    ProblemSolution
    Scan won’t stop.Adjust squelch to the threshold (Page 9).
    Check the antenna connection.
    Check to see if many of the channels are locked 
    out. If so, the scanner has less chance of finding 
    an active channel.
    Review each channel’s frequency to see if it is 
    correct and no memory has been lost.
    It is possible that none of the programmed 
    frequencies are active at this time.
    Weather Scan 
    won’t work.Adjust squelch to the threshold (Page 9).
    Check the antenna connection.
    It is possible that there are no active stations 
    within range.
    At Uniden, we’ll take care of you!
    If you need any assistance with this product, please call our Customer Hotline at:
    1-800-297-1023
    PLEASE DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
    Our Uniden representatives will be happy to help you with any matters regarding the operation of this
    unit, available accessories, or any other related matters.
    BC278clt.qxd  3/8/00  7:34 PM  Page 37 
    						
    All Uniden manuals Comments (0)

    Related Manuals for Uniden BC 278CLT Vhf Uhf Scanner Owners Manual