Toshiba Projector Tlp T720 User Manual

21
20
Preparations
Switching operation modesOperation modes should be switched between projector operation and computer operation.
ON/
STANDBYAUTO
KEYSTONE
MUTE AUTO SET FREEZEINPUT R-CLICK PJ MODE LASERVOL.
+
VOL.-
MENU / ENTER
RESIZE
OFF
Notes•See page 52 for more information on operating a computer.
•For the remainder of this manual, buttons, including those on the control panel (main unit
side), are referred to as follows:
Selection button ⇒ 
 
 
 
; MENU/ENTER button ⇒ 
With the exception of...

23
22
Preparations
Before connection•Read the owner’s manual of the device to be connected to the projector.
•Some types of computer cannot be used connected to this projector.
Check for an RGB output terminal, supported signal 
p.69
, etc.
•Turn off the power of both devices before connection.
•The figure below is a sample connection. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Notes•COMPUTER terminals 1 and 2 function...

25
Operations
24
Connecting the power cord1
Insert the power cord connector into the AC IN socket of the projector.
2
Insert the power cord plug into a wall or other power outlet.
ON/S
TA N
DBYINPUT
MENU
AUTO
SET
FAN
TEMP
LAMP
ON VOL.
+
VOL.-AUTOKEYSTONE
FAN TEMP LAMP ON
Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.
 Turning the power on
Press the ON/STANDBY
button.The power turns on, and the
following 3...

27
Operations
26
INPUT R-CLICK PJ MODE LASERVOL.
+
VOL.-
MENU / ENTER
Preparations•Place the projector, and correctly connect all devices.
•To operate via the remote control, [PJ MODE] 
p.20
 must be
selected.
Press the PJ MODE button. The button lights up. This light
will go out 30 seconds after operations are complete. If
necessary, press the button again.
1
Turn on the power.Turn on the power, following the instructions in “Turning on the power” 
p.25
.
2
 Select language (When using for first...

29
Operations
28
ON/
STANDBYAUTO
KEYSTONEMUTE AUTO SET FREEZEINPUT R-CLICK PJ MODE LASERVOL.
+
VOL.-MENU / ENTER
RESIZE
OFF
ON/STANDBY
INPUTFAN TEMP LAMP ONVOL.
+
VOL.-
AUTOKEYSTONE
MENU
AUTO SET
Using handy featuresTo operate via the remote control’s 
 
 
 
 
 buttons, [PJ MODE] must be
selected. Press the PJ Mode button. The button lights up. This light will go out 30
seconds after operations are complete. If necessary, press the button again.
Using auto setting (Auto setting)
This function sets up...

31
Operations
30
ON/
STANDBYAUTO
KEYSTONEMUTE AUTO SET FREEZEINPUT R-CLICK PJ MODE LASERVOL.
+
VOL.-MENU / ENTER
RESIZE
OFF
Freezing the image (Freeze)
The image being projected can be made to be frozen. This function is to
be used to pause a video during a presentation, etc.
Press the remote control’s FREEZE button.The picture is paused. The Freeze function is released when
pressing the FREEZE button again.Notes•The 
 icon will appear while freeze is in effect.
•The freeze function can be used on the...

33
Operations
32
Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the 
 button twice.
When the 
 button is pressed once, the Setting display menu appears. Pressing
it again displays information 
p.53
. The table below shows what kind of information
is displayed. Press the button again to dismiss the display.
“Ye s”: displayed, “No”: not displayed
Item Description
Computer Y/P
B/PR
Video
PC Card CameraS-video
Input Input source name Yes...

35
Operations
34
Caution when using the wireless LAN functions
The Wireless LAN in this unit uses the 2.4 GHz waveband.  If there is a similar wireless
LAN in the area, or a wireless device using the 2.4 GHz waveband, or a microwave
oven, the communication efficiency of this apparatus will be reduced, and may become
unusable, but it is not a fault. If this happens, check an area away from the current
location that will not cause radio interference to medical, industrial and public
equipment, and change...

37
Operations
36
4
Select the screen image you wish the
projector to display.Select Desktop
The computer screen image is transmitted as-is.
Select application window
Select a running application (e.g. Microsoft
®
PowerPoint
®), and send that application’s window
only.
The desktop and a list of running applications are displayed.
Select the desired application from this list. (If the desired
application is not on the list, launch it. Note that if too many
applications are running, it will consume the...

39
Operations
38
5
Select the projector to be transmitted.A list of the MAC addresses of the wireless LAN
PC cards 
p.32
, p.60
 mounted on the projectors
that are available for transmission appears. If
projector name has been set up already, it is
shown instead of the MAC address. Select the
checkbox of the projector to be transmitted to from
this list. Then icon  is displayed on the
projector’s screen for few seconds.
It is possible to select up-to four projectors.
6
Click on the 
 button.
The selected...