Toshiba Tdp Tw95 Projector User Manual

							21
20
Preparations
Placement StylesAs shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the
Default setting menu 
p.41
, in accordance with your needs.
Placement
 WARNING
•Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus
resulting in injury.
•If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the
projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.
Improper mounting could cause the projector to fall, resulting in an accident.
•If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let
everyone involved with the use of the projector know that fact.Floor-mounted front projection 
Floor-mounted rear projection 
Ceiling-mounted front projection 
Ceiling-mounted rear projection 
Operating a computer using the remote controlA computer can be operated using the projector’s remote control.  This function is available
on any computer with the Windows
® 98/98SE, Windows
® Me, Windows
® 2000, or Win-
dows
® XP OS, that is equipped with a USB port which can support USB1.1 (The mouse
remote control receiver is also supported on OS 9 or OS X for the Macintosh).  However,
please note that Toshiba does not guarantee the operation of all computers.
1
Connecting a computerConnect the mouse remote control receiver (supplied) to a computer.Mouse remote control receiverTo USB port2
Operating a computerOperate remote control’s buttons towards the mouse remote control receiver.
●Moving the mouse pointer
Press the mouse control button in the direction you wish the mouse pointer to move,
then press.
●To left click
Press the L-CLICK button.
●To right click
Press the R-CLICK button.
●To drag and drop
Holding down the L-CLICK button, move the mouse control button until the mouse
pointer is over the desired location, then release the L-CLICK button.
●Using the computer’s page up [
↑] and down [
↓] function
Press the PAGE+ and PAGE- buttons to switch PowerPoint
® slides.
The remote control may fail to operate
if the mouse remote control receiver is
exposed to bright sunlight or
fluorescent lighting.
In such a case, change position or
direction of the mouse remote control
receiver and retry.
Mouse control
Remote Control Front Remote Control Rear
PAGE –
PAGE +
R-CLICKL-CLICK
Projection Distance and SizeUse the figures, tables, and formulas below to determine the projection size and projection
distance. (Projection sizes are approximate values for full-size picture with no keystone
adjustment.)Screen
As seen from above
As seen from the side
90°
 
a 90°
Lens center
a (min length) = projection size (inches) – 1.0437
26.957
a (max length) = projection size (inches) – 0.6246
16.749
a is the distance (m) between the lens and the screen, and
corresponds to a range of 1.07 m to 11.09 m.
projectionprojection distance a (m)
min length max lengthsize (inches)
(zooming max) (zooming min)
30 1.07 1.7540 1.45 2.3560 2.19 3.5580 2.93 4.74100 3.67 5.93150 5.53 8.92200 7.38 –250 9.24–
300 11.09– 
						

							23 22
Preparations
p.89
Audio amplifier, etc. DVD video recorder, etc.Video recorder,
DVD player, etc.
Video recorder, etc.
Conversion
adapter BNC-pin
(not supplied)
Monitor cable Mini
D-sub 15P-BNC
(not supplied)
To audio input
White (L)/Red (R)To audio
output
White (L)/
Red (R)
AV  cable
(not supplied)S-video cable
(not supplied)To S-video
output
To video
output
Before connection•Read the owner’s manual of the device you are connecting to the projector.
•Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal 
p.87
, etc.
•Turn off the power of both devices before connecting.
•The figure is a sample connection. This does not mean that all of these devices can or
must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Notes
•The COMPUTER 1 IN terminal functions identically to the COMPUTER 2 IN terminal.
•The MONITOR OUT terminal outputs signals from the COMPUTER 1 IN terminal or the
COMPUTER 2 IN terminal, or outputs Y/P
B/PR as selected with the INPUT button. If no
input is selected, the MONITOR OUT terminal outputs the input signals last selected for
each input terminal
•Signals are output from MONITOR OUT terminal even in standby mode.
   However, from AUDIO OUT terminal, no audio signal is output.
•A computer monitor cannot accept Y/P
B/PR signals correctly.
•The AUDIO IN terminal doubles for devices connected to COMPUTER terminals 1 and 2.
•When an AUDIO OUT terminal is connected, sound is not output from the projector
speaker.
•Output volume of AUDIO OUT terminal can be adjusted by the VOL button.
•Moving pictures played back on computers using DVD software may appear unnatural if it
is projected with this projector, but it is not a malfunction.
Connection
Computer
(for control)Computer
To
RS-232C
terminal
Audio cable
(not supplied)To audio
output
Control cable
RGB cable
(supplied)To  RGB
output
Computer
Audio cable
(not supplied)
Audio cable
(not supplied)
To audio
output
To  Y/C
B/CR
output
Green (Y)/Blue
(CB)/Red (C
R)
To audio output
White (L)/Red (R)
Audio cable
(not supplied)To audio
output
Audio cable
(not supplied)
RGB cable
(not supplied)To  RGB
output 
						

							25
Operations
24
Notes
•The start-up screen will disappear after a moment. You can dismiss the star t-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu 
p.38
.
•The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed 
p.26
.
•When [Key lock] is [On], the operation buttons of the projector do not work 
p.43
.
•When [Password] is [On], enter password then the start-up screen is displayed after the
Password entry screen disappears 
p.33
.
■Turning the power off1
Press the ON/STANDBY button.A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
A
B
C
A
During cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on.
If you are in a hurry, there is no problem with unplugging the power cord in this
state.
B
After the LAMP indicator goes off, the FAN indicator keeps lighted and the
cooling fan continues to operate for a short while, in order to expel excess
internal heat.
C
In standby mode
Note
•The projector consumes about 9W of power in standby. We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
(When [Wireless standby] is [On], it consumes about 12W during standby.)
PRECAUTION
•If the power cord is unplugged before cooling is complete, give the lamp time (about 5
minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light.
When cooling lamp During internal cooling After cooling complete
Turning the power on and offOperations
■Connecting the power cord1
Insert the power cord connector into
the AC IN socket of the projector.
2
Insert the power cord plug into a
wall or other power outlet.The ON/STANDBY indicator will
change to orange, indicating standby
mode.
■Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.
■Turning the power on
Press the ON/STANDBY
button.
The power turns on, and the following
3 green indicators light: ON/STANDBY,
LAMP, and FAN. After a moment, the
start-up screen appears. CAUTION
•Do not look into the lens while the lamp is on.  The strong light from the lamp may cause
damage to your eyes or sight.
•Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheat-
ing.
•Do not place your hands, face, or other objects near the air exhaust. Doing so could cause
burns, deform/break the object.
Power cord connector
(Supplied)
Start-up screen Control panelRemote
Control 
						

							27
Operations
26
5
Projector placement angle adjustmentsThe placement angle and the height of the projected image can be adjusted by the foot
adjuster.qLift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
wTo fine adjust the angle, twist the
foot adjuster.
eTo adjust the horizontal angle, use
the right and left tilt adjusters.•To stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector.
6
Adjusting the screen size and focusq
Use the ZOOM button to adjust the screen size.
w
Use the FOCUS button to adjust the screen focus.
7
Adjusting the volume with the 
 
buttonsThe speaker volume can be adjusted when an audio signal is being input.Notes
•While a text entry screen (e.g., the Password entry screen) is displayed, the remote
control’s FOCUS and ZOOM buttons function as numeric keys, and therefore cannot be
used to adjust the screen size or focus. In such a case, use the FOCUS and ZOOM
buttons on the projector to make adjustment or retry after quitting the text entry screen.
•Note that lamp characteristics may rarely cause the brightness to fluctuate slightly.
•A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out.  This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
•The DMD
TM is made using extremely advanced technology, but there may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.  Please
note that these are not malfunctions.
•Although this projector supports a wide range of RGB signals 
p.87
, any resolutions not
supported by this projector (XGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, it is recommended that the computer’s
external output should be set to XGA resolution.
•With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
•If no signal is being input from the connected equipment or signal input is stopped while
projecting, the “No signal” will appear.
•If a signal not supported by the projector is input, the “Unsupport signal” will appear.
•If an unavailable operation button is pressed, the 
 icon will appear.
1
2
3
3
Control panelRemote
Control
1
Turn on the power.Turn on the power by following the instructions in “Turning the power on” 
p.24
.
The Easy setup function works to automatically adjust the screen focus and correct the
keystone distortion. If RGB signals are input, auto-setting is also made. This operation
does not take place when [Easy setup] in the Default setting menu is [Off] 
p.41
.
2
 Select the language and the lamp power (When using the
first time).When the projector is used for the first time after purchase, the start menu for lan-
guage (to display the menus and messages on the screen) and lamp power selection
and configuration is displayed in English. (If the screen is out of focus, adjust it
according to the step 
6.)
qUse the 
 or 
 button to select the
desired language and press the 
 button.
Message for setup confirmation is displayed in a
selected language.
Then, the menu for lamp power selection and
configuration is displayed. It is automatically set as
Standard. To change the setting, follow the step w.
wUse the 
 or 
 button to select the lamp
power and press the 
 button.
The lamp power, if selected, will be toggled without
pressing the 
 button. The display automatically
disappears in a few seconds.
Notes•When the projector is turned on the next time, the start menu does not appear upon
startup. However, if [Reset all] is executed from the Default setting menu 
p.41
, the
start menu will be displayed the next time when the power is turned on.
•The language can also be set via the Display setting menu 
p.38
 and Lamp power
via the Default setting menu 
p.41
.
•This owner’s manual assumes that English has been selected.
3
Activate the connected device.Turn on and start the connected device such as a computer.
4
Press the INPUT button.An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.Notes
•When [Auto input search] is set to [Off] in the Default setting menu 
p.41
 (factory
setting is [On]), the Input select menu appears if you press the INPUT button 
p.42
.
•If no signal is being output from the connected equipment, pressing the INPUT button
does not change the input and “There is no other input signal.” will appear.
Basic operations
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Polish
Japanese
Chinese (simplified)
Chinese (traditional)
Korean 
						

							29
Operations
28
■Using auto setting 
(Only for input from computer)
This function automatically adjusts the projector settings such as
sampling phase, frequency, screen position, and clamp for each
type of the input signal by using simple operations.
Press the remote control’s AUTO SET button.For computer input, the 
 icon will appear during processing.
You can set as well by selecting [Auto setting] in the Image
adjustment menu 
p.36
.
Notes•The image may not be projected or auto adjustment/setting may not be performed
correctly for input signals other than those supported by the projector 
p.87
, p.88
.
•If auto setting fails adjustment, adjust manually with [Position] in the Image
adjustment menu 
p.36
.
■Correcting the keystone distortion
When the projector placement angle against the
screen is changed while projecting the image,
the picture will undergo keystone (trapezoidal)
distortion.This projector is capable of correcting this keystone
distortion
.
1
Press the KEYSTONE button.The Keystone menu appears. By default, [Auto v-keystone] is selected.
Item Description
Automatically corrects the vertical distortion.
Press      .
Screen shrinking at Screen shrinking at 
bottom top
Auto  v-keystone
V-keystone
Using handy features
Control panelRemote
Control
Before correction
After correction
Remote
Control
■Easy setup
This function automatically adjusts the screen focus and corrects the keystone distor-
tion (Auto focus and Auto keystone functions).
Press the EASY SETUP button on the
projector or on the remote control.The icon 
 will appear during processing.
•Before pressing the EASY SETUP button, be
sure to set Auto focus and select the items to
be adjusted by Auto adjustment 
p.41
.
•With [Power on Easy setup] in the Default
setting menu set to [On], the screen focus is
automatically adjusted and the keystone
distortion (vertical) is corrected when the
power is turned on.
(Automatic keystone distortion correction and
auto-setting are selected by factory setting.)
•The following screen appears during Auto
focus.
Note•A message appears on the screen if the auto-adjustment fails.Precautions•Auto focus function is effective for projection distance from 1.1 m (30 inch at
maximum zoom) to 5.5 m (150 inch at maximum zoom).
•Depending on the room temperature and brightness as well as the projected image
condition and the projecting surface condition and material, the adjustment may not
be properly made. When such a case arises, adjust the screen focus manually.
•Improper adjustment or correction may also occur if the AF sensor is obstructed or
the window gets dirty. Remove the obstruction and clean the AF sensor window in
such a case.
•After performing Easy setup at power-on, the projected image may appear to be out
of focus after a while. In that case, perform Easy setup again.
•Avoid impact on the projector. Otherwise, Auto focus may not work properly.
Control panelRemote
Control 
						

							31
Operations
30
Remote
Control
3
To move the area to zoom in, use the 
 
 
 
buttons.You can keep pressing.
4
To reset the zoom, press the RETURN button.The image is reset to the original size.Notes•The 
 icon appears while resizing.
•Operating a function other than Mute will release resizing.
•As zooming is processed digitally, the image quality is degraded in larger zoom
ratio.
•During resizing or moving the zooming area, the image may be distorted.
■Cutting off the picture and sound temporarily (Mute)
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be
turned off.
Press the remote control’s MUTE button.The picture and sound are cut off. (The Mute function is released
when pressing the MUTE button again.)Notes•The 
 icon will appear while mute is in effect.
•Operating any other functions will also cancel the muting.
■Changing picture mode
The projected image mode can be selected.
Press the remote control’s PICTURE button.1
The Picture mode menu appears.When connected with computer or USB device 1/2/3/4/5
When connected with video equipment  1/2/3
2
Select a mode using 
 
 then press 
.
Though the 
 button is not pressed, the picture mode
changes as the setting is changed and the display turns off
automatically in a few seconds.
Note•[Picture mode] of the Image adjustment menu has the same
function 
p.36
.
Remote
Control
Using handy features (Continued)
Adjusting Keystone distortion [Auto]2
Press the 
 button.
The keystone distortion is automatically corrected. The 
 icon appears during this
correction.
When adjustment is finished, the Keystone menu appears again. For fine adjust-
ment, select [V-keystone] by the 
 button and adjust image manually by the 
 buttons.
Adjusting Keystone distortion [Manual]1
Press the KEYSTONE button.
2
Select [V-keystone] by the 
 button.
3
Use the 
 
 buttons for keystone adjustment.
Notes•A message appears on the screen if the automatic vertical keystone distortion
correction fails
.
•Depending on the amount of keystone adjustment and the content of images, some
information may be lost, or the picture quality may suffer.
Precaution•Depending on the room temperature and brightness, the placement as well as the
projecting surface condition and material, the correction may not be properly made.
When such a case arises, make correction manually.
■Resizing image
The projected image can be resized (zoomed in/out).1
Press the remote control’s RESIZE 
 button.
Each time you press the RESIZE 
 button, zoom ratio is up. You can keep
pressing.
2
To zoom out, press the remote control’s RESIZE
 button.
Each time you press the RESIZE 
 button, zoom ratio is
down. You can keep pressing.
(However, the image cannot be smaller than the original
size.)
Remote
Control 
						

							33
Operations
32
■Password function
When the password function is added and [Password] is set to [On], image projection
requires an entry of the preset password at power-on.
To add the password function, perform the following procedure:
(The password function, once added, cannot be deleted. Set [Password] to [Off] if you
do not want to use it after addition.)
Notes: • This password is different from that for the wireless LAN.
•When adding the password function, switch the input to other than Wireless or
USB.
How to add password
1
Set the projector to the operating status or the standby mode.
2
Select and hold the 
 button until the LAMP, TEMP, and FAN
indicators light in orange.
The password function is added when the steps up to here have been completed. It
is also added to the Default setting menu.How to set password (from [Off] to [On])
1
Select [Password] in the Default setting menu and press the 
 or 
button.The password setting confirmation screen is displayed. ([OK] or [Cancel])
2
Select [On] and press the 
 button.
The password entry screen is displayed.
3
Enter a four-digit number for the password using numeric keys of the
remote control.The input number appears as [****].
4
Re-enter the same password for confirmation.When the password is confirmed, the setting is complete and the password
becomes [On].
If the password is wrong, repeat the procedure from step 
2.
How to operate when password is [On]
1
Turn on the power.
2
The lamp lights and the password entry screen appears.
3
Enter the password using numeric keys of the remote control.If the entered password is correct, the start-up screen appears and the projector
goes into normal operation. If the password is wrong, a message appears to
prompt you to re-enter the password, and again the password entry screen is
displayed. If you enter a wrong password for more than 5 times, the projector will
automatically power off and enter standby mode.
Using handy features (Continued)■Changing screen size
The screen size for the projected image can be changed.
Press the remote control’s SCREEN SIZE button.Pressing the button switches Full/Thru/Wide in turn.Notes•Thru display is available for computer-input images.
•[Screen size] of the Display setting menu has the same functionp.38
.
•If you use this function on commercial video software, broadcast
or cable-broadcasting except for the purpose of your private
viewing and listening, it may infringe the copyright protected by
the copyright laws.
■Freezing the image (Freeze)
The image being projected can be frozen. This function is to be used
to pause a video during a presentation, etc.
Press the remote control’s FREEZE button.The picture pauses. (The Freeze function is released when
pressing the FREEZE button again.)Notes•The 
 icon will appear while freeze is in effect.
•Other operation will also release the freeze.
•Even if an image is frozen on the projector, the pictures are
running on the video or other equipment.
•If you use this function on commercial video software, broadcast
or cable-broadcasting except for the purpose of your private
viewing and listening, it may infringe the copyright protected by
the copyright laws.
Remote
ControlRemote
Control 
						

							35
Operations
34
You can call up on-screen menus, and conduct a number of adjustments and settings using
the operation buttons 
p.16
 on the control panel (main unit side) and remote control.
■How to use the menus
The menu shown below is for operation instructions purposes and might differ from the
actual display.
Using the menus
Toggle items with            . 
Select items with             and press       . 
Fix selection with       .
Display the Setting display menu.
1. Press the MENU button
2. Select a Category
3. Adjustments & SettingsSelect a category by using  
         .
There are following four 
categories:Displays the current 
adjustments and 
settings of selected 
category.
Item shown with gray 
cannot be adjusted with 
the current input source.p.36
Image adjustment menu
p.38
Display setting menu
Default setting menu
p.41
•The figure shows displays given for operation instructions purposes.  As the display may differ depending on the item, 
use the following pages as a reference.
•To return to previous item, press the RETURN button.
•When Wireless/USB input is selected, pressing the MENU button displays the Setting display (2) menu.
Item
Adjustment/Setting ValueThese marks signify 
the items can be 
adjusted/set by using
            
.
These marks signify the items can 
be selected from the list by using
            .
After an item is selected, apply it by 
pressing       .
Press       or       to open the menu.
Status display menu
p.44
These marks 
signify that there 
are options. 
Press        or         
to display a list of 
options.
These marks 
signify that 
there are setting 
screens. Press 
       or       to 
display a list of 
setting screens.
* When no item is 
changed, press       .
4. EndPress the MENU button once more.
(The menu disappears 30 seconds after the last operation.)
How to cancel password (from [On] to [Off])
1
Select [Password] in the Default setting menu and press the 
 or 
button.The password entry screen is displayed.
2
Enter the password using numeric keys of the remote control.
3
The password cancel confirmation screen is displayed. ([OK] or
[Cancel])
4
Select [OK] and press the 
 button.
The [Password] is canceled and becomes [Off].Note•The password entry screen appears when the power is turned back on only after
the power cord is unplugged.You cannot release password by yourself. If you forgot password,
please inquire your dealer.
Using handy features (Continued) 
						

							37
Operations
36
Item 
  
Description
Computer Y/P
B/PRVideo
S-videoWireless/
USB
Position
 FrequencyYe s N o NoNo No
Adjust to eliminate periodic patterns and
flickering when many fine vertical lines
appear on the screen. H-positionYe s N o NoNo No
Adjust the horizontal position of the image. V-positionYe s N o NoNo No
Adjust the vertical position of the image. Clamp 1Ye s N o NoNo No
Adjusts the clamp pulse position. Clamp 2Ye s N o NoNo No
Adjusts the clamp pulse width.
*1: [Noise reduction] may not work depending on signal type.
*2: [[NTSC mode] can be displayed and adjusted only when the video signal is set to [NTSC] or
[NTSC4.43]. NTSC mode is set to JAPAN when the language is set to Japanese. It is set to US for
other languages.
Using the menus (Continued)■The image adjustment menuUse this menu to set or adjust image-related items. Items that can be set or adjusted are
marked with “Yes”, and those that cannot are marked with “No”. (When an item is masked,
it indicates that you cannot select for the current input.)
Item 
  
Description
Computer Y/P
B/PRVideo
S-videoWireless/
USB
 
ContrastAdjust the image contrast. Yes Yes Yes Yes Yes
Lower
Higher
BrightnessAdjust the brightness of the image. Yes Yes Yes Yes Yes
Darker
Brighter
ColorAdjust the color of the image. No Yes Yes Yes No
Lighter
Deeper
SharpnessAdjust the sharpness of the image. No Yes Yes Yes No
Softer
Sharper
NoiseSet the function to reduce screen noise. No Yes Yes Yes No
reduction
*1
On (Enable)
Off (Disable)
Picture modePress 
. Toggle the picture mode with No Yes Yes Yes No
 
.
1/2/3
1/2/3/4/5 Yes No No No Yes
/
/
R-levelAdjust red of the image color. Yes Yes Yes Yes Yes
Less red
More red
G-levelAdjust green of the image color. Yes Yes Yes Yes Yes
Less green
More green
B-levelAdjust blue of the image color. Yes Yes Yes Yes Yes
Less blue
More blue
NTSC mode
*2
Set the black level with 
 
.NoNoYesYesNo
US:NTSC (US) mode
JAPAN:NTSC (JAPAN) mode
 Auto settingAutomatically adjusts items such as the Yes No No No No
samplingphase depending on the type of
input signal.PositionPress 
 then change mode using 
 
Ye s N o NoNo No
and adjust with 
 
.
 PhaseYe s N o NoNo No
Adjust to eliminate flicker. 
						

							39
Operations
38
Note
•If you use the screen size setting function on commercial video software,
broadcast or cable-broadcasting programs to display images with the varying
aspect ratio except for the purpose of your private viewing and listening, it may
infringe the copyright protected by the copyright laws.[Blackboard mode]Projects the image in colors more like projecting on a screen.
Precaution•The projected image may differ depending on the type, color, and material of the
blackboard and wall even if the selected color is the same as the projected
screen.[Background]•TOSHIBA is set for [Logo] by factory setting.
•If user’s logo has been registered, it is displayed when [Logo] is set for
background.[Start-up screen]If user’s logo has been registered and this setting is [On], the logo is displayed at
start-up.[User logo]Registers a part of the image that is input from computer, as a stationary picture
and displays it as a logo at start-up and when no signal is input.
How to register user logo1
Select [User logo] in the Display setting menu, and press the or 
 button.
2
Select  from the displayed menu list and
press the 
 button.
3
The registration area is displayed for confirmation. Select [OK]
or [Cancel] and press the 
 button.
•If the registered picture does not fall within the display area, operate the
computer to scroll the screen.
4
Select [Yes] to register and press the 
 button.
5
Registration starts.•A message is displayed while registration is in process.
Using the menus (Continued)■The display setting menuUse this menu to set screen display-related items.
(The items in gray color cannot be set with the current input selection.)
(Full):  Display with 1024 × 768 dot resolution
(Thru): 
Display with sampling resolution (Disabled for the video input)
(Wide):  Wide-screen display (Disabled for the wireless/USB input)
When projecting on a non-screen surface, select a color in accordance 
with the projecting surface.
Press      and switch with       and      .  
Off/Green/Black/Brown/Blue/Beige
Select one of the languages below to use for displaying the menu and messages[      or      : Enter setting mode]     [          :Selection]      [Apply:       ]
English/Français/Deutsch/Italiano/Español/Português/               /
Svenska/Türkçe/Polski/            /                      /                      /
Screen to display when there is no input signal
[      or      : Enter setting mode]     [          :Selection]      [Apply:       ]
Logo/Blue/None
Display icons as function guidesOn Off
Display start-up screen when power is turned onOn Off
Display a logo customized by the user for the start-up screen or when 
there is no input signal.
[      or      : Enter setting mode]     [          : Selection]
      Logo registration Press       to display the registration menu.
      Display style
      BackgroundBlack           Blue           White
      Logo confirmation Press      .
      Reset logoYes           NoDescription
Item
Screen size
Language
Background
IconBlackboard 
modeStart-up screen
User logo
Detailed description
[Screen size]•If “Thru” is selected for [Screen size], portions exceeding the native resolution
(1024 × 768 pixels) will not appear on the screen. Note that for RGB signals with
clock frequency 140MHz or lower, all input pixel signals are sampled. However, if
the clock speed is higher than this, the RGB pixel signal is thinned before
sampling.
•The wireless/USB input can be selected only when the wireless LAN USB
adapter is connected to the projector. Selecting the “Full” mode allows the display
in the same aspect ratio with that for the video signal.