Toshiba Tdp Tw100u Projector User Manual

							61
Operations
60
Checking the projector status■Status display
To check the current status of the projector, select Status display in step 2 in
“Projector settings” 
p.48
. The following items of information will then be displayed.
ApplicationThe name of the application currently running on the projector is
displayed.
(Examples: Slideshow, Wireless Utility)
Device
When no device is plugged
“Type” is displayed.
When USB memory is plugged“Type
/Free space/Status” are displayed.
When a wireless LAN USB adapter is plugged
“
Type
/MAC address/Mode/Channel/SSID/Encryption/IP address/
Subnet mask/Gateway” are displayed.
VersionThe firmware version number of the wireless/USB feature is
displayed.Note
•This product contains a piece of software (hereafter the Software) licensed to TOSHIBA
CORPORATION (hereafter TOSHIBA) by AXE, Inc. (hereafter AXE). The copyright and
other intellectual property rights of the software are held by AXE or the licensor.
The software is protected by the Copyright Law, Universal Copyright Convention, and
other intellectual property laws and agreements. The permission of AXE or the licensor
must therefore be obtained before the software can be reproduced.
Note, however, that the software is partly covered under the GNU General Public License
Version 2 (hereafter GPL2). You can obtain a copy of GPL2 at http://www.fsf.org/copyleft/
gpl.html. AXE will provide the GPL-covered source code of the software in accordance
with the terms of GPL2. Contact AXE if you need it.
Software: axLinux is a registered trademark of AXE, Inc.
■The control setting menu
This menu unplugs a USB device and sets Email function. Select Control setting in
step 2 in “Projector settings” 
p.48
. The following content will be displayed.
Run when unplugging a USB device.
Yes           No
[      : E-mail setting]      [           : Select item]
Status notification: On           Off
SMTP server: Enter a character string using numeric keys of the 
remote control.
Port number: Enter a character string using numeric keys of the 
remote control.
Destination address: Enter a character string using numeric 
keys of the remote control.
Confirm: [OK           Cancel] Description
Item
Email
Unplug device
●Detailed description•[Unplug device]
Run when unplugging a wireless LAN USB adapter, a USB memory, a USB memory
card reader or a digital camera and the like.
•[Email]
: Sends alarm information to the specified E-mail address when
an error such as lamp blowout occurs.
: Set an IP address of the SMTP server.
: Enter a port number of the SMTP server.
: Enter within 60 characters. (Example: [email protected])Note
•The Email function does not support transmission to the SMTP server that requires
authentication.Control setting 
						

							63
Operations
62
Using the Wireless Utility■Displaying a computer’s screen via the projector1
Launch the Wireless Utility
software application.When the  Wireless Utility  launches, the Screen
Image  transmission mode window appears on
the computer screen.
To  switch to the  Screen Image  transmission
mode window from another mode, click on the
Screen Image  icon 
.
2
Select Transmission mode.Click on Update automatically  or Update manually . See step 
6 for the meanings of
Update automatically  and Update manually .
3
Click on the Advanced button.The Screen Image: Advanced Settings  dialog
appears. Set the dialog as shown below, as
necessary.
• Interruption
Check the  No Interruptions  checkbox to prevent
other computers from interrupting the projector, for
e xample, during presentation in the  Update
automatically  mode.
• W indow
Select the  Place in Tasktray at the start of
transmission  checkbox to iconify the  Wireless
Utility  and place it in the computer’s tasktray
when transmission initiated.
To  display the window, double click on this icon, or
r ight click and select  Open from the popup menu.
Even with the  Wireless Utility  window minimized,
y ou can use the pop-up menu to stop or resume
transmission as described in step 
4 and later
• Transmission Mode (Image)
Selecting  High quality  improves the quality of the
projected image, but lowers communication
speed. Selecting  High speed has the opposite
effect.
• Transmission Mode (Sound)
Check the  Transmit sound to a projector (Only when connected with only one
projector)  checkbox to transmit the sound being played on a computer to the projector.
Note: The sound can be sent when only one projector is selected.
Installing the applicationsIf you will use the wireless LAN USB adapter function, install the applicati\
on on the
supplied CD-ROM onto your computer.■ System Requirements
Supported OS: Windows
® 2000, Windows
® XP (Windows
® 98SE and
Windows
® ME are supported by JPEG Conversion Tool.)
CPU: P entium M 1 GHz or higher recommended
RAM: 256 MB or more recommended
Screen area (resolution): 1024 by 768 pixels recommended
* The system requirements may vary depending on the conditions of use.
■ Application Types and Major Functions
Wireless UtilityThis application is used for wireless connections. Use it to send the images from the
computer’s screen to your projector, and display on the screen. In addition, also use it to
transmit the sound being played on a computer to the projector.JPEG Conversion ToolUse to convert JPEG and other files into a format that can be displayed as a slide show
using a USB memory.
■ How to install
In the supplied CD-ROM, select the  Wireless Utility  folder and the  JPEG Conversion
T ool  folder, and run  setup.exe, respectively. Follow the instructions on your computer
screen.
During the installation, a dialog box may appear with the message “ Digital Signature
Not Found ” and the prompt “ Do you want to continue the installation? ”. Click on the
[ Y es (Y) ] button to continue the installation.
When installation is finished, the following shortcuts will appear on your computer’s
desktop:
W ireless Utility  →
Operations 
p.63
JPEG Conversion Tool  →
Operations 
p.74
■ How to uninstall
Select [ Start Menu ] →  [Settings ] →  [Control Panel ] →  [Add/Remove Programs ],
and remove  Toshiba Data Projector  and JPEG Conversion Tool  from currently
installed programs.Notes
•Y our computer screen may temporarily go out during installation, but it is not an errors.
• Before beginning installation or uninstallation, you need to log on as Administrator. 
						

							65
Operations
64
Using the Wireless Utility (Continued)
•If no sound can be heard from the computer though the connection is stopped, re-launch
the application that plays the contents including the sound.
•Transmission may not be available depending on the sound type.
•Sound cannot be transmitted if multiple projectors are selected.
•The audio signals transmitted by a computer become mono.■
Displaying a JPEG image saved on a computer via the projector
1
Launch the Wireless Utility software application.The Screen Image transmission mode window appears on the computer’s screen.
2
Click on the JPEG File icon 
.
The Wireless Utility window changes to JPEG
File transmission mode.
3
Click on the Browse button, and
select the file to send.Clicking on the Browse button displays the Open
dialog box. Select the file to send, then click on the
Open button.
The selected file is added to the pull-down list in the
Wireless Utility’s Transmission File field.
4
Select the file to be sent from the
pull-down list of the Transmission
File field.Click on the Transmission File field’s 
 button to
display the pull-down list. Select the file to be sent
from this list.
A thumbnail of the selected file appears in the
Preview box. The file displayed here will be
transmitted.
Step 
3 can be skipped.
The way that drag and drop the file to be sent from the desktop or Windows Explorer
into the Preview box is also available. In this case as well, the selected file is added to
the file pull-down list Transmission File field’s.
4
Select the screen image you wish
the projector to display.Select Desktop
The computer screen image is transmitted as-is
.
Select application window
Select a running application (e.g. Microsoft
®
PowerPoint
®), and send that application’s
window only.
The desktop and a list of running applications are displayed.
Select the desired application from this list. (If the desired
application is not on the list, launch it. Note that if too many
applications are running, it will consume the computer’s
resources, which could slow communication speed.)
5
Select the projector to be
transmitted.The IDs of projectors accessible for transmission
will be listed. (When a projector name is set, that
name appears instead of MAC address.) Select the
checkbox of the projector you wish to transmit to
from this list. Then icon 
 is displayed on the
projector’s screen for few seconds
.
It is possible to select up-to four projectors.
6
Click on the 
 button.
When “Update automatically” is selected in step 
2
Screen images are sent consecutively after the 
 button is clicked. Besides,
the sound being played on a computer can be sent to the projector.
When “Update manually” is selected in step 
2
A single screen image is sent when the 
 button is clicked.
7
To halt transmission from Update automatically, click on the
 button.
If the Wireless Utility icon has been placed in the tasktray, double click on the icon to
display the window, then halt transmission, or right click on the icon, and halt transmission
.
Notes
•It may not be possible to transmit the images from movie player or other video applications
.
•When using “Update automatically”, the transmitted image refresh rate depends on the
performance of the computer you are using and the surrounding radio wave environment.
•The projector screen may have a few differences from the computer screen.
•If you selected application window in step  
4, if that application is not active (in use), the
image may not be correctly displayed by the projector.
•
The projector ID is the MAC address of the wireless LAN USB adapter inserted into the projector.•Playing contents protected by copyright is not supported.
•To transmit sound, press the 
 button then launch the application that plays the
contents including the sound. 
						

							67
Operations
66
•Autostart
Check the  Start playing the file automatically when starting transmission  checkbox
to automatically start playing the video file when connecting to the projector.
• Repeat
Check the  Play repeatedly after the end of playing  checkbox to automatically repeat
from the beginning when the file reaches the end.4
Click on the Browse button and
select the file to send.Clicking on the  Browse button displays the  Open
dialog box. Select the file to send then click on the
Open  button.
The selected file is added to the pull-down list in the
W ireless Utility’s Select file  field.
5
Select the file to send from the pull-
down list of the Transmission File
field.Click on the Transmission File  field’s 
 button to
display the pull-down list. Select the file to send
from this list.
A thumbnail of the selected file appears in the
Preview  box. The file displayed here will be
transmitted.
Step 
4  can be skipped.
The way that drag and drop the file to send from the desktop or Windows Explorer into
the  Preview  box is also available. In this case as well, the selected file is added to the
pull-down list.
6
Select the projector to transmit
to.The IDs of projectors accessible for transmission
will be listed. (If projector name has been set up
already, it is shown.) Select the checkbox of the
projector to be transmitted to from this list. Then
icon 
 is displayed on the projectors screen
f or few seconds.
It is possible to select only one projector.
5
Select the projector to be
transmitted.The IDs of projectors accessible for transmission
will be listed. (If projector name has been set up
already, it is shown instead of the MAC address.)
Select the checkbox of the projector to be
transmitted to from this list. Then icon 
 is
displayed on the projector’s screen for few
seconds.
It is possible to select up-to four projectors.
6
Click on the 
 button.
The selected file’s image is displayed by the projector.Note
•Only one file can be sent at a time. To send another file, repeat steps 
4 and 
6.
■ Displaying a video file saved on a computer via the projector1
Launch the Wireless Utility software application.The  Screen Image  transmission mode window appears on the computers screen.
2
Click on the 
 icon.
The Wireless Utility  window changes to  Movie
File  transmission mode.
3
Click on the Advanced button.The Movie file: Advanced Settings  dialog
appears. Set the dialog as shown below, as
necessary.
• Interruption
Check the  No Interruptions  checkbox to prevent
other computers from interrupting the projector, for
e xample, during presentation in the  Update
automatically  mode.
• Transmission Mode (Sound)
Check the  Transmit sound to a projector (Only
when connected with only one projector)
checkbox to transmit the sound being played on a
computer to the projector.
Using the Wireless Utility (Continued) 
						

							69
Operations
68
Using the Wireless Utility (Continued)
●How to set up a simple 1:1 connection•Setting on the projector1
Turn the projector power on.
2
Insert the supplied wireless LAN USB adapter.
3
Switch the input to Wireless/USB.
4
Press the 
 button on the projector control panel.
•Setting on the computer5
Launch the Wireless Utility software
application.When the Wireless Utility launches, the
Screen Image transmission mode window
appears on the computer screen.
6
Click the Tool button 
.
The Wireless LAN Setting Utility dialog box
appears.
7
Select Simple 1:1 connection then
click OK.The connection starts up.
When a connection confirmation message
appears, proceed as instructed in the
message.
8
When the connection is complete, the
computer screen image is
transmitted.If the transmission does not start, uncheck the Confirm and immediately transmit
screen image checkbox. Notes
•This operation is allowed only when the Transmission mode is set to Ad hoc in the
projector network settings.
•The operation procedure of the projector setting and the computer setting can be
altered without affecting the connection setup, assuming the operation on each side
is complete within 60 seconds.
•Be sure to use Wireless Utility version 4.0.
7
Click on the 
 button.
The selected files image is displayed by the projector and the Control window appears
as well.
8
Play the video file via the Control window.The function of each button and box is as follows:
Current position:Indicates the playing position. Dragging the slider can move the
playing position.
Play:Starts playing the video file.
Freeze:The picture is paused.
Stop:Stops playing the video file.
Volume:Adjusts sound volume.
Mute:Cuts off picture and sound.
Release mute:Restores picture and sound.Notes
•Only one file can be sent at a time. To send another file, repeat steps 
5 and 
7.
•MPEG/AVI/ASF/WMV files can be transmitted.•The update speed of the transmitted file depends on your computers performance and the
surrounding radio environment.•The projector ID is the MAC address of the wireless LAN USB adapter mounted on the
projector.•The audio signals transmitted by a computer become mono.•Playing contents protected by copyright is not suppor ted.■Easy Connect utility
This feature allows users to easily connect the projector to a computer over wireless
networks, without making Network settings via Wireless Utility.
Launch the Wireless Utility software application and click the Tool button 
 to bring
up the Wireless LAN Setting Utility dialog box. Select a desired connection mode in
this dialog box. 
						

							71
Operations
70
2) Modifying the computer settings using the projector settings•Setting on the projector1
Turn the projector power on.
2
Switch the input to Wireless/USB.
3
Press the MENU button twice, then select Easy Connect (USB
memory) in Wireless Utility settings from the Setting display (2) menu
and press the 
 button.
4
When a confirmation window appears, insert the USB memory into
the projector.
5
Click Yes then press the 
 button.
The network settings are saved to the USB memory. When successfully saved, a
message appears.
6
Unplug the USB memory and then insert the supplied wireless LAN
USB adapter.
•Setting on the computer7
Launch the Wireless Utility software
application.
8
Insert the USB memory into the computer.
9
After a confirmation message appears,
make settings.
10
When the setting is complete, the projector name of the connected
projector or the MAC address of the wireless LAN USB adapter is
displayed.
This operation is allowed only when the Transmission mode is set to Ad hoc in the
projector network settings. Be sure to use Wireless Utility version 4.0.
●How to connect USB memory
Set up wireless LAN using a commercial USB memory. See 
p.54
 for available USB
memories.
1) Copying the computer settings to the projector•Setting on the computer1
Insert the USB memory into the USB
terminal slot on the computer.
2
Click the Tool button 
 of the
Wireless Utility to bring up the
Wireless LAN Utility dialog box.
Select Setting USB memory
connection and click OK.
The dialog box for USB memory connection appears.
3
Select [Projector settings] and click OK,
then enter the required setting items and
click OK.The setting information is saved to the USB
memory.
4
Unplug the USB memory from the computer.To unplug the USB memory, follow the instructions in the user s manual supplied
with the USB memory or the computer.
•Setting on the projector
5
Turn the projector power on.
6
Switch the input to Wireless/USB.
7
Insert the USB memory into the projector.A message appears, notifying that the projector settings have been changed.
8
Unplug the USB memory and insert the wireless LAN USB adapter.
The projectors name or the MAC address of the wireless LAN USB
adapter will be displayed on the computers screen.
Using the Wireless Utility (Continued) 
						

							73
Operations
72
2
Click on the Remote
Control button.The Remote Control  window
appears.
As the  Wireless Utility  window is
still displayed, you can operate the
projector via the  Remote Control
window, while using the Wireless
Utility’s functions.
While it is possible to use this function merely to operate the projector, closing the
W ireless Utility  also closes the  Remote Control  window.
3
Select the projector to be operated.In the Remote Control  window, click on the 
 button, and select the
desired projector from the pull-down list. When you make a selection,
the  Remote Control  window displays as shown in  the right figure.
Only one projector can be selected. (It is not possible to operate
m ultiple projectors.)
4
Click on the Remote Control window’s buttons.The function of each button and box is as follows:
Power On :Turns projector power on.
Power Off :Turns projector power off.
Freeze :The picture is paused.
Input  (box) : Click on the 
 button, and select the desired input from the pull-down
list.
Go : Switches to the input selected in the Input box.
Mute : Cuts off picture and sound. Click again to restore picture and sound.
V olume +/– :Adjust sound volume.
Resize Off :Restores the picture to its original size.
Resize +/– :Adjusts the enlargement ratio.
 :M ove screen (up/down/left/right/diagonal)
5
To  quit, click on the 
 button on the Remote Control
window.
P erforming this does not close the  Wireless Utility  window.
To  exit both the  Wireless Utility  and the Remote Control , click on the 
 button on
the  Wireless Utility  window.
Using the Wireless Utility (Continued)●Profile settings
This feature allows the user to save the computer settings.
This feature is useful when you need to change wireless LAN settings according to
where you use the computer.
     
●Detailed setting
This feature allows the user to set details for Easy Connect settings. Make the following
settings as required in this dialog.
• Registering profile automatically
Check this checkbox to automatically register the settings of the Easy Connect as
profile setting data.
• Switching settings automatically at start-up
Check this checkbox to automatically switch to the last used wireless LAN settings
when launching the Wireless Utility.
● WEB browser
Where the computer and the projector are connected over wireless LAN, bring up the
window of Projector Configuration Tool by pressing the  WEB browser button.
 Precautions
• If the page is not displayed correctly, re-select the projector.
• When the network settings are changed, the network connection is disconnected. If
you wish to reconnect, set up the computer again.
Precaution
•The simple 1:1 connection, the USB memor y connection and the profile setting may not
work normally depending on the type of the wireless LAN adapter and the wireless\
 LAN
embedded computer. When such a case arises, use the Wireless Utility menu to make
necessar y network settings manually
.
■ Operating the projector
This function can be used with any projector input.
1
Launch the Wireless Utility software application.The  Screen Image  transmission mode window appears on the computer’s screen. 
						

							75
Operations
74
■Converting files created with Microsoft
® PowerPoint
®
This process provides presentations without using a computer by converting
presentation files created with Microsoft
® PowerPoint
® into JPEG files, storing them on
a USB memory, and displaying them in a slide show.
•To use this conversion mode, Microsoft
® PowerPoint
® must be installed on the
computer.
•Only static images are supported by this process. Animation and audio are not
supported.
Presentation files created with Microsoft
® PowerPoint
® usually
consist of several slides. For this reason, the tool creates a folder
with the name specified in step (5), below, and file for each slide
is created in the folder (starting with slide001.jpg).
(1) In the Conversion Method field, select Converting PPT
file.
(2) In the File settings field, click on the Browse button for PPT
File Name.
The Open dialog box appears.
(3) In the Open dialog box:
(a) Specify the location of the file to be converted; and
(b) Select the PowerPoint
® presentation file to convert,
then click on the Open button.
(4) In the JPEG Conversion Tool window, in the File
settings field, click on the Create button for New
folder name.
The Folder create dialog box appears.
(5) In the Folder create dialog box, in the Folder Name of
document field, specify a folder name of 12 characters or less.
(6) In the Folder create dialog box, click on the Selection button.
The Browse Folders dialog box appears.
(7) In the Browse Folders dialog box:
(a) Specify the location in which to save the folder; and
(b) Click on the OK button.
(8) In the Folder create dialog box:
(a) Click on the Create button.
A confirmation dialog box appears;
(b) Click on the OK button.
(9) (a) In the JPEG Conversion Tool window, click on the
Conversion button.
(b) A confirmation dialog box opens. Click Ye s.
The computer begins to convert the file. When it finishes,
a message appears informing you that a “JPEG file has
been created”.
(1)
(2)
(4)
(9)-(a)(1)
(2)
(4)
(9)-(a)(3)-(b) (3)-(a)
(6)
(8)-(a)(6)
(8)-(a)(5) (5)
(7)-(a)
(7)-(b) (7)-(b)
(8)-(b)
(8)-(b)
(9)-(b)
(9)-(b)
How to use the JPEG Conversion ToolThe JPEG Conversion Tool converts JPEG files not suppor ted by the projector, image files
in other formats, Microsoft
® PowerPoint
® files, and the like into JPEG files suppor ted by the
projector. The JPEG files converted with this tool can be displayed by sending them using the
wireless LAN 
p.65
, or saving them on a USB memor y.
■Launching the JPEG Conversion Tool
The window shown in the figure to the right appears on the
computer screen.
Drag the Image Quality Settings slider to the left or right to set the
image quality of the file after conversion. Lower values create
smaller files, but lower the image quality. (It is not possible to restore
the quality of an image after it has been lowered.)
■Converting an image file
This converts JPEG files using compression formats not supported by the projector,
Windows
® metafiles (wmf), and bitmapped files (bmp) into JPEG
files.
(1) In the Conversion Method field, select Converting image
file. (Status on launch)
(2) In the File settings field, click on the Browse button for
Original Image File Name.
The Open dialog box appears.
(3) In the Open dialog box:
(a) Specify the location of the file to be converted; and
(b) In the Files of Type field, click on the 
 button to select
the file format. A list of files of that format appear in the
Open dialog box.
(4) In the Open dialog box, select the file to convert, then
click on the Open button.
(5) In the JPEG Conversion Tool window, in the File
settings field, select Browse for File name after
conversion. The Save As dialog box appears.
(6) In the Save As dialog box:
(a) Specify the location in which to save the converted
file;
(b) Enter a file name of up to 8 characters in the File
Name field; and
(c) Press the Save button.
(7) (a) In the JPEG Conversion Tool, click on the
Conversion button.
(b) A confirmation dialog box opens. Click Ye s.
The computer converts the file. When it finishes a
message  appears informing you that a “JPEG file has
been created”.
(1)
(2)
(5)
(7)-(a)(1)
(2)
(5)
(7)-(a)
(3)-(b) (3)-(b) (3)-(a)
(4)(6)-(b) (6)-(c) (6)-(a)
(7)-(b) (7)-(b) 
						

							77
Operations
76
Setting up the projector using a Web browser■How to use the “Projector Configuration Tool”
The “Projector Configuration Tool” uses the Web server features of the projector to
set up the projector using a wireless LAN USB adapter.
When using the “Projector Configuration Tool”, set up the wireless LAN connecting
the projector and the computer.
1
See “Checking the projector status” 
p.61
 to display
information on the screen and write down the IP address.
2
Invoke Internet Explorer.Internet Explorer Ver. 6.0 is recommended. Enable the Javascript functions.
* Toshiba does not guarantee the operation for later versions.
3
In the address bar, enter the IP address
“http://xxx.xxx.xxx.xxx/” recorded in step 
1
 above.
The Web browser will then display the following page.
Projector name
Projector ID
MenuNote 1: To prevent access from third parties, the projector is restricted to permit access
only from the computer that has been set up for the TCP/IP to have the same
network address as the projector.
Note 2: If you use a proxy server, do not enable the proxy when accessing the above IP
address.
When the wireless LAN is set to use Ad hoc mode, use the WEB browser function
in the Easy Connect menu of Wireless Utility.
Note
•This function can be enabled using the WEB Browser function in the Easy Connect menu
of Wireless Utility without specifying the URL into the browser s address bar.
■Making a presentation with converted JPEG files
(1) Copy the folder created by the JPEG Conversion Tool, or its contents, onto a USB
memory.
(2) Use the step 
1 in “Playing a slide show from a thumbnail list” 
p.57
 to display a
list of thumbnails.
(3) Follow the instructions in step 
2 in “Playing a slide show from a thumbnail list”
p.57
 to find the thumbnail of the first slide, Slide001.jpg, and move the orange
frame to it. (Select Slide001.jpg)
(4) Press the 
 button on the remote control. An enlarged view of the first slide
appears on the screen. This starts the presentation.
(5) To continue to the next slide, click on the remote control’s 
 button. To go back to
the previous slide, click on the 
 button.
■Creating a screen capture and converting it into a JPEG file
This function saves the current computer screen as a JPEG file.
(1) In the Conversion Method field, select Creating screen
capture.
(2) In the File settings field, click on the Browse button for File
name after conversion.
The Save As dialog box appears.
(3) In the Save As dialog box:
(a) Specify the location in which to save the converted file;
(b) Enter a file name of up to 8 characters in the File Name
field; and
(c) Click on the Save button.
(4) (a) In the JPEG Conversion Tool window, click on the
Conversion button.
(b) A confirmation message appears. Click Ye s.
The computer creates a screen capture, and
converts it into a JPEG file in the specified location.
When it is finished, a message appears to tell you
that a “JPEG file has been created”.Note
•The maximum resolution of JPEG files created with the JPEG Conversion Tool is 1,024 ×
768 pixels.
(1) (1)
(2) (2)
(4)-(a)
(4)-(a)
(3)-(b) (3)-(c) (3)-(a)
(4)-(b) (4)-(b)
How to use the JPEG Conversion Tool (Continued) 
						

							79
Maintenance
78
4
Select items from the menu on the left.Settings
:Make settings for the Wireless/USB input menu.
Status Display:Verify the projector state.
Features:Shows the functions available with the Wireless/USB input
menus.
Top:Returns you to the top page.
TOSHIBA Projector Site
:The browser will display the home page at http://
multimedia.projector-toshiba.com/map.html, providing
projector information. The home page address is subject to
change without notice.
(The Toshiba’s web site can be browsed only when your
computer can access the Internet.)
●Details on major items•SettingsWhen Browser authentication has been set to On, access to the setup page requires the input
of the password.Wireless Utility
:The items displayed on the screen can be set. Entering individual items
and press the Execute button to update their setting. Note, however, that
security items such as “Remote control” and “Browser authentication”
cannot be set.
Slide Show:The items displayed on the screen can be set. Entering individual items
and press the Execute button to update their setting.
Email:The item displayed on the screen can be set. Entering individual items
and press the Execute button to update their setting.
•Status display
Displays some states of the projector.
Projector:Displays the contents of status display in the menu.
Wireless/USB:Displays the contents of status display of the Wireless/USB input.
Maintenance:Describes an error if it occurs, for example, when the lamp has blown.
Note
•Clicking the ? button opens a popup help window.Setting up the projector using a Web browser 
(Continued)
The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.•The lamp may burst with a loud noise due to impact or deterioration, or fail to light at
the expiration of its life.
•How long it takes before the lamp bursts or the life expires may vary greatly by lamp.
Some may burst shortly after first use.
•Burst is likely to happen if the lamp is used after the replacement period has elapsed.
•When the lamp bursts, the broken pieces of glass may get inside the product or be
released outside from the openings for ventilation.
•When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with
glass dust may be released from the openings for ventilation.■
Immediately replace the lamp when a sign appears on the screen.•When the replacement time approaches, a message will appear on the screen.
•The risk of burst will increase if the lamp is continuously used without being replaced.
•Frequently check the used hours and prepare spares when the replacement time
approaches. (Refer to “Status display”. 
p.44
)
■
When the lamp is broken•If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
•In the event of lamp burst, unplug the product from the wall outlet, leave and completely
ventilate the room. Then, thoroughly clean the area around the projector and discard
any edible items placed in that area.
•When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes
or you breathe it.About lampMaintenance