Toshiba Projector Tlp Xc2000 User Manual

							21
20
Preparations
Operating a computer using the remote controlA computer can be operated using the projector’s remote control.  This function is available
on any computer with the Windows
® 98/98SE, Windows
® Me, Windows
® 2000, or Win-
dows
® XP OS, that is equipped with a USB port which can support USB1.1 (The mouse
remote control receiver is also supported on OS 9 or OS X for the Macintosh).  However,
please note that Toshiba does not guarantee the operation of all computers.
1
Connecting a computerConnect the mouse remote control receiver (supplied) to a computer.Mouse remote control receiver To USB port2
Operating a computerOperate remote control’s buttons towards the mouse remote control receiver.
●
Moving the mouse pointer
Press the mouse control button in the direction you wish the mouse pointer to move,
then press.
● To left click
Press the L-CLICK button.
● To right click
Press the R-CLICK button.
● To drag and drop
Holding down the L-CLICK button, move the mouse control button until the mouse
pointer is over the desired location, then release the L-CLICK button.
● Using the computer’s page up  [
↑ ]
 and down  [
↓ ]
 function
Press the PAGE+ and PAGE- buttons to switch PowerPoint
® slides.
The remote control may fail to operate
if the mouse remote control receiver is
exposed to bright sunlight or
fluorescent lighting.
In such a case, change position or
direction of the mouse remote control
receiver and retry.
Mouse control
Remote Control Front Remote Control Rear
PAGE – PAGE +
R-CLICK L-CLICK
■
Operating the remote
controlTurn on the ON/OFF switch of the
remote control.
Point toward the projector’s
infrared remote sensor, and press a
button on the remote control.• Operating the projector from the front
Approx. 15 °Approx. 5m
■Loading dry-cell batteries
into the remote controlq Remove the battery cover.wInsert the dry-cell batteries.
Be sure to align the plus and minus
ends of the batteries properly.Two batteries (LR03, SIZE AAA) are
used.
e Replace the battery cover. Dry-cell batteries•Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
• Remove batteries from remote control when not using for extended periods.
• If the remote control stops working, or if its range decreases, replace all the batteries with
new ones. The remote control•When using more than 2 projectors, [ Remote control] can make it possible to operate
the remote control individually. 
p.43
•T urn off the ON/OFF switch of the remote control when not in use or to store in baggage.
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Do not drop or bang.
• Do not leave in hot or humid locations.
• Do not get wet or place on top of wet objects.
• Do not take apart.
• In rare cases, ambient conditions could impede the operation of the remote control. If this
happens, point the remote control at the main unit again, and repeat the operation.Preparing and using the remote control
When operating the remote control
from behind the projector, the light is
reflected on the projecting surface
and may travel a shorter distance to
reach the projector depending on the
shape and material of the projecting
surface. 
						

							23
22
Preparations
p.59
Video recorder,
DVD player, etc.
To audio output
White (L)/Red (R)
S-video cable
(not supplied)
To S-video output
Before connection•Read the owner’s manual of the device you are connecting to the projector.
•Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal 
p.57
, etc.
•Turn off the power of both devices before connecting.
•The figure is a sample connection. This does not mean that all of these devices can or
must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Connection
Computer
(for control)Computer
To
RS-232C
terminal
Audio cable
(not supplied) To audio output
Control cable
RGB cable
(supplied) To  RGB
output
Computer
Audio cable
(not supplied)To audio
output
Audio cable
(not supplied)
RGB cable
(not supplied)To  RGB
output
Placement StylesAs shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the
Default setting 2 menu, in accordance with your needs. 
p.43
Placement
 WARNING
•Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus
resulting in injury.
•If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the
projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.
Improper mounting could cause the projector to fall, resulting in an accident.
•If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let
everyone involved with the use of the projector know that fact.Floor-mounted front projection 
Floor-mounted rear projection 
Ceiling-mounted front projection 
Ceiling-mounted rear projection 
Projection Distance and SizeUse the figures, tables, and formulas below to determine the projection size and projection
distance. (Projection sizes are approximate values for full-size picture with no keystone
adjustment.)Screen
As seen from above
As seen from the side 90°90°
a H
Lens center
a (min length) = projection size (inches) – 0.8786
32.773
a (max length) = projection size (inches) – 0.7244
27.248
a is the distance (m) between the lens and the screen,
and corresponds to a range of 1.19 m to 9.13 m. H is the
height from the image bottom to the center of the lens.
Audio amplifier, etc. DVD video recorder, etc. Video recorder, etc.
Conversion
adapter BNC-pin
(not supplied) Monitor cable Mini
D-sub 15P-BNC
(not supplied)
To audio input
White (L)/Red (R)
AV  cable
(not supplied)
To video
outputAudio cable
(not supplied)Audio cable
(not supplied)
To audio
outputTo  Y/C
B/CR output
Green (Y)/Blue
(C
B)/Red (C
R)
To audio
output
White (L)/
Red (R)It is necessary to
switch to MONITOR
OUT by the switch.Monitor
p.18
projectionprojection distance a (m)
height (H)
min length max lengthsize (cm)
(zooming max) (zooming min)(cm)33 (84) – 1.19 6.040 (102) 1.19 1.44 7.360 (152) 1.80 2.18 10.980 (203) 2.41 2.91 14.5100 (254) 3.02 3.64 18.1150 (381) 4.55 5.48 27.2200 (508) 6.08 7.31 36.3250 (635) 7.60 9.15 45.4
300 (762) 9.13 – 54.4 
						

							25
Operations
24
Turning the power on and offOperations
■Connecting the power cord1
Insert the power cord connector into
the AC IN socket of the projector.
2
Insert the power cord plug into a
wall or other power outlet.The ON/STANDBY indicator will
change to orange, indicating standby
mode.
■Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.
■Turning the power on
Press the ON/STANDBY
button.
When the beep sound is [On], the
projector beeps, the power turns on,
and the ON/STANDBY indicator lights
in green. After a moment, the start-up
screen appears. CAUTION
•Do not look into the lens while the lamp is on.  The strong light from the lamp may cause
damage to your eyes or sight.
•Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
•Do not place your hands, face, or other objects near the air exhaust. Doing so could cause
burns, deform/break the object.
Power cord connector
(Supplied)
Start-up screen Control panelRemote
Control
Notes
•When COMPUTER 2 IN terminal (also used for MONITOR OUT terminal) is used as
MONITOR OUT terminal, the signal which is input to COMPUTER 1 IN terminal is output.
•Signals are output from MONITOR OUT terminal even in standby mode.
   However, from AUDIO OUT terminal, no audio signal is output.
•A computer monitor cannot accept Y/P
B/PR signals correctly.
•The AUDIO IN terminal doubles for devices connected to COMPUTER 1 terminal and
COMPUTER 2 terminal.
•When an AUDIO OUT terminal is connected, sound is not output from the projector
speaker.
•Output volume of AUDIO OUT terminal can be adjusted by the VOL button.
•Moving pictures played back on computers using DVD software may appear unnatural if it
is projected with this projector, but it is not a malfunction.
Label locationsConnection (Continued)Caution – use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
TLP-X2000
TLP-XC2000
TLP-XC2000
Remote control Document camera 
						

							27
Operations
26
1
Turn on the power.Turn on the power by following the instructions in “Turning the power on” 
p.25
.
2
 Select the language and the lamp power (When using the
first time).When the projector is used for the first time after purchase, the start menu for lan-
guage (to display the menus and messages on the screen) and lamp power selection
and configuration is displayed in English. (If the screen is out of focus, adjust it
according to the step 
6.)
qUse the 
 or 
 button to select the
desired language and press the 
 button.
Message for setup confirmation is displayed in a
selected language.
Then, the menu for lamp power selection and
configuration is displayed. It is automatically set as
Standard. To change the setting, follow the step w.
wUse the 
 or 
 button to select the lamp
power and press the 
 button.
The lamp power, if selected, will be toggled without
pressing the 
 button. The display automatically
disappears in a few seconds.
Notes•When the projector is turned on the next time, the start menu does not appear upon
startup. However, if [Reset all] is executed from the Default setting 2 menu 
p.43
,
the start menu will be displayed the next time when the power is turned on.
•The language can also be set via the Display setting menu 
p.39
 and Lamp power
via the Default setting 1 menu 
p.42
.
•This owner’s manual assumes that English has been selected.
3
Activate the connected device.Turn on and start the connected device such as a computer.
4
Press the INPUT button.An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.Notes
•When [Auto input search] is set to [Off] in the Default setting 1 menu 
p.42
 (factory
setting is [On]), the Input select menu appears if you press the INPUT button.
•If no signal is being output from the connected equipment, pressing the INPUT button
does not change the input and “There is no other input signal.” will appear.
Basic operations
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Polish
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Notes
•The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu 
p.39
.
•The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed 
p.27
.
•Beep sound can be set not to beep in the Default setting 1 menu 
p.42
.
•When [Key lock] is [On], the operation buttons of the projector do not work 
p.43
.
•When [Password setting] is [On], then the start-up screen is displayed after the
Password entry screen disappears 
p.33
.
■Turning the power off1
Press the ON/STANDBY button.A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button once again.When the setting of beep sound is [On], the projector beeps, and the screen turns off,
but the internal cooling fan continues to operate. Then, the projector goes into standby
mode.
During cooling, the ON/STANDBY indicator flashes. While the
indicator is flashing, the power can not be turned back on. At this
point of time, it does not matter even if you unplug the power
cord.Note
•The projector consumes about 10W of power in standby. We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
PRECAUTION
•If you turn the power on before cooling is complete, give the lamp time (about 5 minutes)
to cool before plugging it back in. If the lamp overheats, it may fail to light.Turning the power on and off (Continued)
LCD Panels
LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the
following precautions.
•In order to extend the lifetime of the LCD panel, always turn off the power when not in
use, and make sure that the lamp is off. Keeping the lamp off is also very effective at
saving electricity.
•If the air filter becomes dirty and clogged, the projector’s internal temperature will rise,
shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter
from time to time 
p.52
, and replace it periodically. Contact the store where you
purchased your projector, or your local Service Station for replacement air filters. 
						

							29
Operations
28
■Using auto setting 
(Only for input from computer)
This function sets up the projector to the optimum state such as
sampling phase, frequency, screen position, and clamp for each
type of the input signal by using simple operations.
Press the remote control’s AUTO SET button.For computer input, the 
 icon will appear during processing.
You can set as well by selecting [Auto setting] in the Image
adjustment menu 
p.37
.
Notes•The image may not be projected or auto adjustment/setting may not be performed
correctly for input signals other than those supported by the projector 
p.57
, p.58
.
•If auto setting fails adjustment, adjust manually with [Position] in the Image
adjustment menu 
p.37
.
■Correcting the keystone distortion
When the projector placement angle against the
screen is changed while projecting the image,
the picture will undergo keystone (trapezoidal)
distortion.This projector is capable of correcting this keystone
distortion
.
1
Press the KEYSTONE button.The Keystone menu appears. By default, [Auto v-keystone] is selected.
Item Description
Automatically corrects the vertical distortion.
Press      .
Screen shrinking at Screen shrinking at 
bottom top
Auto  v-keystone
V-keystone
Using handy features
Control panelRemote
Control
Before correction
After correction
Remote
Control
5
Projector placement angle adjustmentsThe placement angle and the height of the projected image can be adjusted by the foot
adjuster.qLift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
wTo fine adjust the angle, twist the
foot adjuster.
eTo adjust the horizontal angle, use
the right and left tilt adjusters.•To stow the foot adjuster, hold up the projec-
tor while pressing the foot adjuster release
button, then slowly lower the projector.
6
Adjusting the screen size and focusq
Use the zooming lever to adjust the screen size.
wUse the focusing ring to adjust the focus.
7
Adjusting the volume with the 
 
 buttons
The speaker volume can be adjusted when an audio signal is being input.Notes
•Note that lamp characteristics may rarely cause the brightness to fluctuate slightly.
•A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out.  This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
•The LCD panel is made using extremely advanced technology, but there may be black
spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.
Please note that these are not malfunctions.
•Although this projector supports a wide range of RGB signals 
p.57
, any resolutions not
supported by this projector (XGA) will be expanded or shrunk, which will affect image
quality slightly. To view high-quality images, it is recommended that the computer’s
external output should be set to XGA resolution.
•With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
•If no signal is being input from the connected equipment or signal input is stopped while
projecting, the “No signal” will appear.
•If a signal not supported by the projector is input, the “Unsupport signal” will appear.
•If an unavailable operation button is pressed, the 
 icon will appear.
Basic operation (Continued) 
						

							31
Operations
30
Notes•The 
 icon appears while resizing.
• Operating a function other than Mute will release resizing.
• As zooming is processed digitally, the image quality is degraded in larger zoom
ra tio.
• During resizing or moving the zooming area, the image may be distorted.
■ Cutting off the picture and sound temporarily (Mute)
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images and sound can be
turned off.
Press the remote control’s MUTE button.The picture and sound are cut off. (The Mute function is released
when pressing the  MUTE button again.)Notes• The 
 icon will appear while mute is in effect.
• Operating any other functions will also cancel the muting.
■ Changing picture mode
The projected image mode can be selected.
Press the remote control’s PICTURE button.1
The Picture mode menu appears.1/2/3
2
Select a mode using 
 
 then press 
.
Though the 
 button is not pressed, the picture mode
changes as the setting is changed and the display turns off
automatically in a few seconds.
Note•[ Picture mode ] of the Image adjustment  menu has the same
function 
p.37
.
Remote Control
Using handy features (Continued)
Adjusting Keystone distortion [Auto]2
Press the 
 button.
The keystone distortion is automatically corrected. The 
 icon appears during this
correction.
When adjustment is finished, the  Keystone menu appears again. For fine adjust-
ment, select [ V-keystone ] by the 
 button and adjust image manually by the 
 buttons.
Adjusting Keystone distortion [Manual]2
Select [V-keystone] by the 
 button.
3
Use the 
 
 buttons for keystone adjustment.
Note•Depending on the amount of keystone adjustment and the content of images, some
information may be lost, or the picture quality may suffer.
■ Resizing image
The projected image can be resized (zoomed in/out).1
Press the remote control’s RESIZE 
 button.
Each time you press the  RESIZE 
 button, zoom ratio is up. You can keep
pressing.
2
To  zoom out, press the remote control’s RESIZE
 button.
Each time you press the  RESIZE 
 button, zoom ratio is
down. You can keep pressing.
(However, the image cannot be smaller than the original
size.)
3
To  move the area to zoom in, use the 
 
 
 
buttons.You can keep pressing.
4
To  reset the zoom, press the RETURN button.The image is reset to the original size.
Remote
Control Remote
Control 
						

							33
Operations
32
■Setting the password
How to change passwordThe default password is 0000.
1
Select [Password] in the Default setting 2 menu and press the 
 or
 button.
2
Select [Password registration] in the password registration, setting
menu, and press the 
 button.
The password entry screen is displayed.
3
Enter the current password (4-digit number).•Enter a 4-digit number for the password using numeric keys of the remote control.
•Enter [0000] (4 zeros) for the first change.
•The password is not displayed. Instead it appears as [****].
4
Enter a new password (4-digit number).
5
Re-enter the same password for confirmation. Note•Please do not forget your password. If you forget the password, you can not
release the password by yourself.
In such a case, please inquire your dealer.
Using handy features (Continued)■Changing screen size
The screen size for the projected image can be changed.
Press the remote control’s SCREEN SIZE button.Pressing the button switches Full/Thru/Wide in turn.Notes•Thru display is available for computer-input images.
•[Screen size] of the Display setting menu has the same functionp.39
.
•If you use this function on commercial video software, broadcast
or cable-broadcasting except for the purpose of your private
viewing and listening, it may infringe the copyright protected by
the copyright laws.
■Freezing the image (Freeze)
The image being projected can be frozen. This function is to be used
to pause a video during a presentation, etc.
Press the remote control’s FREEZE button.The picture pauses. (The Freeze function is released when
pressing the FREEZE button again.)Notes•The 
 icon will appear while freeze is in effect.
•Other operation will also release the freeze.
•Even if an image is frozen on the projector, the pictures are
running on the video or other equipment.
•If you use this function on commercial video software, broadcast
or cable-broadcasting except for the purpose of your private
viewing and listening, it may infringe the copyright protected by
the copyright laws.
Remote
ControlRemote
Control 
						

							35
Operations
34
How to set password (from [Off] to [On])
1
Select [Password] in the Default setting 2 menu and press the 
 or
 button.
2
Select [Password setting] in the password registration, setting menu,
and press the 
 or 
 button.
3
Select [On].
4
Select [OK] and press the 
 button.
The password entry screen is displayed.
5
Enter the password using numeric keys of the remote control.
6
The password setting will be set as [On].How to operate when password is [On]
1
Turn on the power.
2
The lamp lights and the password entry screen appears.
3
Enter the password using numeric keys of the remote control.If the entered password is correct, the start-up screen appears and the projector
goes into normal operation. If the password is wrong, a message appears to
prompt you to re-enter the password, and again the password entry screen is
displayed. If you enter a wrong password for more than 5 times, the projector will
automatically power off and enter standby mode.Note•Even if you have forgot the password setting, the password setting can be forcibly
set to [On], by detaching the control panel from the projector first when the power is
turned back on after the power cord has been unplugged.
If you can not change the previous password, please input [0000] (4 zeros) using
numeric keys of the remote control.
Using handy features (Continued)
How to set password (from [On] to [Off])
1
Select [Password] in the Default setting 2 menu and press the 
 or
 button.
The password entry screen is displayed.
2
Enter the password using numeric keys of the remote control.
3
Select [Password setting] in the password registration, setting menu,
and press the 
 or 
 button.
4
Select [OFF].
5
Select [OK] and press the 
 button.
Note•While the password setting is [On], the password entry screen will be displayed
only when the power is turned on next time. 
						

							37
Operations
36
■The image adjustment menuUse this menu to set or adjust image-related items. Items that can be set or adjusted are
marked with “Yes”, and those that cannot are marked with “No”. (When an item is masked,
it indicates that you cannot select for the current input.)
Item 
  
Description
Computer Y/P
B/PRVideo
S-video Camera
(XC2000)
 
Contrast
Adjust the image contrast. Yes Yes Yes Yes Yes
Lower
Higher
Brightness Adjust the brightness of the image. Yes Yes Yes Yes Yes
Darker
Brighter
Color Adjust the color of the image. No Yes Yes Yes No
Lighter
Deeper
Sharpness Adjust the sharpness of the image. Yes Yes Yes Yes Yes
Softer
Sharper
Noise Set the function to reduce screen noise. No Yes Yes Yes No
reduction
*1
On (Enable)
Off (Disable)
Picture mode Press 
. T oggle the picture mode with Yes Yes Yes Yes No
 
.     1/2/3
/
/
R-level Adjust red of the image color. Yes Yes Yes Yes Yes
Less red
More red
G-level Adjust green of the image color. Yes Yes Yes Yes Yes
Less green
More green
B-level Adjust blue of the image color. Yes Yes Yes Yes Yes
Less blue
More blue
NTSC mode
*2
Set the black level with 
 
.NoNoYesYesNo
US : NTSC (US) mode
JA PA N: NTSC (JAPAN) mode
 Auto setting Automatically adjusts items such as the Yes No No No No
samplingphase depending on the type of
input signal.Position Press 
 then change mode using 
 
Ye s N o N o N o N o
and adjust with 
 
.
 Phase Ye s N o N o N o N o
Adjust to eliminate flicker. Frequency Ye s N o N o N o N o
Adjust to eliminate periodic patterns and
flickering when many fine vertical lines
appear on the screen. H-position Ye s N o N o N o N o
Adjust the horizontal position of the image.
Y ou can call up on-screen menus, and conduct a number of adjustments and settings using
the operation buttons 
p.16
 on the control panel (main unit side) and remote control.
■ How to use the menus
The menu shown below is for operation instructions purposes and might differ from the
actual display.
Using the menus
Toggle items with            .  
Select items with             and press       . 
Fix selection with       .
Display the  Setting display  menu.
1. Press the MENU button
2. Select a Category
3. Adjustments & SettingsSelect a category by using  
         .
There are following 5 categories: Displays the current 
adjustments and 
settings of selected 
category.
Item shown with gray 
cannot be adjusted with 
the current input source.p.37
Image adjustment
 menu
p.39
Display setting menu
Default setting 1  menu
p.42
•  The figure shows displays given for operation instructions purposes.  As the display may differ depending on the item, 
use the following pages as a reference.
•  To return to previous item, press the RETURN button.
Item
Adjustment/Setting ValueThese marks signify 
the items can be 
adjusted/set by using
             .
These marks signify the items can 
be selected from the list by using 
            .
After an item is selected, apply it by 
pressing       .
Press       or       to open the menu.
Default setting 2  menu
p.43
Status display menu
p.44
These marks 
signify that there 
are options. 
Press        or         
to display a list of 
options.
These marks 
signify that 
there are setting 
screens. Press 
       or       to 
display a list of 
setting screens.
* When no item is 
changed, press       .
4. End  Press the MENU button.  (The menu disappears about 30 seconds after the last operation.) 
						

							39
Operations
38
■The display setting menuUse this menu to set screen display-related items.
(The items in gray color cannot be set with the current input selection.)
Language Up/down  
shift
Background
IconBlackboard 
modeStart-up screen
User logo
 (Full):  Display with 1024 × 768 dot resolution
 (Thru): 
Display with sampling resolution (for computer input only)
 (Wide):  Wide-screen display
Lets the projected image shift vertically when the screen size setting 
is wide display (within the range of 1024 × 768).
When projecting on a non-screen surface, select a color in accordance 
with the projecting surface.
Press      and switch with       and      .  
Off/Green/Black/Brown/Blue/Beige
Select one of the languages below to use for displaying the menu and messages[      or      : Enter setting mode]     [          :Selection]      [Apply:       ]
English/Français/Deutsch/Italiano/Español/Português/               / 
Svenska/Türkçe/Polski/            /                      /                      /
Screen to display when there is no input signal 
[      or      : Enter setting mode]     [          :Selection]      [Apply:       ] 
Logo/Blue/None
Display icons as function guides On Off
Display start-up screen when power is turned on On Off
Display a logo customized by the user for the start-up screen or when 
there is no input signal.
[      or      : Enter setting mode]     [          : Selection]
      Logo registration  Press       to display the registration menu.
      Display style
      Background Black           Blue           White
      Logo confirmation  Press      .
      Reset logo Yes           NoDescription
Item
Screen size
Detailed description
[Screen size]•If “Thru” is selected for [Screen size], portions exceeding the native resolution
(1024 × 768 pixels) will not appear on the screen. Note that for RGB signals with
clock frequency 140MHz or lower, all input pixel signals are sampled. However, if
the clock speed is higher than this, the RGB pixel signal is thinned before
sampling. Item 
  
Description
Computer Y/P
B/PRVideo
S-videoCamera
(XC2000)
Position
 V-positionYe s N o N o N o N o
Adjust the vertical position of the image. Clamp 1Ye s N o N o N o N o
Adjusts the clamp pulse position. Clamp 2Ye s N o N o N o N o
Adjusts the clamp pulse width.
*1: [Noise reduction] may not work depending on signal type.
*2: [[NTSC mode] can be displayed and adjusted only when the video signal is set to [NTSC] or
[NTSC4.43]. NTSC mode is set to JAPAN when the language is set to Japanese. It is set to US for
other languages.Using the menus (Continued)