TP-Link Router TL-R460 User Manual

TL-R460Cable/DSL Router User Guide
 
 
44
Click the  Previous  button to view the informat ion in the previous screen, click the  Next 
button to view the information in the next screen. 
4.6.4  MAC Filtering 
Choose menu “ Security→MAC Address Filtering ”, you can configure the MAC 
Address filtering rule in the next screen (shown in  Figure 4-34). The MAC Address 
Filtering feature allows you to  control access 

to the Inte rnet by users on your local 
network based on their MAC addresses. 
 
Figure...

TL-R460Cable/DSL Router User Guide
 
 
45
shown in  Figure 4-35. 
Step 3:  Enter the approp
riate MAC address and descr iptions, then select the status as 
shown in  Figure 4-35. 
 
Figure 4-35 
Step 4:  Finally, click  Save to make the rule take effect. 
Step 5:  Go to Step 2  to complete the other rules continually. 
After you finish the configurations, you will see the rules in the table below: 
 
Figure 4-36 
)  Note: 
Before adding a MAC Address Filtering  entry, you should enable the Firewall and...

TL-R460Cable/DSL Router User Guide
 
 
46
 
Figure 4-37 
¾  Web Management Port  -  Web browser access normally uses the standard HTTP 
service port 80. This router’s default  remote management web port number is 80 . 
For greater security, you can change the  remote management web interface to a 
custom port by entering that number in  the box provided. Choose a number 
between 1024 and 65534, but do not use t he number of any common service port. 
¾  Remote Management IP Address  -  This is the current...

TL-R460Cable/DSL Router User Guide
 
 
47
 
Figure 4-38 
¾  Packets Statistic Interval (5 ~ 60)  - The default value is 10. Select a value 
between 5 and 60 seconds in the pull-down  list. The “Packets Statistic interval” 
value indicates the time secti on of the packets statistic. 
¾  DoS Protection  - Enable or disable the DoS protec tion function. Only when it is 
enabled, will the flood filters be effective. 
¾  Enable ICMP-FLOOD Attack Filtering  - Enable or disable the “ICMP-FLOOD 
Attack...

TL-R460Cable/DSL Router User Guide
 
 
48
immediately. 
¾  Enable TCP-SYN-FLOOD Attack Filtering  - Enable or disable the “TCP-SYN- 
FLOOD Attack  Filtering”. 
¾  TCP-SYN-FLOOD Packets Threshold: (5 ~ 3600)  -  The default value is 50. Enter 
a value between 5 ~ 3600 packets/s. When the current number of 
TCP-SYN-FLOOD  Packets is beyond the permitted value, the router will start up 
the blocking function immediately. 
¾  Ignore Ping Packet from WAN Port  - Enable or disable “ignore ping packet from 
WAN...

TL-R460Cable/DSL Router User Guide
 
 
49
Disabled  means the rule is ineffective. 
To add/modify a static routing entry: 
Step 1:  Click Add New… /Modify  shown in  Figure 4-39, you will see a new screen 
shown in  Figure 4-40. 
Step 2:  Enter the a

ppropriate Destination  IP Address, Subnet Mask and Default 
Gateway, and then select the status. 
 
Figure 4-40 
Step 3:  Click Save to make the entry take effect. 
) Note: 
If you want to add more than on e static route, please go to step 1  to continue....

TL-R460Cable/DSL Router User Guide
 
 
50
4.8.1  Binding Setting 
Choose menu “ IP & MAC Binding→ Binding Setting”, you can view and add IP & MAC 
binding entries in the next screen (shown in  Figure 4-42). 
 
Figure 4-42 
¾  MAC Address  -  This field displays the MAC addre ss of the controlled computer in 
the LAN. 
¾  IP Address - This field displays the assigned IP address of the controlled computer 
in the LAN.   
¾  Bind  - Select Whether enable the arp binding  or not. Only bind the MAC address...

TL-R460Cable/DSL Router User Guide
 
 
51
4-44. 
Step 2:  Enter the specific MAC Address or IP  Address in the corresponding field. 
 
Figure 4-44 
Step 3:  Click Find button, then you will see the entry  with the specific MAC address or 
IP address. 
Step 4:  Click Return  to return the previous screen. 
) Note: 
You can click “Turn to this page” to  edit the entry in the corresponding screen. 
Other configurations for the entries as shown in Figure 4-42: 
C

lick the  Delete button to delete the entry....

TL-R460Cable/DSL Router User Guide
 
 
52
 
Figure 4-45 
Click  Load  to load the specific item to  the IP & MAC Binding list (shown in  Figure 4-42). 
C

lick Delete to load the specific item  to the IP & MAC Binding list. 
Click the  Bind All button to bind all the current items, available after enable. 
Click the  Load All button to load all items to the IP & MAC Binding list (shown in  Figure 
4-42

). 
Click the  Refresh button to refresh all items. 
) Note: 
An item could not be loaded to the IP &...

TL-R460Cable/DSL Router User Guide
 
 
53
 
Figure 4-46 
¾  Connection Status -  The status of the DDNS service is displayed here. 
To set up for Dyndns DDNS, follow these instructions: 
Step 1:  Type the “User Name” and “Password” for your DDNS account. 
Step 2:  Enter the domain name your dynamic  DNS service provider offer. 
Step 3:  Enable DDNS, and click  Save to save the current configuration. 
Click Login  to login the DDNS service. 
Click Logout to logout the DDNS service. 
4.9.2  PeanutHull DDNS...