Toshiba Projector Tlp T700 User Manual

							21
20
Preparations
■Switching operation modesOperation modes should be switched between projector operation and compu\
ter operation.
ON/
STANDBYAUTO
KEYSTONE
MUTE
AUTO 
SET FREEZE INPUT
R-CLICK
PJ MODE LASER
VOL.
+
VOL.-
MENU 
/ ENTER
RESIZEOFF
Notes•See page 51 for more information on operating a computer.
• For the remainder of this manual, buttons, including those on the contro\
l panel (main unit
side), are referred to as follows:
Selection button  ⇒ 
 
 
 
; MENU/ENTER button  ⇒ 
With the exception of operating a PC with the remote control 
p.51
, all buttons are
used in [PJ Mode].
Placement StylesAs shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the  placement style in the
default setting menu  
p.53
, in accordance with your needs.
Projection Distance and Screen SizeUse the figures, table, and formula below to determine the screen size a\
nd projection
distance. (Screen sizes are approximate values for full-size picture an\
d no keystone
adjustment)
90°
ON/STANDBYINPUTFA
NT EMP LAMP ON VOL.+VOL.-AUTOKEYSTONEMENUAUTO
 SET
a
90°
USBCOMPUTER
( Y, PB/PR )S-VIDEO
VIDEOVIDEOR - AUDIO - LA UDIOMONITORCONTROL12
Switching the remote control operation mode.Pressing this button toggles the mode.
When this button is lit, the remote control is in  [PJ Mode]
(Projector operation mode).
If no operations are made for 30 seconds, this light goes
out, and the remote switches back to  [PC Mode] (Computer
operation mode).[PJ Mode] :Functions as a select button.
If no menu is displayed, adjusts volume.
[PC Mode] :Functions as a mouse pointer control.[PJ Mode] :Ends memory card slide display.
[PC Mode] :Functions as a down button. Used to go
forward on Microsoft
® PowerPoint
® slides, etc.
[PJ Mode] :Begins memory card slide display.
[PC Mode] :Functions as an up button. Used to go back on
Microsoft
® PowerPoint
® slides, etc.
[PJ Mode] :Functions as a MENU/ENTER button.
[PC Mode] :Functions as the right mouse button (R-CLIK).Pressing displays a laser pointer, regardless of the mode.Pressing one of these buttons automatically sets the remote
control to  [PJ Mode] .
If no operations are made for 30 seconds, and the remote
switches back to  [PC Mode].The L-CLICK (left click) button on the back of the remote
control functions when in  [PC Mode].
Preparing and using the remote control (Continued)
PlacementFloor-mounted front projection
Floor-mounted rear projection
Ceiling-mounted front projection Ceiling-mounted rear projection
 CAUTION
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when
placing the unit.
• If you wish to mount the projector on the ceiling, be sure to ask your d\
ealer to do so.
Mounting the projector on a ceiling requires special ceiling brackets (\
sold separately)
and specialized knowledge. Improper mounting could cause the projector t\
o fall,
resulting in an accident.
a is the distance (m) between the lens and
the screen, and corresponds to a range of
1.50 m to 11.74 m.Screen
As seen from above
Lens center
As seen from the side
a (min length) =  projection size (inches) – 1.7971
25.395a (max length) =  projection size (inches) – 1.4258
20.148
screen projection distance a(m)
min length max lengthsize (cm) (zooming max) (zooming min)32 (81) — 1.5040 (102) 1.50 1.9160 (152) 2.29 2.9180 (203) 3.08 3.90100 (254) 3.87 4.89150 (381) 5.84 7.37200 (508) 7.80 9.86250 (635) 9.77 —
300 (762) 11.74 —
USBCOMPUTER
( Y, PB/PR  )S-VIDE
O
VIDEOVIDEOR  - AUDIO - LAUDIOM ONITORCONTROL1
2
USBCOMPUTER
( Y, PB/PR )S-VIDEO
VIDEOVIDEOR - AUDIO -  LAUDIOMONITORCONTROL12 
						

							23
22
Preparations
Before connection•Read the owner’s manual of the device to be connected to the projector.
•Some types of computer cannot be used connected to this projector.
Check for an RGB output terminal, supported signal 
p.68
, etc.
•Turn off the power of both devices before connection.
•The figure below is a sample connection. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Notes•COMPUTER terminals 1 and 2 function identically.
•The AUDIO terminal doubles for devices connected to COMPUTER terminals 1 and 2.Connection
USB
COMPUTER(
Y/PB/PR )
S-VIDEO VIDEO
VIDEO
R - AUDIO - L
AUDIOMONITORCONTROL
12
p.70
p.51Computer Desktop computer
To audio output
To USB terminal
USB cable
Audio cable
(for computer)
(supplied)To RGB
output
Control cable
To RS-232C terminalComputer (for control)
RGB cable
(supplied)
To Y/C
B/CR
output
Green (Y)
Blue (C
B),
Red (CR) Yellow
(to video output)
To audio
output
White (L)
Red (R)
VCR
S-Video cable
(not supplied)
AV cable
(supplied)
To S-Video
outputTo audio
output
White (L)
Red (R)To audio
outputTo RGB
output
Monitor cable
Mini D-sub 15P-BNC
(not supplied)
Audio cable
(not supplied)
DVD player
Conversion
adapter
BNC-pin
(not supplied)
How to use the PC card slotPlease read this chapter if the model you purchased includes a PC card slot.
The attached wireless LAN PC card enables you to connect the projector wirelessly with a
personal computer that supports IEEE802.11b based wireless LAN. Please note that
communication between all the computers based on IEEE802.11b and this projector is not
guaranteed. 
p.33
 You can also use a commercially available memory card to project JPEG
image files using this projector. 
p.40
 Please follow the steps below when removing or
mounting a PC card.
Mounting a PC cardq Remove the PC card slot cover.
Press lightly on the circle (“O”) while
sliding the cover in the direction of the
arrow.
Card slot cover
wInsert the PC card.
After making sure of the card
orientation, press it in firmly until it
stops.
PC Card
e Replace the PC card slot cover.
Replace the PC card slot cover to keep
dust from entering.
Removing a PC cardqLook at CARD indicator.
If it is off, proceed to step r.
UNMOUNT button
CARD indicator
wPress the UNMOUNT button.
Begins processing for PC card removal
eWait until CARD indicator goes
out.
Never remove the PC card while lit.
Doing so could damage the PC card or
corrupt your data.
rPress the Eject button.The Eject button is a bit stiff, so press
firmly while supporting the projector.
Be careful to avoid injury when doing
so.
Eject button
If CARD indicator turns redPress the RESET switch with a thin pin or
similar implement (it is at the bottom of a
recess).
RESET switch CARD indicator 
						

							25
Operations
24
Connecting the power cord1
Insert the power cord connector into the AC IN socket of the projector.
2
Insert the power cord plug into a wall or other power outlet.
ON/STANDBYINPUT
MENU
AUTO
SET
FAN
TEMP
LAMP
ON VOL.
+
VOL.-AUTOK
E
Y
S
T
O
N
E
FAN TEMP LAMP ON
Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.

 Turning the power on
Press the ON/STANDBY
button.The power turns on, and the
following 3 green indicators light:
ON, LAMP, and FAN. After a
moment, the start-up screen
appears. CAUTION
• Do not look into the lens during operation. Doing so could damage your vision.
• Do not block the air intake or exhaust. Doing so could cause a fire due to internal
overheating.
• Do not place your hands, face, or other objects near the air exhaust. Doing so could
cause burns, deform/break the object.Notes• The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu 
p.54
.
• The first time you use the projector after purchase, after the start-up screen disappears,
the Language menu is displayed 
p.27
.
Turning the power on and off
When the power cord is plugged in, the following three
green indicators will come on for several seconds: ON,
TEMP, and LAMP. Next, the ON indicator will change to
orange, indicating standby mode.
(Do not perform any operations while the 3 green
indicators are lit.)
(Supplied) Power cord connector
Start-up screen
ON/
STANDBYAUTO
KEYSTONEMUTE AUTO SET FREEZEINPUT R-CLICK PJ MODE LASER
VOL.+
VOL.-MENU / ENTER
RESIZE
OFF
ON/STANDBY
INPUTFAN TEMP LAMP ONVOL.
+
VOL.-
AUTOKEYSTONE
MENU
AUTO SETControl panelRemote
Control
Please read this chapter if the model you purchased includes a PC card slot.
If you will use the supplied wireless LAN PC card function, install the application on the
supplied CD-ROM onto your computer.
System Requirements
Supported OSs: Windows
® 98SE, Windows
® Me, Windows
® 2000, Windows
® XP
CPU: Pentium III 750 MHz or higher recommended
RAM: 256 MB or more recommended
Screen area (resolution): 1024 by 768 pixels recommended

Application Types and Major Functions
Wireless utilityThis application is used for wireless connections. Use it to send the images from the
computer’s screen to your projector, and display on the screen.Projector Configuration ToolUse to modify wireless LAN and TCP/IP settings.JPEG Conversion ToolUse to convert JPEG and other files into a format that can be displayed as a slide show
using a memory PC card.

How to install
In the supplied CD-ROM, select the Applications folder, and run setup.exe. Follow the
instructions on your computer screen.
If you are using Windows
® XP or Windows
® 2000, during installation a dialog box may
appear with the following message: has not passed Windows Logo to verify its
compability with Windows XP (2000). Click “Continue Anyway”, and continue with the
installation.
When installation is finished, the following shortcuts will appear on your computer’s
desktop:
Wireless Utility →Operations 
p.35
Projector Configuration Tool →
Operations 
p.59
JPEG Conversion Tool →
Operations 
p.61

How to uninstall
Select [Start Menu] → [Settings] → [Control Panel] → [Add/Remove Programs],
and remove Toshiba Data Projector from currently installed programs.
Installing the applications 
						

							27
Operations
26
INPUT R-CLICK PJ MODE LASERVO L.
+
VOL.-
MENU / ENTER
Preparations•Place the projector, and correctly connect all devices.
•To operate via the remote control, [PJ MODE] 
p.20
 must be
selected.
Press the PJ MODE button. The button lights up. This light
will go out 30 seconds after operations are complete. If
necessary, press the button again.
1
Turn on the power.Turn on the power, following the instructions in “Turning on the power” 
p.25
.
2
 Select language (When using for first time).When the projector is used for the first time after purchase, a message is displayed on
the screen, and the language menu appears. The default language is English.
(If the screen focus is not on the menu, adjust according to step 
6.)
qUse the 
 
 buttons to select the desired
language, and press the 
 button.
A message displays the selected language.
wPress the 
 button to apply.
Notes•After the first time the projector is turned on, the Language menu does not appear
upon startup. However, from the Reset menu 
p.55
 select “Reset all” to display the
Language menu the next time the projector is turned on.
•The language can also be set via the Display setting menu 
p.54
.
•This owner’s manual assumes that English has been selected.
3
Place connected device(s) in operating status.Turn on and boot up connected computers and other devices.
4
Select input.qPress the INPUT button.
A list of inputs appears on the screen.
wUse the 
 
 buttons to select the desired
input, and press the 
 button.
The picture for the selected input is projected.
Basic operations
Remote Control
[PJ MODE]
Lights up
English
Français
Português Deutsch
Italiano
Español
................
..............
..............
................
...............
..........
...................
.......
.......
...................
English
French
German
Italian
Spanish
Portuguese
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
Computer (1)
Y/P
B/PR(1)
Computer (2)
Y/P
B/PR(2)
Video
S-video
PC Card
Camera
Turning the power on and off (Continued)Turning the power off1
Press the ON/STANDBY button.A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button again.The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
When cooling lamp During internal cooling After cooling complete
FAN TEMP LAMP ON
FAN TEMP LAMP ON
AFAN TEMP LAMP ON
B
C
(Green) (Green) (Orange)
Flashing(Green) (Off) (Orange)(Off) (Off) (Orange)
A
During cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on. In addition, unplugging the power cord in this state will shorten
the life of the lamp.
B
After the LAMP indicator goes off, the cooling fan continues to operate for a
short while, in order to expel excess internal heat. If you are in a hurry, there is
no problem with unplugging the power cord in this state.
C
In standby
Note•The projector consumes about 6W of power in standby (models equipped with PC card
slot consume about 18W). We recommend that you unplug the power cord if you will not
be using the projector for an extended period.PRECAUTIONS•Before unplugging the power cord, make sure that the LAMP indicator is off. Unplugging
the power cord and cutting off the power while the projector is running or being cooled
will shorten the life of the lamp. However, please unplug the power cord if the
projector locks up or acts abnormally.
•If the power cord was unplugged before cooling was complete, give the lamp sufficient
time to cool before plugging it back in. If the lamp overheats it may fail to light, and its
lifetime will be shortened.
LCD Panels
LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the
following precautions.
•In order to extend the lifetime of the LCD panel, always turn off the power when not in
use, and make sure that the lamp is off. Keeping the lamp off is also very effective at
saving electricity.
•If the air filter becomes dirty and clogged, the projector’s internal temperature will rise,
shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter
from time to time 
p.56
, and replace it periodically. Contact the store where you
purchased your projector, or your local Service Station for replacement air filters. 
						

							29
Operations
28
ON/
STANDBYAUTO
KEYSTONEMUTE AUTO SET FREEZEINPUT R-CLICK PJ MODE LASERVOL .
+
VOL .-MENU / ENTER
RESIZE
OFF
ON/STANDBY
INPUTFAN TEMP LAMP ONVOL.
+
VOL.-
AU TOKEYSTONE
MENU
AUTO SET
Using handy featuresTo operate via the remote control’s 
 
 
 
 
 buttons, [PJ MODE] must be
selected. Press the PJ Mode button. The button lights up. This light will go out 30
seconds after operations are complete. If necessary, press the button again.

Using auto setting (Auto setting)
This function sets up the projector to the optimum state for
each type of the input signal by using simple operations.1
Press the AUTO SET button.The Auto setting menu appears.
2
Press the AUTO SET button again.The menu item is automatically adjusted/set.
For computer input, the 
 icon will appear during
processing.
Note•Auto adjustment/setting may not be performed correctly for input signals other than
those supported by the projector 
p.68
, p.69
.
Manual adjustment and setting
The menu items vary according to the input type, as shown in the table below.
Use the 
 
 
 
 
 buttons to adjust the items in the table below, then press
the 
 button when you are finished. The menu disappears.
Control panelRemote
Control
PhaseAdjust with           to eliminate flicker.
Frequency
Adjust with            to eliminate periodic patterns and 
flickering when many vertical lines appear in the screen.
H-positionMove left           Move right
V-positionMove up            Move down
PhaseAdjust with           to eliminate flicker. Input Item
Description
Computer (1)
Computer (2)
Select Item Select Item
Signal format
[     : Enter to setting mode]    [          : Select one 
of the following]    [Apply:     ]
480i(525i)@60Hz/480p(525p)@60Hz/
 576i(625i)@50Hz/576p(625p)@50Hz/
 720p(750p)@60Hz/720p(750p)@50Hz/
 1080i(1125i)@60Hz/1080i(1125i)@50Hz/
 1035i(1125i)@60Hz/1152i(1250i)@50Hz
Video mode[     : Enter to setting mode]    [          : Select one 
of the following]    [Apply:     ]
 
NTSC/PAL/SECAM/PAL-N/PAL-M/PAL60/NTSC4.43
Shutter speedSet to local line frequency: 50Hz           60Hz Y/P
B/PR(1)
Y/P
B/PR(2)
Video
S-video
Camera
1
2
312
Basic operations (Continued)5
Projector placement angle adjustmentsThe placement angle and the height of the projected image can be adjusted by the foot
adjuster.qLift up the front of the projector until
it is at the desired angle, then press
the foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
wTurn the foot adjuster to fine-tune
the angle.
eTo adjust the horizontal angle, use
the tilt adjuster.
To stow the foot adjuster, hold up the projector while pressing the foot adjuster
release button, then slowly lower the projector will the button depressed.
6
Adjusting the picture size and focusqUse the zooming lever to adjust the screen
size.
wUse the focusing ring to adjust the focus.
7
Adjusting the volume with the 
 
 buttons
The speaker volume can be adjusted when an audio signal is being input.Notes•Note that the lamp characteristics may rarely cause the brightness to fluctuate slightly.
•A lamp is consumable supplies.
If used for extended periods, images will appear dark, and the lamp could burn out.  This
is characteristic of a lamp, and is not malfunction. (The lifetime of the lamp depends on
conditions of use.)
•The LCD panel is made using extremely advanced technology, but there may be black
spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.
Please note that these are not malfunctions.
•Although this projector supports a wide range of RGB signals 
p.68
, any resolutions not
supported by the model (XGA or SVGA, depending on the model) will be expanded or
shrunk, which will affect image quality slightly. To view high-quality images, it is
recommended that the computer’s external output should be set to the projector’s
resolution.
•With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
•If a signal not supported by the projector is input, the 
 icon will appear.
•If a no signal is being input from the connected device, the 
 icon will appear.
•If an unavailable operation button is pressed, the 
 icon will appear. 
						

							31
Operations
30
ON/
STANDBYAUTO
KEYSTONEMUTE
AU
TO SET FREEZE INPUT
R-CLICK
PJ MODE LASER
V
OL.
+
VOL.-MENU  / ENTER
RESIZEOFF
■ Freezing the image (Freeze)
The image being projected can be made to be frozen. This function is to
be used to pause a video during a presentation, etc.
Press the remote control’s FREEZE button.The picture is paused. The Freeze function is released when
pressing the FREEZE button again.Notes•The 
 icon will appear while freeze is in effect.
• The freeze function can be used on the resize function. Other
operations will release the freeze.
• Even if an image is frozen on the projector, it is still changing on the video or other
equipment.
■ Enlarging the picture size (Resize)
The image being projected can be enlarged.1
Press the remote control’s RESIZE 
 button.
The enlargement ratio is increased each time the RESIZE 
  button is pressed.
While the button is pushed, the image continues increasing to a limit.
2
To  decrease the enlargement ratio, press the remote control’s RESIZE
 button.
The enlargement ratio is decreased each time the RESIZE 
  button is pressed.
(The image cannot be shrunk to less than its original size.)
3
Press and hold down the 
 
 
 
 buttons to
move the enlarged area.
4
Press the OFF button to undo the resize.The resize is released, and the image returns to its original size.Notes• The 
 icon will appear while resize is in effect.
• An enlarged image can be frozen using the FREEZE button. The resize function on
a frozen image can also be used.
• Operations other than freeze will release the resize.
• Since the enlargement is performed using digital processing, enlarging t\
he image
will cause it to appear jagged.
• Rarely, the picture could become garbled while the enlarged area is being move\
d.
Remote
Control
ON/
STANDBY AUTO
KEYSTONEMUTE
AU
TO SET FREEZE INPUT
R-CLICK
PJ MODE LASER
V
OL.
+
VOL.-MENU  / ENTER
RESIZEOFFRemote
Control
q
w
r e
ON/
STANDBY AUTO
KEYSTONEMUTE
AU
TO SET FREEZE INPUT
R-CLICK
PJ MODE LASER
V
OL.
+
VOL.-MENU  / ENTER
RESIZEOFF
ON/STANDBY
INPUTFA N TEMP LAMP ON V
OL.
+
VOL.-
AUTOKEYSTONE
MENU
AUTO  SET
ON/
STANDBYAUTO
KEYSTONEMUTE
AU
TO SET FREEZE INPUT
R-CLICK
PJ MODE LASER
V
OL.
+
VOL.-MENU  / ENTER
RESIZEOFF
Using handy features (Continued)■ Correcting the keystone distortion (Keystone)
When the foot adjuster 
p.28
 is used to change the
projection angle, the picture will undergo keystone (trap-
ezoidal) distortion.
This projector is capable of correcting this keystone
distortion.
Before correction After correction
US
BC
O M P
U T
E R
( Y,
PB/PR  )S
-
V I
D E
O
V I
D EOV
I
D EOR
 -
 A U DI
O  
-
 LA U
D I
OM
ON
IT
O
RCO N
TR
O L1
2
q
Press the AUTO KEYSTONE button.
The Keystone menu appears.
wPress the AUTO KEYSTONE button again.
The keystone distortion is automatically corrected. The 
 icon will appear during
processing.
● Manual adjustment
Use the 
 
 buttons for keystone adjustment. When the adjustment is finished,
press the   button. The menu disappears.
Notes• Depending on the amount of keystone adjustment and the contents of image\
s,
some information may be lost, or the picture quality may suffer.
• Keystone adjustment will not change the shape of the menus.
■ Cutting off the picture and sound temporarily (Mute)
When you want to temporarily project the images of another projector,
overhead projector, etc., this projector’s images and sound can be turned
off.
Press the remote control’s MUTE button.The picture and sound are cut off. The Mute function is released
when pressing the MUTE button again.
The 
 icon will appear while mute is in effect.
Control panel Remote
Control
Remote
Control
Keystone
Shrink screen bottom            Shrink screen top
Item Description 
						

							33
Operations
32

Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the 
 button twice.
When the 
 button is pressed once, the Setting display menu appears. Pressing
it again displays information 
p.52
. The table below shows what kind of information
is displayed. Press the button again to dismiss the display.
“Ye s”: displayed, “No”: not displayed
Item Description
Computer Y/P
B/PR
Video
PC Card CameraS-video
Input Input source name Yes Yes Yes Yes YesRGB signal mode
RGB input mode 
[Note 1]
YesNoNoNoNo
H-resolution
Horizontal resolution (in bits)
YesNoNoNoNo
V-resolution
Vertical resolution (in bits)
YesNoNoNoNo
H-frequency
Horizontal sync frequency
YesNoNoNoNo
V-frequency
Vertical sync frequency 
[Note 2]
YesNoNoNoNo
Sync
Sync signal polarity 
[Note 3]
YesNoNoNoNo
Signal format Y/P
B/PR signal format No Yes No No No
Video mode
Color method of video signal
No No Yes No No
Card type PC card type No No No Yes No
Shutter speed
Shutter speed of document
No No No No Yes
imaging camera
Lamp time Time of lamp use 
[Note 4]
Yes Yes Yes Yes Yes
Version Firmware version 
[Note 5]
Yes Yes Yes Yes Yes
MAC address See page 59 
p.59
No No No
Ye s [Note 6]
No
SSID See page 60 
p.60
No No No
Ye s [Note 6]
No
DHCP See page 60 
p.60
No No No
Ye s [Note 6]
No
IP address See page 60 
p.60
No No No
Ye s [Note 6]
No
Subnet mask See page 60 
p.60
No No No
Ye s [Note 6]
No
Gateway See page 60 
p.60
No No No
Ye s [Note 6]
No
Notes
1: The mode of supported RGB signals 
p.68
 is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the time displayed approaches 2,000
hours, consult with a store about getting a TLPLW1 replacement lamp (sold separately)
prepared.
5: [Version] shows the version of the projector’s internal control program. This version is
referred to for customer service, etc.
6: Displayed when wireless LAN PC card is being used.
Notes•The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
•Conducting another operation while information is being displayed dismisses the
display.
Using handy features (Continued)
Using the wireless LAN PC cardPlease read this chapter if the model you purchased includes a PC card slot.
Functions
The following functions are available via wireless communications, when the wireless
LAN PC card and dedicated Wireless Utility software 
p.24
 included with this projector
are used.
Note: Toshiba does not guarantee operation if a wireless LAN PC card other than
the one supplied with this product is used.
1) Displaying a computer’s screen via the projector
The computer’s desktop screen can be sent, as well as the screens of a variety of
software applications, to the projector for display.
2) Displaying an image saved on a computer via the projector
JPEG files can be sent to the projector for display.
3) Sending images taken with the projector’s document camera to a computer
This function is for models equipped with document camera.
See “Sending the camera’s images to a computer” 
p.48
 for details.
4) Operating the projector by means of a computer
Some of the same functions available from the remote control can be performed.

Communication mode
This projector supports both Ad-hoc and Infrastructure Communication modes.
Ad-Hoc Communication Mode
This is transmission mode to communicate
between wireless LAN equipment.
Wireless communication can be performed via
the simple configurations.
This function can only be used if the projector is
in range of the computer’s wireless signals.
For security reason, confirm the specifications of your computer for the distance that
the radio wave can reach. The coverage of this projector may vary, depending on the
computer and the surrounding environment. When tested with a PC manufactured by
Toshiba with built-in wireless LAN system, the coverage is approximately 60 m.
This figure is not guaranteed and should be considered as merely a guideline.
Infrastructure Communication Mode
A mixed wireless and wired LAN can be created
via access points. Connecting to the rest of the
world via a wired LAN or the Internet generally
requires a high level of security.
Use the appropriate transmission mode for your network environment. The instructions
in this owner’s manual assume that you will be using a simple ad-hoc communication
mode setup.Access pointTo LAN,
Internet, etc.
Hub
O
N
/
S
T
A
N
D
B
YINPUT
MENUA
U
T
O
S
E
T
F
A
NT
E
M
PL
A
M
PO
N V
O
L
.+V
O
L
.-AUTOKEYSTONE
O
N
/
S
T
A
N
D
B
YINPUT
MENUA
U
T
O
S
E
T
F
A
NT
E
M
PL
A
M
PO
N V
O
L
.+V
O
L
.-AUTOKEYSTONE 
						

							35
Operations
34
■Displaying a computer’s screen via the projector1
Launch the Wireless Utility software
application.When the  Wireless Utility  launches, the  Screen
image  transmission mode window appears on the
computer screen.
To  switch to the  Screen image  transmission mode
window from another mode ( File or Document
camera ), click on the  Screen Image  icon 
.
2 Select Transmission mode.Click on  Update automatically  or  Update manually . See step 
6 for the meanings of
Update automatically  and  Update manually .
3
Click on the Advanced button.The Advanced Settings  dialog appears. Set the
dialog as shown below, as necessary.
• Interruption
Select the  No Interruptions  checkbox to prevent
other computer from sending interrupts to the
projector during your transmission.
• Mode
Selecting  High quality  improves the quality of the
projected image, but lowers communication speed.
Selecting  High speed  has the opposite effect.
•W indow
Select the  Place in Tasktray at the start of
transmission  checkbox to iconify the  Wireless
Utility  and place it in the computer’s tasktray
when transmission initiated.
To  display the window, double click on this icon, or
right click and select  Open from the popup menu.
T ransmission can be started and stopped from this
popup menu in accordance with the preceding
instructions, without displaying the  Wireless
utility  window.
■ Preparation●Mount the supplied wireless LAN PC card into the projector, and select
PC card input
Referring to “Mounting a PC card,” 
p.23
 mount the supplied wireless LAN PC card, then
select PC card input in accordance with “Select input” 
p.27
.
● Projector settings
The factory settings can be used as-is. If necessary, conduct the following settings,
referring to “How to use the menu” 
p.52
 and “The PC card setting menu” 
p.54
.
• [Communication mode]:
Your projector is set to Ad-Hoc in the factory. See  “How to Use the Projector
Configuration Tool”  
p.59
 if you would like to set the mode to  Infrastructure. This
menu item is used only for channel confirmation and the mode change from\
Infrastructure  to Ad-Hoc .
• [Channel]
This item cannot be changed currently. This is function for the future.
• [Encryption]
Set the security encryption level. The higher the number of bits, the stronger the
encryption, and hence the harder it will be for a third party to deciphe\
r your
communications. However, setting higher encryption levels will slow down
communication speed.
• [Key]
The key must be set for any  encryption setting other than  None. [64-bit ] sets the  key
length to 5 characters, [ 128-bit] to 13.
• [Projector name]
This can be used to identify projectors when communicating with multiple\
 projectors, or
if there is a possibility that another person who is out of communicatio\
n range will be
using the same projector. It is recommended this is set to prevent wrong transmission.
● Installing the applications
Install the applications on your computer, in accordance with  “Installing the
applications”  
p.24
.
●Computer settings
Refer to instruction manuals of your computer or wireless LAN PC card to\
 perform the
following settings.
• Select  Ad-Hoc  (for some PC cards, this is  Peer-to-Peer Group).
• Set the  Channel  to channel assigned to the projector (in factory reset mode, this is s\
et
to 10). (For some computers, you cannot set the channel in Ad-Hoc mode. For this
case, use infrastructure communication mode.)
• Set  SSID  (For some types of PC card, use  Network Name instead) as the same as
projector’s  SSID (at factory shipment, this is set to  DPJ).
• If  Encryption  and Key are set on the projector, set to the same values.
Using the wireless LAN PC card (Continued) 
						

							37
Operations
36


Displaying a JPEG image saved on a computer via the projector
1
Launch the Wireless Utility software application.The Screen image transmission mode window appears on the computer’s screen.
2
Click on the File icon 
.
The Wireless Utility window
changes to File transmission
mode.
3
Click on the Browse button, and select the
file to send.Clicking on the Browse button displays the Open
dialog box. Select the file to send, then click on the
Open button.
The selected file is added to the pull-down list in the
Wireless Utility’s Transmission File field.
4
Select the file to be sent from the pull-down
list of the Transmission File field.Click on the Transmission File field’s 
 button
to display the pull-down list. Select the file to be
sent from this list.
A thumbnail of the selected file appears in the
Preview box. The file displayed here will be
transmitted.
Step 
3 can be skipped.
The way that drag and drop the file to be sent from the desktop or Windows Explorer
into the Preview box is also available. In this case as well, the selected file is added to
the file pull-down list Transmission File field’s.
4
Select the screen image you wish the
projector to display.Select Desktop
The computer screen image is transmitted as-is.
Select application window
Select a running application (e.g. Microsoft
®
PowerPoint
®), and send that application’s window
only.
The desktop and a list of running applications are displayed.
Select the desired application from this list. (If the desired
application is not on the list, launch it. Note that if too many
applications are running, it will consume the computer’s
resources, which could slow communication speed.)
5
Select the projector to be transmitted.A list of the MAC addresses of the wireless LAN
PC cards 
p.32
, p.59
 mounted on the projectors
that are available for transmission appears. (When
a projector name is set, that name appears instead
of MAC address.) Select the checkbox of the
projector you wish to transmit to from this list. Then
icon 
 is displayed on the projector’s screen for
few seconds.
It is possible to select up-to four projectors.
6
Click on the 
 button.
When “Update automatically” is selected in step 
2
Screen images are sent consecutively after the 
 button is clicked.
When “Update manually” is selected in step 
2
A single screen image is sent when the 
 button is clicked.
7
To halt transmission from Update automatically, click on the button.If the Wireless Utility icon has been placed in the tasktray, double click on the icon to
display the window, then halt transmission, or right click on the icon, and halt
transmission.Notes• It may not be possible to transmit the images from movie player or other video
applications.
• If using consecutive transmission, the transmitted image refresh rate depends on the
performance of the computer you are using.
• The projector screen may have a few differences from the computer screen.
• It is not possible to transmit to a projector that is already receiving from another
computer.
• If you selected application window in step 
4, if that application is not active (in use), the
image may not be correctly displayed by the projector.
Using the wireless LAN PC card (Continued) 
						

							39
Operations
38
3
Select the projector to be operated.In the Remote Control  window, click on the 
 button, and
select the desired projector from the pull-down list.
Only one projector can be selected. (It is not possible to operate
multiple projectors.)
Then icon 
  is displayed on the projector’s screen for few
seconds.
4
Click on the Remote Control window’s buttons.The function of each button and box is as follows:
Power On :Turns projector power on.
Power Off :Turns projector power off.
Note, however, that if  Standby mode is set to  Economy  from the
Default setting  menu 
p.53
, it is not possible to switch from  off to  on .
(Standby power consumption during  Economy is about 6W.)
Input  (box) : Click on the 
 button, and select the desired input from the pull-down
list.
Mute : Cuts off picture and sound. Click again to restore picture and sound.
Freeze : The picture is paused. Click again to release the freeze function.
V olume (+/–)  :Adjusting sound volume.
Resize (+/–)  : Displays expanded image.
↑
↑ ↑
↑
↑ /
↓
↓ ↓
↓
↓ /
←
← ←
←
← /
→
→ →
→
→ : Moves expanded image.
Resize Off :Restores picture to its original size.
5
To quit, click on the 
 button on the Remote Control window.
Performing this does not close the  Wireless Utility  window.
To exit both the  Wireless Utility  and the  Remote Control , click on the 
 button on
the  Wireless Utility  window.
5
Select the projector to be transmitted.A  list of the MAC addresses of the wireless LAN
PC cards 
p.32
, p.59
 mounted on the projectors
that are available for transmission appears. If
projector name has been set up already, it is
shown instead of the MAC address. Select the
checkbox of the projector to be transmitted to from
this list. Then icon   is displayed on the
projector’s screen for few seconds.
It is possible to select up-to four projectors.
6
Click on the 
  button.
The selected file’s image is displayed by the projector.Note• Only one file can be sent at a time. To send another file, repeat steps 
4 and 
6.
■ Operating the projector
This function can be used with any projector input.
Note, however, that this will not function with a memory PC card.
1
Launch the Wireless Utility software application.The  Screen Image transmission mode  window appears on the computer’s screen.
2
Click on the Remote Control
button 
.
The  Remote Control  window
appears.
As the  Wireless Utility  window is still
displayed, you can operate the
projector via the  Remote Control
window, while using the  Wireless
Utility ’s functions.
While it is possible to use this function merely to operate the projecto\
r, closing the
W ireless Utility  also closes the  Remote Control  window.
Using the wireless LAN PC card (Continued)