Toshiba Tdp T100 Projector User Manual

41
Operations
40
■The default setting menuThis menu shows placement status and other settings.
Sets projection mode in accordance with Placement Style.  
Set the time to wait for the power to be turned off after the last 
operation is made with no input signal.
Off  (not turned off)             30 min.
Set whether the input with signals is only selected or not.Sets whether to turn on the power when the  ON/STANDBY button is pressed 
(Manual), or when the power cord is plugged in (Auto)....

43
Maintenance
42
The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.•The lamp may burst with a loud noise due to impact or deterioration, or fail to light at
the expiration of its life.
•How long it takes before the lamp bursts or the life expires may vary greatly by lamp.
Some may burst shortly after first use.
•Burst is likely to happen if the lamp is used after...

45
Maintenance
44
1
Unplug power cord.
2
Wait until lamp is sufficiently cooled.Wait for at least 1 hour.
3
Remove the lamp cover.Loosen the two screws, raise the lamp cover
with your fingers as shown to remove the lamp
cover. Use care to avoid any damage to nails
and/or tip of your finger(s). If you have any
difficulty in removal, you can use a screwdriver
or any other smaller tool for your convenience.
Lamp cover
21
12
3
4
4
Pull out the lamp.Loosen the three lamp locking screws, pull up the
handle,...

47
Others
46
The indicator lights to inform you of internal abnormalities.
No power
⇒Problem with projector
•Unplug the power cord, and contact your dealer.Lamp went out during use, or won’t come on⇒Lamp temperature is high so that it is difficult to turn on, the lifetime of the
lamp has ended or the projector is malfunctioning.
•Unplug the power cord and wait for a short while, then turn the power
back on.
•If a lamp burns out, replace it with a new one.
❈After approx. one minute of abnormal display,...

49
Others
48
Specifications■List of general specifications
Item Specification
Consumption Power TDP-T95: 310 W
TDP-T100: 380 W
Weight TDP-T95: 2.9 kg
TDP-T100: 3.0 kg
External Dimensions 300 × 99  × 218 mm (W  × H  × D)
(including protruding parts)Cabinet material PC+ABS resin and ABS resinConditions for usage
 environment
Temp: 5 °C to 35 °C; relative humidity: 30% to 70%
Display pixels
1 chip DMD™
Picture elements
786,432 pixels (1024H  × 768V)
Lens Zoom lens      F=2.07-2.64   f=20.5-32.8 mmLamp...

51
Others
50
■List of supported signals (Y/P
B/P
R signals)
Signal format fh(kHz) fv(Hz)
480i(525i)@60Hz15.73 59.94
480p(525p)@60Hz31.47 59.94
576i(625i)@50Hz15.63 50.00
576p(625p)@50Hz31.25 50.00
720p(750p)@60Hz45.00 60.00
720p(750p)@50Hz37.50 50.00
1080i(1125i)@60Hz33.75 60.00
1080i(1125i)@50Hz28.13 50.00
■List of supported signals (Video, S-Video signals)
Video mode fh(kHz) fv(Hz) fsc(MHz)
NTSC 15.73 60 3.58
PAL15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41
PAL-M 15.73 60 3.58
PAL-N 15.63 50 3.58
PAL-60...

52
Specifications (Continued)■CONTROL terminal●Pin assignment
7
6
8
5
43
21
Signal Name
RXD
CTS
DSR
GND
RTS
N.C
TXD
GND Pin No.
1
2
3
4
5
6
7
8Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
Signal ground
Mini DIN 8 pin connector
●Interface format
1Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:  1 bit
2Communication format STX (02h)  Command (3Byte)  ETX (03h)
Only 1 command valid per...