Toshiba Tdp T250u Projector User Manual

20
21
Operations
■Operating the remote
controlTurn on the ON/OFF switch of the
remote control.
Point toward the projector’s
infrared remote sensor, and press a
button on the remote control.•Operating the projector from the front
Approx. 15°Approx. 5m
•Operating the projector from the rear
Approx. 15°
Approx. 5m
■Loading dry-cell batteries
into the remote controlqRemove the battery cover.wInsert the dry-cell batteries.
Be sure to align the plus and minus
ends of the batteries properly.Two batteries (LR03,...

23 22
Preparations
Placement StylesAs shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the Projection mode in the
default setting menu 
p.42
, in accordance with your needs.
Placement
 WARNING
•Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus
resulting in injury.
•If you wish to...

25 24
Preparations
Before connection•Read the owner’s manual of the device you are connecting to the projector.
•Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal 
p.53
, etc.
•Turn off the power of both devices before connecting.
•The figures are sample connections.
Connecting with computers
Note
Moving pictures played back on computers using DVD software may appear unnatural if it
is projected with this projector, but it is not a...

27
Operations
26
Notes
•The start-up screen will disappear after a moment. You can dismiss the star t-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu 
p.40
.
•The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed 
p.28
.
•You can disable the beep sound in the Default setting menu 
p.42
.
■Turning the power off1
Press the ON/STANDBY button.A message...

29
Operations
28
5
Projector placement angle adjustmentsThe placement angle and the height of the projected image can be adjusted by the foot
adjuster.qLift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
wTo fine adjust the angle, twist the
foot adjuster.
eTo adjust the horizontal angle, use
the tilt adjuster.To stow the foot adjuster, hold up the projector
while pressing the foot...

31
Operations
30
Adjusting vertical distortion [auto]2
Press the 
 button.
The keystone distortion is automatically corrected. The 
 icon appears during this
correction.
When adjustment is finished, the Distortion adjust menu appears again. For fine
adjustment, select [V-keystone adjust] by the 
 button and adjust image manually
by the 
 
 buttons.
Adjusting vertical distortion [manual]1
Press the KEYSTONE button.
2
Select [V-keystone adjust] by the 
 button.
3
Use the 
 
 buttons for keystone...

33
Operations
32
■Changing picture mode
The projected image mode can be selected.
Press the remote control’s PICTURE button.Pressing the button switches Bright/Standard/True color in turn.Note•[Picture mode] of the Image adjustment menu has the same
function 
p.38
.
■Changing screen size
The screen size for the projected image can be changed.
Press the remote control’s SCREEN SIZE button.Pressing the button switches Full/Thru/Wide in turn.Notes•Thru display is available for computer-input images....

35
Operations
34
■Displaying two screens (SPLIT function)
This function displays two screens at a time.
Press the remote control’s SPLIT
button.The projected image moves to the left (main
screen), and a new image is displayed to
the right (sub screen). To switch the sub and
main screens, press the remote controls
SWAP button.
To hide the sub screen, press the SPLIT
button again.Notes•Sound of the main screen is output.
•Size of the screens and input source of the sub screen can be changed in the
SPLIT...

37
Operations
36
How to set password (from [Off] to [On])
1
Select [Password] in the Default setting menu and press the 
 or 
button.The password setting confirmation screen is displayed. ([OK] or [Cancel])
2
Select [OK] and press the 
 button.
The password entry screen is displayed.
3
Enter a four-digit number for the password using numeric keys of the
remote control.The input number appears as [****].
4
Re-enter the same password for confirmation.When the password is confirmed, the setting is complete...

39
Operations
38
■The image adjustment menuUse this menu to set or adjust image-related items. Items that can be set or adjusted are
marked with “Yes”, and those that cannot are marked with “No”. (When an item is masked,
it indicates that you cannot select for the current input.)
Digital (DVI)
Analog (D-SUB)(BNC)
Item 
  
Description
RGB Y/P
B/PRRGB Y/P
B/PRVideo
S-video
 
ContrastAdjust the image contrast. Yes Yes Yes Yes Yes Yes
Lower
Higher
BrightnessAdjust the brightness of the image. Yes Yes Yes Yes...