Toshiba Satellite Pro Te2000 Manual

D-3
APPENDIX
 D
S4 Response formatting character (user defined)
This register determines the ASCII value used as the line feed
character. The modem uses a line feed character in command mode
when it responds to the computer.
Range: 0-127, ASCII decimal
Default: 10 (line feed)
Units: ASCII
S5 Command line editing character (user defined)
This register sets the character recognized as a backspace and pertains
to asynchronous only. The modem will not recognize the backspace
character if it is set to a value...

Users Manual
D-4
APPENDIX
 D
S7 Connection completion time-out
This register sets the time, in seconds, that the modem must wait
before hanging up because carrier is not detected. The timer is started
when the modem finishes dialing (originate), or goes off-hook
(answer). In originate mode, the timer is reset upon detection of an
answer tone if allowed by county restriction. The timer also specifies
the wait for silence time for the @ dial modifier in seconds. S7 is not
associated with the W dial...

D-5
APPENDIX
 D
S37 Dial line rate
S37 = 0 (default) maximum modem speed
S37 = 1 reserved
S37 = 2 1200/75 bps
S37 = 3 300 bps
S37 = 4 reserved
S37 = 5 1200 bps
S37 = 6 2400 bps
S37 = 7 4800 bps
S37 = 8 7200 bps
S37 = 9 9600 bps
S37 = 10 12000 bps
S37 = 11 14400 bps
S37 = 12 16800 bps
S37 = 13 19200 bps
S37 = 14 21600 bps
S37 = 15 24000 bps
S37 = 16 26400 bps
S37 = 17 28800 bps
S37 = 18 31200 bps
S37 = 19 33600 bps
Appendix D 

Users Manual
D-6
APPENDIX
 D
AT command set result codes
The following table shows the result codes.
The result code summary
Result Code Numeric Description
OK 0 Command executed
CONNECT 1 Modem connected to line
RING 2 A ring signal has been detected
NO CARRIER 3 Modem lost carrier signal, or does
not detect carrier signal, or does
not detect answer tone
ERROR 4 Invalid command
CONNECT 1200 EC*
15 Connection at 1200 bps
NO DIAL TONE 6 No dial tone detected
BUSY 7 Busy signal detected
NO ANSWER 8 No...

D-7
APPENDIX
 D
Result Code Numeric Description
DELAYED*
288 Delay is in effect for the dialed
number
BLACKLISTED*
289 Dialed number is blacklisted
BLACKLIST FULL*
290 Blacklist is full
*1:EC only appears when the Extended Result Codes configuration option is
enabled. EC is replaced by one of the following symbols, depending upon
the error control method used:
V.42bis - V.42 error control and V.42bis data compression.
V.42 - V.42 error control only.
MNP 5 - MNP class 4 error control and MNP class 5 data...

Users Manual
D-8
APPENDIX
 D 

E-1
APPENDIX
 E
Appendix E
V.90
The TOSHIBA internal modem uses V.90 technology. The modem is capable of
downstream speeds of 56Kbps (kilobits per second) when connected to an Internet
service provider that supports V.90. As with any modem, the actual throughput
(speed of data transfer) depends on analog telephone line conditions, which can
vary considerably. Therefore, many users will experience throughput in the range of
32-44Kbps under normal telephone line conditions. Upstream data flows at the V.
34...

Users Manual
E-2
APPENDIX
 E
Table E-1 Result codes for a V.90 connection
No. Result code Description
70 CONNECT 32000 EC* Connection at 32000 bits/s
72 CONNECT 36000 EC* Connection at 36000 bits/s
74 CONNECT 40000 EC* Connection at 40000 bits/s
76 CONNECT 44000 EC* Connection at 44000 bits/s
78 CONNECT 48000 EC* Connection at 48000 bits/s
80 CONNECT 52000 EC* Connection at 52000 bits/s
82 CONNECT 56000 EC* Connection at 56000 bits/s
100 CONNECT 28000 EC* Connection at 28000 bits/s
101 CONNECT 29333 EC*...

E-3
APPENDIX
 E
AT Command
-V90=* V.90 Dial Line Rate
-V90 sets the maximum V.90 downstream that the modem attempts to
connect.
-V90=0 V.90 disabled
-V90=1 V.90 enabled: automatic speed selection - maximum modem speed
(default)
Appendix E 

Users Manual
E-4
APPENDIX
 E