Toshiba Projector Tlp X3000a User Manual

							41
Operations
40
Notes•You can register a logo from computer input only.
•The area that can be registered is 512 × 384 dots at the center of the screen. To
register a company logo, prepare the image within the limit.
•Only one logo can be registered. When a new image is registered, the old one is
erased.
•The time needed to register or display the image varies depending on the data size.
•If you use this function on commercial video software, broadcast or cable-
broadcasting except for the purpose of your private viewing and listening, it may
infringe the copyright protected by the copyright laws.Select the size of the registered logo.
:Displays the registered image in original size at center of the screen.:Displays the registered image by enlarging fully in the screen.
(As processed digitally, the image quality is degraded.)
Sets background color when [Center] is selected for the logo [Display style].You can preview the registered logo.You can reset the registered logo, display style and background  to the factory
setting. (The logo set for the start-up screen and background is reset.)
Note
•If you use the screen size setting function on commercial video software,
broadcast or cable-broadcasting programs to display images with the varying
aspect ratio except for the purpose of your private viewing and listening, it may
infringe the copyright protected by the copyright laws.[Up/down shift]Shifts the projected image vertically when [Screen size] is [Wide].[Blackboard mode]Projects the image in colors more like projecting on a screen.
Precaution•The projected image may differ depending on the type, color, and material of the
blackboard and wall even if the selected color is the same as the projected
screen.[Background]•TOSHIBA is set for [Logo] by factory setting.
•If user’s logo has been registered, it is displayed when [Logo] is set for
background.[Start-up screen]If user’s logo has been registered and this setting is [On], the logo is displayed at
start-up.[User logo]Registers a part of the image that is input from computer, as a stationary picture
and displays it as a logo at start-up and when no signal is input.
How to register user logo1
Select [User logo] in the Display setting menu, and press the or 
 button.
2
Select  from the displayed menu list and
press the 
 button.
3
The registration area is displayed for confirmation. Select [OK]
or [Cancel] and press the 
 button.
•If the registered picture does not fall within the display area, operate the
computer to scroll the screen.
4
Select [Yes] to register and press the 
 button.
5
Registration starts.•A message is displayed while registration is in process.
Using the menus (Continued) 
						

							43
Operations
42
■The default setting menuThis menu shows placement status and other settings.Default setting 1 menu
Description Item
Set the time to wait for the power to be turned off after the last 
operation is made with no input signal. 
Set whether the input with signals is only selected or not. 
Beep when operation is made.
Sets whether to turn on the power when the ON/STANDBY button is 
pressed (Manual), or when the power cord is plugged in (Auto).  
Sets the lamp power.                                    No signal 
power off
Auto input 
search
Beep
Power on
Lamp power
Manual             Auto
On             OffOn             Off
Low           Standard
Off (not turned off)            30 min.
Detailed description
[Auto input search][On]: Automatically searches the signals that
can be projected, and switches input
from the connected device that outputs
the video signals each time the INPUT
button is pressed. The input from the
connected device that outputs no video
signals is skipped.
[Off]: Displays the Input select menu.
Toggle with 
 
 buttons and press 
button. (The input without signals can be
selected.)
[Power on]Note that if [Power on] is set to [Auto], then if the power is supplied when restored
after a power outage, the projector will come on.[Lamp power]When [Lamp power] is set to [Low], the screen becomes a little darker, but the
cooling fan noise gets quieter.
Default setting 2 menu
Description Item
Sets projection mode in accordance with Placement Style. 
Sets the cooling fan speed.
When two or more projectors are used and controlled by the remote 
control respectively, this menu sets the code for the projector and the 
remote control. 
[      or      : Enter setting mode]      [           : Select from 1, 2, 3, 4]       
[     :Confirm]      [           :Select OK to end] 
Press [Cancel] to return.
Lock the control panel buttons. 
[      or      : Enter setting mode]      [           : Select On/Off]       
[     :Confirm]      [           :Select OK to end]   
Press [Cancel] to return.
Press       . (The password and user logo are not reset.) 
Resets all adjustments and settings to their factory settings. 
Password setting Projection
mode
Fan mode
Remote 
control 
Key lock
Reset all
PasswordYe s            No
Standard           High
(Rear 
ceiling)
(Standard)
(Rear) (Ceiling)
p.22
p.33
Detailed description
[Fan mode]Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan
noise gets louder.) Set this option to use the projector, for example, at high altitude
(over 1,500 meters above sea level).
•Do not set Fan mode to [High] when using the projector at a lower altitude.[Remote control]Sets a remote control code from 4 types. You can set each code respectively for up
to 4 projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
•You cannot operate the remote control if the codes of the projector and the
remote control do not match.Remote control code setting for remote controlRemove the battery cover and set the same remote control code switch as the
projector. 
p.16
 p.17
 (Use a screwdriver with thin tip to set.)
Using the menus (Continued)
Computer 1
Y/P
B/PR 1
Computer 2
Y/P
B/PR 2
Video
S-video Input select




/



shows whether signal is 
 input or not.
Input select menu 
						

							45
Operations
44
Using the menus (Continued)
[Key lock ]Protect from operating errors by locking on the control panel buttons of the
projector. (The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly
operation with the control panel buttons is disabled.
•To release the key lock, set the [ Key Lock] to [Off] using remote control. Pressing
the [ RETURN ] button on the projector for 10 seconds also sets the [ Key Lock] to
[ Off ]. (When operating the main unit, the 2 indicators of LAMP and TEMP light in
orange for 3 seconds, and at the same time the projector beeps.)
■ Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Camera
Item Description
Computer Y/P
B/PR
Video S-video
(XC2500A/XC3000A)
ProjectorInput Input source name Yes Yes Yes Yes YesMode name RGB input mode 
[Note 1]
Ye s N o N oNo No
Resolution Resolution (in dots) Yes No No No NoFrequency Sync frequency Yes No No No NoSync Sync signal polarity 
[Note 2]
Ye s N o N oNo No
Signal format Y/P
B/PR signal format No Yes No No No
Video mode Color method of video signal No No Yes Yes NoLamp time Time of lamp use 
[Note 3]
Ye s Ye s Ye s Ye s Ye s
Lamp reset count The count for lamp replacement Yes Yes Yes Yes Yes
T otal time The total time that this projector
is used. Ye s Ye s Ye s Ye s Ye s
V ersion Firmware version 
[Note 4]
Ye s Ye s Ye s Ye s Ye s
Notes
1: The mode of supported RGB signals 
p.57
 is shown.
2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [ Lamp time ] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) Please replace the lamp after 2000 hours of use if [ Lamp
power ] is set to [ Standard], or after 3000 hours of use if [ Lamp power] is set to [Low], consult
with a dealer about getting replacement for lamp TLPLW11 (sold separately).
4: [ Version ] shows the version of the projector’s internal control program. This version is referred
to for customer service, etc.
Note• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
Please read this chapter if the model you purchased includes a document camera.■ Preparation of the document camera
1) Setup the arm
Status before preparation
(When stored)
3) Let the camera lens face below 2) Raise the camera head
4) Let the camera lens face the object
PRECAUTIONS
• Do not jolt or force the camera head or camera arm. Doing so could cause malfunction.
• The CMOS image sensor mounted on the camera of this projector is produced by
precision engineering. Please be informed that missing pixels and bright spots are not
considered as problems.
Note
•It takes about 10 seconds from when the power is turned on until the operation is
possible. This is not a problem.Using the document camera 
						

							47
Operations
46
Using the document camera (Continued)■Image projection with the document camera1
Press the LED LIGHT button.The illumination LED lights. CAUTION
•Please do not look into the lighting LED directly. The strong light may cause damage
to the eyes or sight.2
Place the document.Set the document at the side of the projector.
3
Press the CAMERA button, and select camera input.•The input returns to the previous input when the CAMERA
button is pressed again.
•Camera input can also be selected by pressing either the
remote control or projector’s INPUT button.
4
Rotate the camera head to align the orientation of the document for
shooting by checking the screen.
5
Move the camera arm up and down to adjust the image size.•When projecting the document of A4 size (210 mm ×
297 mm), please adjust the height of the camera head
to about 43 cm. Notes•You can use the RESIZE function of the remote controller to change the size of an
image. 
p.30
•In the camera input mode, the image may disappear for a moment. This is not a
problem.
6
Adjust the focus with the focusing ring of the camera
head.Adjust by rotating the focusing ring of the camera head until the
projected image becomes clear.
7
If the screen is too dark or too bright, use the CAMERA
GAIN (+/–) buttons to make it easier to see.
8
Fold up the camera using the reverse order from
unfolding the document camera.Fold up with the reverse steps of “Preparation of the
document camera”.PRECAUTION
•If the rooms fluorescent lighting causes the image to flicker, either
change the Shutter setting of shutter speed by 50/60Hz switch, or
turn off the fluorescent light. Note that changing the Shutter setting
may not eliminate the flicker, depending on the state of lighting,
document or image adjustment.
Note
•There is no audio output when the camera input is selected.Closer: Larger image Farther: Smaller image
43 cm 
						

							48
49
Maintenance
The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.•The lamp may burst with a loud noise due to impact or deterioration, or fail to light at
the expiration of its life.
•How long it takes before the lamp bursts or the life expires may vary greatly by lamp.
Some may burst shortly after first use.
•Burst is likely to happen if the lamp is used after the replacement period has elapsed.
•When the lamp bursts, the broken pieces of glass may get inside the product or be
released outside from the openings for ventilation.
•When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with
glass dust may be released from the openings for ventilation.■
Immediately replace the lamp when a sign appears on the screen.•When the replacement time approaches, a message will appear on the screen.
•The risk of burst will increase if the lamp is continuously used without being replaced.
•Frequently check the used hours and prepare spares when the replacement time
approaches. (Refer to “Status display”. 
p.44
)
■
When the lamp is broken•If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
•In the event of lamp burst, unplug the product from the wall outlet, leave and completely
ventilate the room. Then, thoroughly clean the area around the projector and discard
any edible items placed in that area.
•When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes
or you breathe it.About lampMaintenance
Using the document camera (Continued)■Locking the white balanceAlthough the projector’s camera is constantly adjusting the color balance of the images it
photographs, the color balance may be disrupted, depending on the color layout of the
document. If this happens, the white balance can be locked using the procedures below.1
Lay down a piece of white paper, and adjust so it fills the screen.Adjust the camera head and arm so that the white paper fills the screen completely.
2
Press W.BALANCE button and lock the white
balance.The LOCK indicator which shows the white balance has
been locked lights. If you want to return to the auto
adjustment, please press W.BALANCE once again. The
LOCK indicator will be off.Notes
•If the white balance is set to [Lock], once power is turned off or the arm is pushed down,
the setting goes back to [Auto].
•The color of the room lighting may prevent the white balance from being adjusted to the
optimum level. In this situation, of if you want to use a certain tinting, adjust the [R-level],
[G-level] and [B-level] on the Image adjustment menu. 
						

							51
Maintenance
50
5
Mount the new lamp.Align the orientation, press down the new lamp
until the bottom is reached, and lock in place using
the three lamp locking screws.
6
Replace the lamp cover.Align the cover, and press it in, then tighten the
screws loosened in step 
3 until the lamp cover is
no longer loose.
7
Reset the lamp time.See the lamp’s manual for instructions on resetting
the lamp time.Notes and Precautions
• The [ Lamp time ] item in the  Status display  menu indicates the time of lamp use (as a
rough guide) 
p.44
• Please replace the lamp after 2000 hours of use with [ Lamp power] in the Default
setting 1  menu set to [ Standard], and 3000 hours of use with [ Lamp power] in the
Default setting 1  menu set to [Low]. 
p.42
•There are cases that the lamp can not work before the above mentioned period expires
or before the replacement message is displayed.
• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
projector may fail to be powered on or the lamp may fail to come on.
• Always replace the lamp with a new one.
• The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
Used LampsThis projector’s lamps contain trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose of them in accordance with
local regulations.
1
Unplug power cord.
2
W ait until lamp is sufficiently cooled.Wait for at least 1 hour.
3
Remove the lamp cover.Loosen the two screws, raise the lamp cover
with your fingers as shown to remove the lamp
cover. Use care to avoid any damage to nails
and/or tip of your finger(s). If you have any
difficulty in removal, you can use a screwdriver
or any other smaller tool for your convenience.
4
Pull out the lamp.Loosen the three lamp locking screws, pull up the
handle, and remove the lamp.
Lamp cover
2
1
12
34
A lamp is consumable supplies. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime
of the lamp depends on condition of use.) If this happens, replace it with a new one
.
 W
ARNING
•If the projector is mounted on the ceiling, it is recommended to use you\
r Toshiba dealer-
ship when the lamp has to be exchanged.Uncovering the lamp while the projector is mounted on a ceiling may lead to a danger
of damage from falling pieces of glass if the lamp is broken. Besides, working at high
elevations can also be hazardous. Do not attempt to replace the lamp by yourself.
• When replacement is required, be sure to use TLPLW11 (sold separately). CAUTION
•
If you have been using the projector, the lamp will be very hot, and may cause burn
injuries. Wait for the lamp to cool (for longer than 1 hour) before replacing it.
• If the lamp should break, please handle with care to avoid injury due to broken pieces
(
p.49
) and contact your dealer for repair service.
5
12
Lamp replacement
•The lamp replacement message of this projector displays an appropriate period
according to the use period for [ Standard] / [Low ] of the [ Lamp power ] respectively.
• When the replacement time approaches, the message of “The lamp life is ending.
Please change the lamp.” and the icon 
 are displayed every time the power is
turned on. This display disappears when you press the 
 button.
  About lamp replacement messages 
						

							53
Maintenance
52
 WARNING
•Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership
.
Attempting to clean/replace the lamp at a high site by yourself may cause you to fall
down, thus resulting in injury.
■Lens cleaning•Clean the lens with a commercially available blower and/or
lens cleaner.
•The lens is easily scratched, so do not rub it with hard objects,
or strike it.■Main unit cleaning•Clean the main unit after unplugging the power cord.
•Wipe dirt off the main unit gently with a soft cloth.
•Do not wipe the main unit with a damp cloth. Doing
so may allow water to get inside, resulting in an
electric shock or failure.
•Do not use benzene, thinner and the like as they may
deform or discolor the unit or damage the paint
surface.
•When using a chemically treated cloth, follow the
precautions included with the cloth.Lens and main unit cleaning
Air filter cleaningThe air filter prevents dust and debris from getting inside the projector. Never run the
projector with the filter removed. It is recommended that the air filter is cleaned regularly.
•The message “Check the air filter for dirt.” is displayed every 100 hours. (If the usage time
exceeds 100 hours, this message is displayed for about 30 seconds when the image is
displayed for the first time after power is turned on. This display will be dismissed with any
operation.)
•Check out the filter and any debris is found, use the following procedure for cleaning.
 WARNING
•Request cleaning and maintenance of a ceiling-mounted unit from your projector
dealership.1
Unplug power cord.
2
Remove the air filter.Pull out the air filter by taking the catch shown in
the figure.
3
Clean the filter.Carefully remove the dust and dirt from the air filter
with a vacuum cleaner or the like.
4
Replace the air filter.Notes
•Allowing dirt and dust to build up in the air filter will worsen the air circulation inside the
projector, causing the internal temperature to rise, causing the projector to stop working
or malfunction.
•Insert the air filter all the way in. Leaving gaps will allow dust and dirt to get inside the
projector again.
•If you wash the air filer with water, make sure to dry it completely before replacing it.
•If the air filter is torn, consult with your dealer about replacing it with a new one.
Continuing to use a ripped filter will allow dust and dirt to get inside the projector. 
						

							55
Others
54
If you think something is wrong, check the followings before contacting customer service.
Please see “Trouble indications ” 
p.54
 as well.
If  This Happens Check
No powerPower goes out
during useNo pictureNo audioPicture not
displayed
correctlyPicture blurred
Part of picture
out of focusImage is darkColors too light
Bad shadingControl panel
key doesn’t workRemote control
doesn’t workBefore calling service personnel
• Is the power cord plugged in? Is it connected to the projector?
• Is the lamp cover attached properly? 
p.51
•Is the ambient temperature high? 
p.54
•Is the air intake or air exhaust blocked? 
p.54
•Is the projector turned on? (When [Auto input search] is [Off]) 
p.27
•Is the mute function on? 
p.31
•Is the brightness setting minimized? 
p.37
•Are the connections set up correctly? 
p.23
•Are all the connected devices functioning properly?
• Is the mute function on? 
p.31
•Is the volume setting minimized? 
p.28
•Are the connections set up correctly? 
p.23
•Are all the connected devices functioning properly?
• Is the input signal supported by the projector? 
p.57
, p.58
•Is there something generating an abnormal video signal, for
instance the video tape?
• Is the lens dirty? 
p.53
•Is the lens focus adjusted optimally? 
p.28
•Is the projection distance within the projector’s supported range? 
p.22
•Is the projector’s screen placement angle tilted too far?  
p.22
•Are the sharpness or sampling phase adjustments off? 
p.37
•Are the brightness or contrast adjustments off? 
p.37
•Is the lamp nearing the end of its service life? 
p.44
•Are the color, R-level, G-level, or B-level adjustments off? 
p.37
•Is the screen dirty?
• Is the blackboard mode set properly? 
p.39
•Is the lamp nearing the end of its service life? 
p.44
•Is the key lock function on? 
p.43
, p.44
•Has the control panel been installed properly? 
p.15
•Is the remote control ON/OFF switch set off? 
p.20
•Is the remote control code identical with the projectors code? 
p.43
•Are the remote control’s batteries drained?
• Are the batteries inserted into the remote control correctly? 
p.20
•Is the remote control being used within the effective range? 
p.20
•Are there any obstructions between the remote control and projector?•Are there any fluorescent or other bright lights shining at the
projector’s infrared remote sensor?
The indicator lights to inform you of internal abnormalities.
No power
⇒Problem with projector
• Unplug the power cord, and contact your dealer.Lamp went out during use, or won’t come on⇒ Lamp temperature is high so that it is difficult to turn on, the lifetime of the
lamp has ended or the projector is malfunctioning.
•Unplug the power cord and wait for a short while, then turn the power
back on.
• If a lamp burns out, replace it with a new one.
❈ The abnormal display will not disappear until the power cord is
unplugged.
You can not turn on the power during abnormal display.Power went out during use⇒ Internal overheating, or the outside temperature is too high.
• Place the projector so that the air intake and exhaust are not blocked.
• Unplug the power cord and wait for a short while, then turn the power
back on.
❈ The 
 icon will appear before the power goes out.
❈ The abnormal display will not disappear until the power cord is
unplugged.
You can not turn on the power during abnormal display.
Power went out during use⇒ Problem with internal cooling fan.
• Unplug the power cord, and contact your dealer.
❈ The 
 icon will appear before the power goes out.
❈ The abnormal display will not disappear until the power cord is
unplugged.
You can not turn on the power during abnormal display.
Power went out during use, or power won’t come on⇒ The lamp cover is not properly attached.
• Unplug the power cord, and reattach the lamp cover. 
p.51
❈ The abnormal display will not disappear until the power cord is
unplugged.
You can not turn on the power during abnormal display.
Power went out during use⇒ Problem inside the projector.
• Unplug the power cord and wait for a short while, then turn the power
back on.
• If the above action will not clear the problem, unplug  the power cord,
and contact your dealer.
❈ The 
 or 
 icon will appear before the power goes out.
❈ The abnormal display will not disappear until the power cord is
unplugged.
You can not turn on the power during abnormal display.
(Off)
(Red 
flashing) (Red lit)
(Red lit)
(Red lit) Or
(Red 
flashin
g)
(Red lit)
(Green 
flashin
g)
(Red lit)
(Orange
flashin
g) (Red lit)(Red lit) (Orange
lit)
Or(Orange
flashin
g)
T rouble indicationsOthers 
						

							57
Others
56
■List of supported signals (RGB signals)This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
Resolution
720 x 400
640 x 480
800 x 600
832 x 624
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
1400 x 1050
1600 x 1200 Mode
720x400_85 VGA_60
V GA_72
V GA_75
V GA_85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85 MAC16
XGA_60
XGA_70
XGA_75
XGA_85 MAC19
SXGA1_75
QuadVGA_60
QuadVGA_85 SXGA3_60
SXGA3_75
SXGA3_85 SXGA+
UXGA_60
UXGA_65
UXGA_70
UXGA_75
UXGA_85 Refresh rate
(Hz)
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
74.550
60.004
70.069
75.029
84.997
74.700
75.000
60.000
85.002
60.020
75.025
85.024
59.978
60.000
65.000
70.000
75.000
85.000 H-frequency
(kHz)
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
68.667
60.134
67.500
60.000
85.938
63.981
79.976
91.146
65.317
75.000
81.250
87.500
93.750
106.250 Clock
(MHz)
35.500
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
57.283
65.000
75.000
78.750
94.500
79.857
108.000
108.000
148.500
108.000
135.000
157.500
121.750
162.000
175.500
189.000
202.500
229.500Note
• Signals whose resolution exceeds the native resolution (1024  × 768 pixels) will be
compressed. For this reason, some information may be lost, or image quality may be
affected.
Specifications■ List of general specifications
Item Specification
Consumption Power TLP-X2500A: 300 W TLP-X3000A: 320 W
TLP-XC2500A: 300 W TLP-XC3000A: 320 W
Weight TLP-X2500A/X3000A: 2.8 kg
TLP-XC2500A/XC3000A: 4.0 kg
External Dimensions TLP-X2500A/X3000A: 288  × 92  × 247 mm (W  × H  × D)(including protruding parts)
TLP-XC2500A/XC3000A: 370.5  × 92  × 249 mm (W  × H  × D)
Cabinet material PC resin and PC+ABS resinConditions for usage
 environment
Temp: 5 °C to 35 °C; relative humidity: 30% to 70%
Display method 3-panel transmission
LCD Panel
P anel size
0.63 type
Drive system
TFT active matrix
Picture elements
786,432 pixels (1024H  × 768V)
Lens Zoom lens      F=1.6-1.88   f=18.6-22.3 mmLamp High-pressure mercury lamp
Projection screen size 33-300 inchesProjection distance 1.15-8.80 mSpeaker 1W (Mono)COMPUTER 1
Mini D sub 15 pin  RGB / Y/P
B/PR (dual use)
IN terminalCOMPUTER 2
Mini D sub 15 pin  RGB / Y/P
B/PR / MONITOR OUT (dual use)
IN terminalS-VIDEO terminal Mini DIN 4 pinAUDIO (L/R) terminal RCA Pin Jack  × 2VIDEO terminal RCA Pin JackA UDIO IN terminal 3.5mm dia. stereo mini-jackAUDIO OUT terminal 3.5mm dia. stereo mini-jack
CONTROL terminal
Mini DIN 8 pin (RS-232C)
■ Document camera specifications
(Models equipped with document camera)
Item Specification
Cameral lens F=3.0, f=9.6 mmFocus adjustment ManualZoom adjustment None (Adjust with the distance from the object)Image Pick-Up Device 3 million pixel 1/2 color CMOS SensorPixels QXGA (horizontal 2048  × vertical 1536)
Illumination High brightness LED LED illuminationNotes
• This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added
in the future.Connection terminal 
						

							59
Others
58
Specifications (Continued)
■CONTROL terminal●Pin assignment
7
6
8
5
43
21
Signal Name
RXD
CTS
DSR
GND
RTS
N.C
TXD
GND Pin No.
1
2
3
4
5
6
7
8Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
Signal ground
Mini DIN 8 pin connector
●Interface format
1Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:  1 bit
2Communication format STX (02h)  Command (3Byte)  ETX (03h)
Only 1 command valid per communication.
3Data format For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
4Replies Acknowledge ACK (06h)  CR (0Dh)  Data ...  Normally ended
ACK (06h)  ESC (1Bh) ...  Aborted
No acknowledge NAK (15h)
If commands are to be sent consecutively, wait for the response from the projector
before sending the next command.
●Main Commands
Item Command
Power onPONPower offPOFIcon display onMO0Icon display offMO1Auto setting (RGB input)PATStatus display onDON
Status display offDOFNote
•Contact your dealer for control cable and other commands.■Separately sold product
Replacement Lamp Model TLPLW11
■List of supported signals (Y/P
B/P
R signals)
Signal format fh(kHz) fv(Hz)
480i(525i)@60Hz15.73 59.94
480p(525p)@60Hz31.47 59.94
576i(625i)@50Hz15.63 50.00
576p(625p)@50Hz31.25 50.00
720p(750p)@60Hz45.00 60.00
720p(750p)@50Hz37.50 50.00
1080i(1125i)@60Hz33.75 60.00
1080i(1125i)@50Hz28.13 50.00
■List of supported signals (Video, S-Video signals)
Video mode fh(kHz) fv(Hz) fsc(MHz)
NTSC 15.73 60 3.58
PAL15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41
PAL-M 15.73 60 3.58
PAL-N 15.63 50 3.58
PAL-60 15.73 60 4.43
NTSC4.43 15.73 60 4.43
■Pin assignment of COMPUTER 1 IN, COMPUTER 2 IN &
MONITOR OUT terminals
11 156 1 5
10
Input Signal
•RGB input
RGB signals: 0.7V (p-p) 75 ΩHorizontal sync signal
:TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)
•Y/P
B/PR input
Y signal: 1.0V (p-p) 75 Ω
P
B/PR signals: 0.7V (p-p) 75 Ω Mini D sub 15 Pin connector
Pin Pin descriptionNo. During RGB input During Y/P
B/PR input
1Video signal (R) Color difference signal (P
R)
2Video signal (G) Luminance signal (Y)3Video signal (B) Color difference signal (P
B)
4GND∗5GND∗6GND (R) GND (P
R)
7GND (G) GND (Y)8GND (B) GND (P
B)
9N.C∗10 GND∗11 GND∗12 N.C∗13 Horizontal sync signal∗14 Vertical sync signal∗
15 N.C∗∗ Do not connect anything.