Toshiba Projector Tlp X10u User Manual

11
Before use
CONTENTS
Names of each part on the main unit
Continued
12
Control panel
Air exhaustInfrared remote sensorFront side
Right side
Rear side
Left side
Card slot
Anti-theft lock hole
Speaker
Air intake
Air intake
Foot adjuster 
release button
Foot adjuster
Zooming lever
Focusing ringAlso mounted on the front 
of the left side.
AC IN socket Lens cover
LensCarrying handle
Open to carry the projector.
TEMPLAMP ONBUSY FAN
ON/STANDBY
KEYSTONESET AUTO
AUTO
EXIT ENTER
MENUINPUT
VOL/ADJ.
TEMPLAMP...

12
Before use
CONTENTS
Names of each part on the main unit (continued)
To display the menu screen and/or select the 
operation on the menu screen.
Also use the selection button, ENTER button and 
EXIT button to operate the memory card.
Use the selection button and EXIT button to 
enlarge the image. 
TEMP indicator
BUSY indicator FAN indicator
LAMP indicator ON indicator INPUT button  ENTER button  Selection button
EXIT button VOL/ADJ buttons  AUTO KEYSTONE button 
AUTO SET button 
MENU button
ON/STANDBY...

13
Before use
CONTENTS
USBMONITOR OUT
COMPUTER IN 1(
Y/P
B/PR )
COMPUTER IN 2 CONTROL
S-VIDEO VIDEO
VIDEO IN
R - AUDIO - L
AUDIO
IN AUDIO
OUT
26
93
22
25
27
39
24
24
23
24
27
22
25
VIDEO jackTo enter video signal 
from a video equipment, etc.
AUDIO(L/R) jacksTo enter audio signal from a video equipment, etc.
CONTROL connector
(RS-232C Connector)To connect a computer to 
control the projector.
COMPUTER IN 1 connectorTo enter RGB signal from a computer, etc.
or component video signal (Y/P
B/PR Signal)...

14
Before use
CONTENTS
Names of each part on the remote control
INPUT button
MUTE button RESIZE buttons R-CLICK button
L-CLICK button Pointer control button
VOLUME/ADJUST buttons AUTO KEYSTONE button
AUTO SET button LASER button
PIP button
FREEZE button
CALL buttonON/STANDBY button Laser emission part
Remote control transmission part
To display the laser pointer by pointing the laser emission part 
toward the screen.
To set and/or adjust values on the menu.
To adjust volume when the menu is not...

15
Before use
CONTENTS
Loading batteriesNotes
Using batteries incorrectly can cause them to leak
or burst. Strictly observe the following.¥ Install the batteries with their + and Ð ends facing
correctly.
¥ Do not charge, heat, disassemble, or short the
batteries or throw them into a fire.
¥ Do not leave exhausted batteries in the remote
control.
¥ Do not mix different types of batteries or new and
old batteries.
¥ When you will not be using the remote control for
a prolonged period, take the batteries...

16
Before use
CONTENTS
Remote control operation
Point the remote control at the infrared remote sensor and press a button.
Notes
¥ The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the remote sensor.
¥ Operate the remote control from a position where the remote sensor is visible.
¥ Do not drop the remote control or otherwise jolt it.
¥ Keep the remote control out of locations with excessively high temperature or humidity.
¥ Do not get...

17
Installation and
connection
CONTENTS
Floor-mounted projector placement
Floor-mounted front projectionViewing a picture projected on the front of the
screen from a floor installation.
Floor-mounted rear projectionViewing a picture projected through the back of the
screen from a floor installation.
Viewer Translucent screen
Viewer There are two ways to place the floor-mounted projector. Perform the ÒProjection modeÓ setting on the menu screen for the projection
method. 
67
For the ceiling-mounted...

18
Installation and
connection
CONTENTS
Place the projector on a steady, level surface such as a table.To obtain proper screen projected, place the projector so that the projecting light hits the screen squarely.
Floor-mounted projector placement (continued)
Top view
Screen
Screen
a b
90¡
Side view
90¡Screen
a: Distance between the lens and
the screen (m)
b: Distance between the lens height
and the bottom of projection area
(cm)
Projection size
(inches)
25406080100150200250
b...

19
Installation and
connection
CONTENTS
Connect the power cord.¥ Insert one end in the AC IN socket on the projector.
¥ Insert the other end in a wall outlet.
Notes
¥ When the projector is moved from a cold location to a warm location, or when the ambient temperature in the projection room has risen suddenly,
moisture may condense on the lens or the internal optical section to blur the projected pictures. In such a case, leave the projector for an adequate time
(1 to 2 hours, depending on the roomÕs...

20
Installation and
connection
CONTENTS
Projector placement angle adjustment
Foot adjuster
release buttonFoot adjuster The tilt of the projector can be adjusted using the foot adjuster.
Lift the front of the projector until a tilt angle desired is
obtained and hold down the foot adjuster release button.The foot adjuster will stretch.
Release the button to lock in position.
Lift up
Lower Lift upLower
1
Turn the foot adjuster to make fine adjustment of the
height.Turn clockwise to lift up.
Turn...