Toshiba Tdp T350 Projector User Manual

21
20
Preparations
■Operating the remote
controlTurn on the ON/OFF switch of the
remote control.
Point toward the projector’s
infrared remote sensor, and press a
button on the remote control.•Operating the projector from the front
Approx. 15°Approx. 5m
•Operating the projector from the rear
Approx. 15°
Approx. 5m
■Loading dry-cell batteries
into the remote controlqRemove the battery cover.wInsert the dry-cell batteries.
Be sure to align the plus and minus
ends of the batteries properly.Two batteries...

23
22
Preparations
Placement StylesAs shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the [ Projection mode] in the
Default setting  menu 
p.44
, in accordance with your needs.
Placement
 W ARNING
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus
resulting in injury.
• If you...

25 24
Preparations
Before connection•Read the owner’s manual of the device you are connecting to the projector.
•Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal 
p.56
, etc.
•Turn off the power of both devices before connecting.
•The figures are sample connections.
Connecting with computers
Notes
•Signals are output from MONITOR OUT terminal even in standby mode.
   From AUDIO OUT terminal, no audio signal is output.
•Moving...

27
Operations
26
•The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed 
p.28
.
•Y ou can disable the beep sound in the  Display setting menu 
p.41
.
• When [ Key lock] is [On], the operation buttons of the projector do not work 
p.44
.
• When [ Password ] is [On], the start-up screen is displayed after the Password entry
screen disappears 
p.44
.
■ Turning the power off1
Press the ON/STANDBY button.A message appears on the screen,...

29
Operations
28
5
Projector placement angle adjustmentsThe placement angle and the height of the projected image can be adjuste\
d by the foot
adjuster.qLift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
w To fine adjust the angle, twist the
f oot adjuster.
e To adjust the horizontal angle, use
the tilt adjuster.To  stow the foot adjuster, hold up the projector
while pressing the foot...

31
Operations
30
Adjusting vertical distortion [Auto]2
Press the 
 button.
The keystone distortion is automatically corrected. The 
 icon appears during this
correction.
When adjustment is finished, the  Keystone  menu appears again. For fine adjust-
ment, select [ V-keystone ] by the 
 button and adjust image manually by the 
 buttons.
Adjusting vertical distortion [Manual]1
Press the KEYSTONE button.
2
Select [V-keystone] by the 
 b utton.
3
Use the 
 
 buttons for keystone adjustment.
Adjusting...

33
Operations
32
■Changing picture mode
The projected image mode can be selected.
Press the remote control’s PICTURE button.Pressing the button switches Bright/Standard/True color in turn.Note•[Picture mode] of the Image adjustment menu has the same
function 
p.39
.
■Changing screen size
The screen size for the projected image can be changed.
Press the remote control’s SCREEN SIZE button.Pressing the button switches Full/Thru/Wide in turn.Notes•Thru display is available for computer-input images....

35
Operations
34
■Displaying two screens (SPLIT function)
This function displays two screens at a time.
Press the remote control’s SPLIT button.The projected image moves to the left (main
screen), and a new image is displayed to
the right (sub screen). To switch the sub and
main screens, press the remote controls
SWAP button.
To hide the sub screen, press the SPLIT
button again.Notes•Sound of the main screen is output.
•Size of the screens and input source of the sub screen can be changed in the
SPLIT...

37
Operations
36
How to set password (from [Off] to [On])
1
Select [Password] in the Default setting menu and press the 
 or 
button.The password setting confirmation screen is displayed. ([OK] or [Cancel])
2
Select [OK] and press the 
 button.
The password entry screen is displayed.
3
Enter a four-digit number for the password using numeric keys of the
remote control.The input number appears as [****].
4
Re-enter the same password for confirmation.When the password is confirmed, the setting is complete...

39
Operations
38
■The image adjustment menuUse this menu to set or adjust image-related items. Items that can be set or adjusted are
marked with “Yes”, and those that cannot are marked with “No”. (When an item is masked,
it indicates that you cannot select for the current input.)
Digital (DVI)
Analog (D-SUB)(BNC)
Item 
  
Description
RGB Y/P
B/PRRGB Y/P
B/PRVideo
S-video
 
ContrastAdjust the image contrast. Yes Yes Yes Yes Yes Yes
Lower
Higher
BrightnessAdjust the brightness of the image. Yes Yes Yes Yes...