Toshiba Tdp T95 Projector User Manual

							41
Operations
40
■The default setting menuThis menu shows placement status and other settings.
Sets projection mode in accordance with Placement Style.  
Set the time to wait for the power to be turned off after the last 
operation is made with no input signal.
Off  (not turned off)             30 min.
Set whether the input with signals is only selected or not.Sets whether to turn on the power when the  ON/STANDBY button is pressed 
(Manual), or when the power cord is plugged in (Auto).            
Manual             Auto
Sets the lamp power.                                   
Sets the cooling fan speed.
When two or more projectors are used and controlled by the remote 
control respectively, this menu sets the code for the projector and the 
remote control.
[      or      : Enter setting mode]      [           : Select item]      [           : 
Select from  1, 2, 3, 4]      [     :Confirm]      [           :Select  OK to end]  
Press [ Cancel ] to return.
Lock the control panel buttons.
[      or      : Enter setting mode]      [           : Select item]      [           : 
Select  On/Off ]      [     :Confirm]      [           :Select  OK to end]  
Press [ Cancel ] to return.Press       . (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password function
When [ Passwo rd] is [ On], the Password Setting screen is displayed.
Description
Item
Projection
mode
No signal 
power off
A uto input 
search
Po wer on
Lamp power
F an mode
Remote control Key  lock
Reset all
P asswo rd
(Rear 
ceiling)
(Standard)
(Rear) (Ceiling)
On            Off
Standard           High
Yes           No
 Off           On
 
Low           Standard
p.21
p.32
Detailed description
[Auto input search ][On ]: Automatically searches the signals that
can be projected, and switches input
from the connected device that outputs
the video signals each time the  INPUT
b utton is pressed. The input from the
connected device that outputs no video
signals is skipped.
[ Off ]: Displays the  Input select menu.
T oggle with 
 
 buttons and press 
b utton. (The input without signals can be
selected.)
[ Power on ]Note that if [ Power on] is set to [ Auto], then if the power is supplied when restored
after a power outage, the projector will come on.[ Lamp power ]When [Lamp power ] is set to [Low], the screen becomes a little darker, but the
cooling fan noise gets quieter.[ Fan mode ]Setting [Fan mode ] to [High ] increases the cooling fan speed. (The cooling fan
noise gets louder.) Set this option to use the projector, for example, at high altitude
(over 1,500 meters above sea level).
• Do not set Fan mode to [ High] when using the projector at a lower altitude.[Remote control ]Sets a remote control code from 4 types. You can set each code respectively for up
to 4 projectors. The factory setting is [ 1].
To  switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
•Y ou cannot operate the remote control if the codes of the projector and the
remote control do not match.Remote control code setting for remote controlRemove the battery cover and set the same  remote control code switch as the
projector. 
p.16
 (Use a screwdriver with thin tip to set.)
[ Key lock ]Protect from operating errors by locking on the control panel buttons of the
projector. (The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly
operation with the control panel buttons is disabled.
•T o release the key lock, set the [ Key Lock] to [Off] using remote control. Pressing
the [ RETURN ] button on the projector for 10 seconds also sets the [ Key Lock] to
[ Off ]. (In the latter case, the LAMP, TEMP, and FAN indicators light in orange for 3
seconds.)
Computer 1
Y/P
B/PR 1
Computer 2
Y/P
B/PR 2
Video
S-video
Input select





/



 shows whether signal is 
 input or not.
Input select menu
Using the menus (Continued) 
						

							43
Maintenance
42
The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.•The lamp may burst with a loud noise due to impact or deterioration, or fail to light at
the expiration of its life.
•How long it takes before the lamp bursts or the life expires may vary greatly by lamp.
Some may burst shortly after first use.
•Burst is likely to happen if the lamp is used after the replacement period has elapsed.
•When the lamp bursts, the broken pieces of glass may get inside the product or be
released outside from the openings for ventilation.
•When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with
glass dust may be released from the openings for ventilation.■
Immediately replace the lamp when a sign appears on the screen.•When the replacement time approaches, a message will appear on the screen.
•The risk of burst will increase if the lamp is continuously used without being replaced.
•Frequently check the used hours and prepare spares when the replacement time
approaches. (Refer to “Status display”. 
p.42
)
■
When the lamp is broken•If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
•In the event of lamp burst, unplug the product from the wall outlet, leave and completely
ventilate the room. Then, thoroughly clean the area around the projector and discard
any edible items placed in that area.
•When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes
or you breathe it.About lampMaintenance
Using the menus (Continued)■Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item Description
Computer Y/P
B/PR
Video S-video
ProjectorInput Input source name Yes Yes Yes YesMode name RGB input mode 
[Note 1]
Ye s N o N o N o
Resolution Resolution (in dots) Yes No No NoFrequency Sync frequency Yes No No NoSync Sync signal polarity 
[Note 2]
Ye s N o N o N o
Signal format Y/P
B/PR signal format No Yes No No
Video mode Color method of video signal No No Yes YesLamp time Time of lamp use 
[Note 3]
Ye s Ye s Ye s Ye s
Lamp reset count The count for lamp replacement Yes Yes Yes Yes
Total time The total time that this projector is
used.Ye s Ye s Ye s Ye s
Version Firmware version 
[Note 4]
Ye s Ye s Ye s Ye s
Notes
1:The mode of supported RGB signals 
p.50
 is shown.
2:Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3:Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours,  consult
with a dealer about getting replacement for:
TLPLW9 for TDP-T95 or
TLPLW10 for TDP-T100
(sold separately).
4: [Version] shows the version of the projector’s internal control program. This version is referred
to for customer service, etc.
Note•The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again. 
						

							45
Maintenance
44
1
Unplug power cord.
2
Wait until lamp is sufficiently cooled.Wait for at least 1 hour.
3
Remove the lamp cover.Loosen the two screws, raise the lamp cover
with your fingers as shown to remove the lamp
cover. Use care to avoid any damage to nails
and/or tip of your finger(s). If you have any
difficulty in removal, you can use a screwdriver
or any other smaller tool for your convenience.
Lamp cover
21
12
3
4
4
Pull out the lamp.Loosen the three lamp locking screws, pull up the
handle, and remove the lamp.
5
Mount the new lamp.Align the orientation, press down the new lamp
until the bottom is reached, and lock in place using
the three lamp locking screws.
6
Replace the lamp cover.Align the cover, and press it in, then tighten the
screws loosened in step 
3 until the lamp cover is
no longer loose.
7
Reset the lamp timer.See the lamp’s manual for instructions on resetting
the lamp timer.Notes and Precautions
•The Lamp time item in the Status display menu indicates the time of lamp use (as a
rough guide). 
p.42
•It is recommended that the lamp be replaced after 2,000 hours of use. When [Lamp time]
reaches 2,000 hours, the 
 icon and a message will appear. (After 2,000 hours, they will
appear when the power is on at the first time every 100 hours.) This display disappears
when you press the 
 button.
•Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
projector may fail to be powered on or the lamp may fail to come on.
•Always replace the lamp with a new one.
•The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
Used LampsThis projector’s lamps contain trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose of them in accordance with
local regulations.
A lamp is consumable supplies. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime
of the lamp depends on condition of use.) If this happens, replace it with a new one
.
 WARNING
•If the projector is mounted on the ceiling, it is recommended to use your Toshiba dealer-
ship when the lamp has to be exchanged.Uncovering the lamp while the projector is mounted on a ceiling may lead to a danger
of damage from falling pieces of glass if the lamp is broken. Besides, working at high
elevations can also be hazardous. Do not attempt to replace the lamp by yourself.
•When replacement is required, be sure to use:
TLPLW9 for TDP-T95 or
TLPLW10 for TDP-T100
(sold separately). CAUTION
•If you have been using the projector, the lamp will be very hot, and may cause burn injuries
.
Wait for the lamp to cool (for longer than 1 hour) before replacing it.
•
If the lamp should break, please handle with care to avoid injury due to broken pieces and
contact your dealer for repair service.
5
21
Lamp replacement 
						

							47
Others
46
The indicator lights to inform you of internal abnormalities.
No power
⇒Problem with projector
•Unplug the power cord, and contact your dealer.Lamp went out during use, or won’t come on⇒Lamp temperature is high so that it is difficult to turn on, the lifetime of the
lamp has ended or the projector is malfunctioning.
•Unplug the power cord and wait for a short while, then turn the power
back on.
•If a lamp burns out, replace it with a new one.
❈After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.Power went out during use⇒Internal overheating, or the outside temperature is too high.
•Place the projector so that the air intake and exhaust are not blocked.
•Unplug the power cord and wait for a short while, then turn the power
back on.
❈The 
 icon will appear before the power goes out.
❈After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Power went out during use⇒Problem with internal cooling fan.
•Unplug the power cord, and contact your dealer.
❈The 
 icon will appear before the power goes out.
❈After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Power went out during use, or power won’t come on⇒The lamp cover is not properly attached.
•Unplug the power cord, and reattach the lamp cover. 
p.44
❈After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
Power went out during use⇒Problem inside the projector.
•Unplug the power cord and wait for a short while, then turn the power
back on.
•If the above action will not clear the problem, unplug  the power cord,
and contact your dealer.
❈The 
 icon will appear before the power goes out.
❈After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.
(Off)
Or (Orange lit)
Or (Orange lit
or flashing)
(Red lit)
Trouble indications(Red lit)
(Green lit)
(Red lit or flashing)
(Red lit)(Red lit)(Red lit)
(Red lit)(Green
flashing)
(Orange
flashing)
(Red lit)
 WARNING
•Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership
.
Attempting to clean/replace the lamp at a high site by yourself may cause you to fall
down, thus resulting in injury.
■Lens cleaning•Clean the lens with a commercially available blower and/or
lens cleaner.
•The lens is easily scratched, so do not rub it with hard objects,
or strike it.■Main unit cleaning•Clean the main unit after unplugging the power cord.
•Wipe dirt off the main unit gently with a soft cloth.
•Do not wipe the main unit with a damp cloth. Doing
so may allow water to get inside, resulting in an
electric shock or failure.
•Do not use benzene, thinner and the like as they may
deform or discolor the unit or damage the paint
surface.
•When using a chemically treated cloth, follow the
precautions included with the cloth.Lens and main unit cleaning 
						

							49
Others
48
Specifications■List of general specifications
Item Specification
Consumption Power TDP-T95: 310 W
TDP-T100: 380 W
Weight TDP-T95: 2.9 kg
TDP-T100: 3.0 kg
External Dimensions 300 × 99  × 218 mm (W  × H  × D)
(including protruding parts)Cabinet material PC+ABS resin and ABS resinConditions for usage
 environment
Temp: 5 °C to 35 °C; relative humidity: 30% to 70%
Display pixels
1 chip DMD™
Picture elements
786,432 pixels (1024H  × 768V)
Lens Zoom lens      F=2.07-2.64   f=20.5-32.8 mmLamp TDP-T95: High-pressure mercury lamp (210 W)
TDP-T100: High-pressure mercury lamp (275 W)
Projection screen size 30-300 inchesProjection distance 1.07-11.09 mSpeaker 1W (Mono)
COMPUTER 1
Mini D sub 15 pin  RGB / Y/P
B/PR (dual use)
IN terminalCOMPUTER 2
Mini D sub 15 pin  RGB / Y/P
B/PR (dual use)
IN terminalMONITOR terminal Mini D sub 15 pin  RGB / Y/P
B/PR (dual use)
S-VIDEO terminal Mini DIN 4 pinA UDIO (L/R) terminal RCA Pin Jack  × 2, 1.5 V (rms), 22 k Ω or moreVIDEO terminal RCA Pin Jack, 1 V (p-p), 75 ΩAUDIO (L/R) terminal RCA Pin Jack  × 2, 1.5 V (rms), 22 k Ω or moreAUDIO IN terminal 3.5mm dia. stereo mini-jack, 1.5 V (rms), 22 k
Ω or more
AUDIO OUT terminal 3.5mm dia. stereo mini-jackCONTROL terminal
Mini DIN 8 pin (RS-232C)
Notes
• This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added
in the future.■ Separately sold product
Replacement Lamp for TDP-T95 Model TLPLW9
Replacement Lamp for TDP-T100 Model TLPLW10Connection terminal
If you think something is wrong, check the followings before contacting customer service.
Please see “ Trouble indications ” 
p.47
 as well.
If  This Happens Check
No powerPower goes out
during useNo pictureNo audioPicture not
displayed
correctlyPicture blurred
Part of picture
out of focusImage is darkColors too light
Bad shadingControl panel
key doesn’t workRemote control
doesn’t workBefore calling service personnel
• Is the power cord plugged in? Is it connected to the projector?
• Is the outer lamp cover attached properly? 
p.44
•Is the ambient temperature high? 
p.47
•Is the air intake or air exhaust blocked? 
p.47
•Is the projector turned on? (When [Auto input search] is [Off]) 
p.40
•Is the mute function on? 
p.30
•Is the brightness setting minimized? 
p.35
•Are the connections set up correctly? 
p.22
•Are all the connected devices functioning properly?
• Is the mute function on? 
p.30
•Is the volume setting minimized? 
p.27
•Are the connections set up correctly? 
p.22
•Are all the connected devices functioning properly?
• Is the input signal supported by the projector? 
p.50
, p.51
•Is there something generating an abnormal video signal, for
instance the video tape?
• Is the lens dirty? 
p.46
•Is the lens focus adjusted optimally? 
p.27
•Is the projection distance within the projector’s supported range? 
p.21
•Is the projector’s screen placement angle tilted too far?  
p.21
•Are the sharpness or sampling phase adjustments off? 
p.35
•Are the brightness or contrast adjustments off? 
p.35
•Is the lamp nearing the end of its service life? 
p.42
•Are the color, R-level, G-level, or B-level adjustments off? 
p.35
•Is the screen dirty?
• Is the blackboard mode set properly? 
p.37
•Is the lamp nearing the end of its service life? 
p.42
•Is the key lock function on? 
p.41
•Is the remote control ON/OFF switch set off? 
p.19
•Is the remote control code identical with the projectors code? 
p.41
•Are the remote control’s batteries drained?
• Are the batteries inserted into the remote control correctly? 
p.19
•Is the remote control being used within the effective range? 
p.19
•Are there any obstructions between the remote control and projector?•Are there any fluorescent or other bright lights shining at the
projector’s infrared remote sensor? 
						

							51
Others
50
■List of supported signals (Y/P
B/P
R signals)
Signal format fh(kHz) fv(Hz)
480i(525i)@60Hz15.73 59.94
480p(525p)@60Hz31.47 59.94
576i(625i)@50Hz15.63 50.00
576p(625p)@50Hz31.25 50.00
720p(750p)@60Hz45.00 60.00
720p(750p)@50Hz37.50 50.00
1080i(1125i)@60Hz33.75 60.00
1080i(1125i)@50Hz28.13 50.00
■List of supported signals (Video, S-Video signals)
Video mode fh(kHz) fv(Hz) fsc(MHz)
NTSC 15.73 60 3.58
PAL15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41
PAL-M 15.73 60 3.58
PAL-N 15.63 50 3.58
PAL-60 15.73 60 4.43
NTSC4.43 15.73 60 4.43
■Pin assignment of COMPUTER 1 IN, COMPUTER 2 IN &
MONITOR terminals
11 156 1 5
10
Input Signal
•RGB input
RGB signals: 0.7V (p-p) 75 ΩHorizontal sync signal
:TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)
•Y/P
B/PR input
Y signal: 1.0V (p-p) 75 Ω
P
B/PR signals: 0.7V (p-p) 75 Ω Mini D sub 15 Pin connector
Pin Pin descriptionNo. During RGB input During Y/P
B/PR input
1Video signal (R) Color difference signal (P
R)
2Video signal (G) Luminance signal (Y)3Video signal (B) Color difference signal (P
B)
4GND∗5GND∗6GND (R) GND (P
R)
7GND (G) GND (Y)8GND (B) GND (P
B)
9N.C∗10 GND∗11 GND∗12 N.C∗13 Horizontal sync signal∗14 Vertical sync signal∗
15 N.C∗∗ Do not connect anything.
■List of supported signals (RGB signals)This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
Resolution
720 x 400
640 x 480
800 x 600
832 x 624
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
1400 x 1050
1600 x 1200Mode
720x400_85
VGA_60
VGA_72
VGA_75
VGA_85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85
MAC16
XGA_60
XGA_70
XGA_75
XGA_85
MAC19
SXGA1_75
QuadVGA_60
QuadVGA_85
SXGA3_60
SXGA3_75
SXGA3_85
SXGA+
UXGA_60
UXGA_65
UXGA_70
UXGA_75
UXGA_85Refresh rate
(Hz)
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
74.550
60.004
70.069
75.029
84.997
74.700
75.000
60.000
85.002
60.020
75.025
85.024
59.978
60.000
65.000
70.000
75.000
85.000H-frequency
(kHz)
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
68.667
60.134
67.500
60.000
85.938
63.981
79.976
91.146
65.317
75.000
81.250
87.500
93.750
106.250Clock
(MHz)
35.500
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
57.283
65.000
75.000
78.750
94.500
79.857
108.000
108.000
148.500
108.000
135.000
157.500
121.750
162.000
175.500
189.000
202.500
229.500Note
•Signals whose resolution exceeds the native resolution (1024 × 768 pixels) will be
compressed. For this reason, some information may be lost, or image quality may be
affected.Specifications (Continued) 
						

							52
Specifications (Continued)■CONTROL terminal●Pin assignment
7
6
8
5
43
21
Signal Name
RXD
CTS
DSR
GND
RTS
N.C
TXD
GND Pin No.
1
2
3
4
5
6
7
8Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
Signal ground
Mini DIN 8 pin connector
●Interface format
1Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:  1 bit
2Communication format STX (02h)  Command (3Byte)  ETX (03h)
Only 1 command valid per communication.
3Data format For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
4Replies Acknowledge ACK (06h)  CR (0Dh)  Data ...  Normally ended
ACK (06h)  ESC (1Bh) ...  Aborted
No acknowledge NAK (15h)
If commands are to be sent consecutively, wait for the response from the projector
before sending the next command.
●Main Commands
Item Command
Power onPONPower offPOFIcon display onMO0Icon display offMO1Auto setting (RGB input)PATStatus display onDON
Status display offDOFNote
•Contact your dealer for control cable and other commands.