Toshiba Satellite Pro Te2000 Manual

Users Manual
OPERATING
 B
ASICS
4-4
Installing a module
Install the Slim Select Bay HDD adaptor as described below.
1. Insert the Slim Select Bay HDD adaptor in the computer as shown below and
press until the ejector clicks.
2. If  you want to lock the Slim Select Bay module, set the screw of the Slim
Select Bay lock in the back hole.
Figure 4-4  Installing the Slim Select Bay HDD adaptor
Using optical media drives
The text and illustrations in this section refer primarily to the DVD-ROM drive.
However,...

OPERATING
 B
ASICS
 4-5
Using optical media drives
CD-R/RW drive
Read
CD, CD-R24-speed (maximum)
CD-RW14-speed (maximum)
Write
CD-R8-speed (maximum)
CD-RW8-speed (maximum)
CD-RW/DVD-ROM drive
Read
CD24-speed (maximum)
DVD8-speed (maximum)
Write
CD-R8-speed (maximum)
CD-RW8-speed (maximum)
Loading CDs
To load CDs, follow the steps below and refer to figures 4-5 to 4-9.
1. Turn on the power.
2. a. Press the eject button to open the drawer slightly.
Figure 4-5  Pressing the eject button 

Users Manual
OPERATING
 B
ASICS
4-6
b. Pressing the eject button will not open the drawer when the computer’s
power is off. If the power is off, you can open the drawer by inserting a
slender object (about 1.5 cm) such as a straightened paper clip into the
eject hole just to the right of the eject button.
Figure 4-6  Manual release with the eject hole
3. Grasp the drawer gently and pull until it is fully opened.
Figure 4-7  Pulling the drawer open 

OPERATING
 B
ASICS
 4-7
Using optical media drives
4. Lay the CD, label side up, in the drawer.
NOTE: When the drawer is fully opened, the edge of the computer will
extend slightly over the CD tray. Therefore, you will need to turn the CD
at an angle when you place it in the tray. After seating the CD, however,
make sure it lies flat, as shown in figure 4-8.
CAUTIONS: 1. Do not touch the laser lens. Doing so could cause
misalignment.
2. Be careful to keep foreign matter from entering the
drive. Check the...

Users Manual
OPERATING
 B
ASICS
4-8
6. Push the center of the drawer to close it. Press gently until it locks into place.
CAUTION: If the CD is not seated properly when the drawer is closed,
the CD might be damaged. Also, the drawer might not open fully when
you press the eject button.
Figure 4-9  Closing the drawer
Removing CDs
To remove the CD, follow the steps below and refer to figure 4-10.
CAUTION: Do not press the eject button while the computer is accessing
the CD-ROM drive. Wait for the eject...

OPERATING
 B
ASICS
 4-9
Using optical media drives
2. There are indentations on the sides of the drawer to let you grasp the CD. Hold
it gently and lift it out.
NOTE: When the drawer is fully opened, the edge of the computer will
extend slightly over the CD tray. Therefore, you will need to turn the CD
at an angle when you remove it.
Figure 4-10  Removing a CD
3. Push the center of the drawer to close it. Press gently until it locks into place.
CD/DVDs care
Handle your media with care. The following...

Users Manual
OPERATING
 B
ASICS
4-10
5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy
objects on your CD/DVDs.
6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth.
Wipe from the center out, do not wipe in a circular direction around the CD/
DVD. If necessary, use a cloth dampened in water or a neutral cleaner. Do not
use benzine, thinner or similar cleaner.
Using 3 1/2 external diskette drive
An optional 3 1/2 external diskette drive module connects to...

OPERATING
 B
ASICS
 4-11
Using 3 1/2 external diskette drive
NOTES:1. The external diskette drive should be placed on a flat,
horizontal surface when in use. Do not set the drive on an
incline greater than 20
o while it is operating.
2. Do not set anything on top of the diskette drive.
3. If you need to boot the computer from the diskette drive or if
you use an OS that does not support USB, you must set the
USB-FDD Legacy Emulation feature in HW Setup to
Enabled. Refer to the USB section in Chapter 7....

Users Manual
OPERATING
 B
ASICS
4-12
Disconnecting 3 1/2 diskette drive
When you have finished using the diskette drive, follow the procedures below to
disconnect it:
1. Wait for the indicator light to go out to make sure all diskette activity has
stopped.
CAUTION: If you disconnect the diskette drive or turn off the power
while the computer is accessing the drive you may lose data or damage
the diskette or the drive.
2. Pull the diskette drive connector out of the USB port.
Diskette care
Handle your...

OPERATING
 B
ASICS
 4-13
Wireless communications
Wireless LAN
The wireless LAN is compatible with other LAN systems based on Direct Sequence
Spread Spectrum radio technology that complies with IEEE 802.11 wireless LAN
standard (Revision B). It supports the following features:
❑Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2
and 1 Mbit/s.
❑Frequency Channel Selection (2.4 GHz)
❑Roaming over multiple channels
❑Card Power Management
❑Wired Equivalent Privacy (WEP) data...