Toshiba Projector Tlp Xc3000a User Manual

21
20
Preparations
Operating a computer using the remote control
The remote control may fail to operate
if the mouse remote control receiver is
exposed to bright sunlight or
fluorescent lighting.
In such a case, change position or
direction of the mouse remote control
receiver and retry.
Mouse control
Remote Control Front Remote Control Rear
PAGE –PAGE +
R-CLICK L-CLICK
■
Operating the remote
controlTurn on the ON/OFF switch of the
remote control.
Point toward the projector’s
infrared remote sensor, and...

23
22
Preparations
p.59
Video recorder,
D VD player, etc.
To  audio output
White (L)/Red (R)
S-video cable
(not supplied)
To S-video output
Before connection•Read the owner’s manual of the device you are connecting to the projector.
• Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal 
p.57
, etc.
•T urn off the power of both devices before connecting.
• The figure is a sample connection. This does not mean that all of these devices...

25
Operations
24
Turning the power on and offOperations
■ Connecting the power cord1
Insert the power cord connector into
the AC IN socket of the projector.
2
Insert the power cord plug into a
wall or other power outlet.The ON/STANDBY indicator will
change to orange, indicating standby
mode.
■Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.
■Turning the power on
Press the ON/STANDBY
button.
When the beep sound...

27
Operations
26
1
Turn on the power.Turn on the power by following the instructions in “Turning the power on” 
p.25
.
2
 Select the language and the lamp power (When using the
first time).When the projector is used for the first time after purchase, the start menu for lan-
guage (to display the menus and messages on the screen) and lamp power selection
and configuration is displayed in English. (If the screen is out of focus, adjust it
according to the step 
6.)
qUse the 
 or 
 button to select the...

29
Operations
28
■Using auto setting 
(Only for input from computer)
This function sets up the projector to the optimum state such as
sampling phase, frequency, screen position, and clamp for each
type of the input signal by using simple operations.
Press the remote control’s AUTO SET button.For computer input, the 
 icon will appear during processing.
You can set as well by selecting [Auto setting] in the Image
adjustment menu 
p.37
.
Notes•The image may not be projected or auto adjustment/setting may...

31
Operations
30
Notes•The 
 icon appears while resizing.
• Operating a function other than Mute will release resizing.
• As zooming is processed digitally, the image quality is degraded in larger zoom
ra tio.
• During resizing or moving the zooming area, the image may be distorted.
■ Cutting off the picture and sound temporarily (Mute)
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be
turned off.
Press the remote...

33
Operations
32
■Setting the password
How to change passwordThe default password is  0000.
1
Select [Password] in the Default setting 2 menu and press the 
 or
 button.
2
Select [Password registration] in the password registration, setting
menu, and press the 
 button.
The password entry screen is displayed.
3
Enter the current password (4-digit number).•Enter a 4-digit number for the password using numeric keys of the remote control.
• Enter [0000] (4 zeros) for the first change.
• The password is not...

35
Operations
34
How to set password (from [Off] to [On])
1
Select [Password] in the Default setting 2 menu and press the 
 or
 button.
2
Select [Password setting] in the password registration, setting menu,
and press the 
 or 
 button.
3
Select [On].
4
Select [OK] and press the 
 button.
The password entry screen is displayed.
5
Enter the password using numeric keys of the remote control.
6
The password setting will be set as [On].How to operate when password is [On]
1
Turn on the power.
2
The lamp...

37
Operations
36
■The image adjustment menuUse this menu to set or adjust image-related items. Items that can be set or adjusted are
marked with “Yes”, and those that cannot are marked with “No”. (When an item is masked,
it indicates that you cannot select for the current input.)
Camera
Item 
  
Description
Computer Y/P
B/PRVideo
S-video
(XC2500A/XC3000A)
 
Contrast Adjust the image contrast. Yes Yes Yes Yes Yes
Lower
Higher
Brightness Adjust the brightness of the image. Yes Yes Yes Yes Yes
Darker...

39
Operations
38
■The display setting menuUse this menu to set screen display-related items.
(The items in gray color cannot be set with the current input selection.)
Language Up/down  
shift
Background
IconBlackboard 
modeStart-up screen
User logo
  (Full):  Display with 1024  × 768 dot resolution
  (Thru): 
Display with sampling resolution (for computer input only)
 (Wide):  Wide-screen display
Lets the projected image shift vertically when the screen size setting 
is wide display (within the range of...