Toshiba Satellite Pro Te2000 Manual

8-4
User’s Manual
OPTIONAL
 D
EVICES
Figure 8-3  Removing the PC card
Memory expansion
You can install additional memory in the computer’s memory module to increase
the amount of RAM.
128,256  or 512MB memory modules can be installed in the two memory slots for a
maximum of 1GB system memory.
CAUTION: Only memory modules with the following parts numbers can
be installed:
PA3085U-1M12: 128 MB
PA3086U-1M25: 256MB
PA3108U-1M51: 512 MB
CAUTION: Windows 98 does not support more then 512MB of memory
and will...

 8-5
OPTIONAL
 D
EVICES
2. If you install a memory module that is not compatible
with the computer, a beep will sound when you turn on
the power. If the module is installed in slot A, there will
be a long beep followed by a short beep. If the module
is in slot B, there will be a long beep followed by two
short beeps. In this case shut down the power and
remove the incompatible module.
2. Remove all cables connected to the computer.
3. Turn the computer upside down and remove the battery pack (refer to...

8-6
User’s Manual
OPTIONAL
 D
EVICES
Figure 8-7  Inserting the memory module
8. Seat the cover and secure it with two screws.
9. When you turn the computer on, it should automatically recognize the total
memory capacity. Use the HW Setup program to verify that the added
memory is recognized. If it is not recognized, check the module’s connection.
Removing memory module
To remove the memory module, make sure the computer is in boot mode then:
1. Turn the computer off and remove all cables connected to the...

 8-7
OPTIONAL
 D
EVICES
Slim Select Bay 2nd battery pack
Figure 8-8  Removing the memory module
7. Seat the cover and secure it with two screws.
CAUTION: If only one memory module is installed, use slot A. Do not try
to operate the computer with a module installed in slot B only.
Additional battery pack
You can increase the portability of the computer with additional battery packs
(PA3128*). If you’re away from an AC power source, you can replace a low battery
with a fully charged one. See Chapter 6,...

8-8
User’s Manual
OPTIONAL
 D
EVICES
Installing
To install the secondary battery pack in the adaptor, follow the steps below.
1. Fit the side of the secondary battery pack opposite the connector into the
adaptor.
2. Lay the battery into the adaptor. The latch should close automatically to secure
the secondary battery pack.
Figure 8-9  Installing the secondary battery pack in the adaptor
Removing
To remove the secondary battery from the adaptor, follow the steps below.
1. Slide the latch in the direction...

 8-9
OPTIONAL
 D
EVICES
Additional AC adaptor
If you frequently transport the computer between different sites such as your home
and office, purchasing an AC adaptor for each location will reduce the weight and
bulk of your carrying load: PA3083*.
Battery charger
The battery charger (PA3091*) provides a convenient way to charge battery packs
without requiring the use of your computer. The battery charger holds up to two
Lithium-ion battery packs, which it charges one after the other in succession....

8-10
User’s Manual
OPTIONAL
 D
EVICES
2. Insert the HDD and push forward to ensure a firm connection.
Figure 8-12  Installing the HDD
3. Close the lid and slide the lock to the lock position.
Figure 8-13  Closing the lid
For details on installing the Slim Select Bay HDD adaptor in the Slim Select Bay,
refer to Chapter 4, Operating Basics. 

 8-11
OPTIONAL
 D
EVICES
USB diskette drive
The 3 1/2 external diskette drive module can be connected to the USB port. For
details on connecting the 3 1/2 external diskette drive module, refer to Chapter 4,
Operating Basics.
Advanced Port Replicator
In addition to the ports available on the computer, the Port Replicator provides,
audio line-out jack, line-in jack and separate ports for PS/2 mouse and PS/2
keyboard. The Port Replicator connects directly to the docking interface on the
bottom of the...

8-12
User’s Manual
OPTIONAL
 D
EVICES
Parallel printer
You can connect any standard Centronics-compatible parallel printer to your
computer. All you need is an IBM PC™ parallel printer cable. Your dealer can
supply one or you can purchase one at most computer stores.
The cable’s connectors are designed so that it is impossible for you to connect them
incorrectly. You can also connect a parallel printer to an optional Advanced Port
Replicator. To connect a printer, follow these steps:
1. Turn off the...

 8-13
OPTIONAL
 D
EVICES
External monitor
External monitor
An external analog monitor can be connected to the external monitor port on the
computer, Port Replicator. The computer supports VGA and Super VGA video
modes. To connect a monitor, follow the steps below.
CAUTION: If an external monitor is connected to the computer, do not
connect the Port Replicator. First disconnect the external monitor from
the computer then connect the Port Replicator and use its external
monitor port.
NOTE: The Resume...