Toshiba Projector Tlp T501 User Manual

							61
60
Others
How to use the supplied software (Continued)5
Configure the projector.[Channel]
This item cannot be changed currently.
[Encryption]
Click on the 
 button to select [Off], [64 bit], or [128 bit].
[Key]
This accepts input if Encryption is set to other than Off (input is required). Input a
value from the keyboard.
[Communication mode]
Select Infrastructure by clicking the 
 button.
[SSID]
This is an ID code for connecting to specific individuals over a wireless LAN. This field
accepts input when set to Infrastructure Transmission Mode. Set the SSID to the
same value as the access point. In factory shipment, this is set to DPJ.
[Projector name]
It is recommended this is set to prevent wrong transmission. 
p.34
[DHCP]
Specify by clicking the 
 button. If this is set to Used, the IP Address, Subnet
Mask, and Gateway below are set automatically.
Consult with a network administrator for the settings below, if DHCP is not used.
[IP Address]
An IP (Internet Protocol) is a data communication protocol. The delivery destination is
an IP address.
[Subnet Mask]
This value is to set a limit on the range of IP addresses, and set up a number of sub-
networks.
[Gateway]
This is a relay point for connecting different types of network.
6
Press the Settings button.Communication begins, and the computer configures the projector. When setup is
finished, a message appears in the window telling you than setup is complete.
From the File menu, select Save As..., and save the settings file on the computer.

How to use the JPEG Conversion Tool
The JPEG Conversion Tool converts JPEG files not supported by the projector, image
files in other formats, Microsoft
® PowerPoint
® files, and the like into JPEG files
supported by the projector. The JPEG files converted with this tool can be displayed by
sending them using the wireless LAN PC card p.37
, or saving them on a memory PC
card 
p.41
.
Launching the JPEG Conversion Tool
The window shown in the figure to the right appears on the computer
screen.
Drag the Image Quality Settings slider to the left or right to set the
image quality of the file after conversion. Lower values create smaller
files, but lower the image quality. (It is not possible to restore the
quality of an image after it has been lowered.)
Converting an image file
This converts JPEG files using compression formats not supported by the projector,
Windows
® metafiles (wmf), and bitmapped files (bmp) into JPEG files.
(1) In the Conversion Method field, select Converting image
file. (Status on launch)
(2) In the File settings field, click on the Browse button for
Original Image File Name.
The Open dialog box appears.
(3) In the Open dialog box:
(a) Specify the location of the file to be converted; and
(b) In the Files of  Type field, click on the 
 button to
select the file format. A list of files of that format appear
in the Open dialog box.
(4) In the Open dialog box, select the file to convert,
then click on the Open button.
(5) In the JPEG Conversion Tool window, in the File
settings field, select Browse for File name after
conversion. The Save As dialog box appears.
(6) In the Save As dialog box:
(a) Specify the location in which to save the
converted file;
(b) Enter a file name of up to 8 characters in the
File Name field; and
(c) Press the Save button.
(7) (a) In the JPEG Conversion Tool, click on the Conversion button.
(b) A confirmation dialog box opens. Click Ye s.
The computer converts the file. When it finishes a message
appears informing you that a JPEG file has been created.
(1)
(2)
(5)
(7)-(a)(1)
(2)
(5)
(7)-(a)
(3)-(b) (3)-(b) (3)-(a)
(4)(6)-(b) (6)-(c) (6)-(a)
(7)-(b) (7)-(b) 
						

							63
62
Others
Converting files created with Microsoft
® PowerPoint
®
This process provides presentations without using a computer by converting
presentation files created with Microsoft
® PowerPoint
® into JPEG files, storing them on
a memory PC card, and displaying them in a slide show.
•To use this conversion mode, Microsoft
® PowerPoint
® must be installed on the
computer.
•Only static images are supported by this process. Animation and audio are not
supported.
Presentation files created with Microsoft
® PowerPoint
® usually
consist of several slides. For this reason, the tool creates a
folder with the name specified in step (5), below, and file for
each slide is created in the folder (starting with slide001.jpg).
(1) In the Conversion Method field, select Converting PPT file.
(2) In the File settings field, click on the Browse button for
PPT File Name.
The Open dialog box appears.
(3) In the Open dialog box:
(a) Specify the location of the file to be converted;
and
(b) Select the PowerPoint
® presentation file to
convert, then click on the Open button.
(4) In the JPEG Conversion Tool window, in the File
settings field, click on the Create button for New
folder name.
The Folder create dialog box appears.
(5) In the Folder create dialog box, in the Folder Name of
document field, specify a folder name of 12 characters or less.
(6) In the Folder create dialog box, click on the Selection
button.
The Browse Folders dialog box appears.
(7) In the Browse Folders dialog box:
(a) Specify the location in which to save the folder; and
(b) Click on the OK button.
(8) In the Folder create dialog box:
(a) Click on the Create button.
A confirmation dialog box appears;
(b) Click on the OK button.
(9) (a) In the JPEG Conversion Tool window, click on the
Conversion button.
(b) A confirmation dialog box opens. Click Ye s.
The computer begins to convert the file. When it finishes, a message appears
informing you that a JPEG file has been created.
Making a presentation with converted JPEG files1) Copy the folder created by the JPEG Conversion Tool, or its contents, onto a memory
PC card.
2) Use the steps 
1, 2 in “Projecting images stored in a memory PC card” 
p.41
 to
display a list of thumbnails.
3) Follow the instructions in step 
3 to find slide001.jpg (the first slide), and move the
orange frame over it (select slide001.jpg).
4) Set the remote control to [PJ Mode], and press the 
 button. An enlarged view of the
first slide appears on the screen. This starts the presentation.
5) To continue to the next slide, click on the remote control’s 
 button. To go back to the
previous slide, click on the 
 button.
Creating a screen capture and converting it into a JPEG file
This function saves the current computer screen as a JPEG file.
(1) In the Conversion Method field, select Creating screen
capture.
(2) In the File settings field, click on the Browse button for File
name after conversion.
The Save As dialog box appears.
(3) In the Save As dialog box:
(a) Specify the location in which to save the converted file;
(b) Enter a file name of up to 8 characters in the File Name
field; and
(c) Click on the Save button.
(4) (a) In the JPEG Conversion Tool window, click on
the Conversion button.
(b) A confirmation message appears. Click Ye s.
The computer creates a screen capture, and
converts it into a JPEG file in the specified
location. When it is finished, a message
appears to tell you that a JPEG file has been
created.Note•The maximum resolution of JPEG files created with the JPEG Conversion Tool is 1,024
x 768 pixels.
How to use the supplied software (Continued)
(1) (1)
(2) (2)
(4)-(a)
(4)-(a)
(3)-(b) (3)-(c) (3)-(a)
(4)-(b) (4)-(b)
(1)
(2)
(4)
(9)-(a)(1)
(2)
(4)
(9)-(a)(3)-(b) (3)-(a)
(6)(6)
(8)-(a)(8)-(a)
(6)
(8)-(a)(5)
(5)(5)(7)-(a)
(7)-(b) (7)-(b)
(8)-(b)
(8)-(b)
(9)-(b)
(9)-(b) 
						

							65
64
Others
The indicator lights inform you of internal abnormalities.
No power⇒Problem with projector
•Unplug the power cord, and contact your dealer.Lamp went out during use, or won’t come on⇒Returns to standby after about 2 minutes. If the projector fails to
operate normally after turning the power back on, either the lamp
needs replacing, or there is a problem with the projector.
•If a lamp burns out, replace it with a new one.
•Unplug the power cord, and contact your dealer.Power went out during use, or power won’t come on⇒Internal overheating, or the outside temperature is too high.
•Place the projector so that the air intake and exhaust are not
blocked.
•Unplug the power cord and wait for a shor t while, then turn the
power back on.
•Clean the air filter. 
p.56
❈The 
 icon will appear before the power goes out.
❈After displaying the abnormal state for about 2 minutes, returns
to standby.
Power went out during use, or power won’t come on⇒Problem with internal cooling fan.
•Unplug the power cord, and contact your dealer.
❈The 
 icon will appear before the power goes out.
❈After displaying the abnormal state for about 2 minutes, returns
to standby.
Power went out during use, or power won’t come on⇒The lamp cover is not properly attached.
•Unplug the power cord, and reattach the lamp cover. 
p.58
❈The 
 icon will appear before the power goes out.
❈After displaying the abnormal state for about 2 minutes, returns
to standby.
PRECAUTIONS•Make sure to unplug the power cord if something goes wrong.
•If the power cord is unplugged before cooling is complete, give the lamp time to cool
before plugging it back in. If the lamp overheats it may fail to light. Unplugging the power
cord repeatedly when the temperature is high will shorten the life of the lamp. (Even if
you are not concerned about lamp lifetime, the light may not come on if you do not wait
at least 3 minutes.)Trouble indications
ON LAMP TEMP
FA NON LAMP TEMP
FA NON LAMP TEMP FA NON LAMP TEMP FA NON LAMP TEMP
FA N
or (Red lit)
(Off)
(Red lit) (Red lit)
Or
(Green lit) (Green lit)(Red lit) (Red lit)
Or
(Off)Or
(Orange lit)
Or
(Orange lit or flashing) (Red lit or flashing)(Red lit)
(Orange
flashing)(Red lit)
If you think something is wrong, check the following before contacting customer service.
Please see “Trouble indications” 
p.64
 as well.
If  This Happens Check
No powerPower goes out
during useNo pictureNo audioPicture not
displayed
correctlyPicture blurred
Part of picture
out of focusImage is darkColors too light
Bad shadingRemote control
doesn’t workBefore calling service personnel
•Is the power cord plugged in? Is it connected to the projector?
•Is the lamp cover loose? 
p.64
•Is the ambient temperature high? 
p.64
•Is the air filter clogged? 
p.64
•Is the air intake or air exhaust blocked? 
p.64
•Is the projector turned on? 
p.27
•Is the mute function on? 
p.30
•Is the brightness setting minimized? 
p.53
•Are the connections set up correctly? 
p.22
•Are all the connected devices functioning properly?
•Is the projector turned on? 
p.27
•Is the mute function on? 
p.30
•Is the volume setting minimized? 
p.28
•Are the connections set up correctly? 
p.22
•Are all the connected devices functioning properly?
•Is the input signal supported by the projector? 
p.68
, p.69
•Is the correct video mode selected? 
p.29
•Is the correct signal format selected?  
p.29
•Is the selecting of RGB or Y/P
B/PR input correct? 
p.27
•Is there something generating an abnormal video signal, for
instance the video tape?
•Is the lens dirty? 
p.57
•Is the lens focus adjusted optimally? 
p.28
•Is the projection distance within the projector’s supported range?p.21•Is the projector’s screen placement angle tilted too far?  
p.21
•Are the sharpness or sampling phase adjustments off? 
p.53
 p.29
•Are the brightness or contrast adjustments off? 
p.53
•Is the lamp nearing the end of its service life? 
p.32
•Are the color, tint, R-level, G-level, or B-level adjustments off? 
p.53
•Is the screen dirty?
•Is the lamp nearing the end of its service life? 
p.32
•Are the remote control’s batteries drained?
•Are the batteries inserted into the remote control correctly? 
p.19
•Is the remote control being used within the effective range? 
p.19
•Are there any obstructions between the remote control and
projector?
•Is the correct operation mode set? 
p.20
•Are there any fluorescent or other bright lights shining at the
projector’s infrared remote sensor? 
						

							67
66
Others
If  This Happens Check
Mouse remote
control doesnt
workMemory PC card
images arent
projectedThe wireless
LAN PC card
doesnt workThe images from the
document camera
are blurryThe images from the
document camera
are flickering
• Are the USB cable and mouse remote control receiver (Models
equipped with PC card slot) correctly connected? 
p.51
•Do your computer and OS support USB?
• Is the remote control in [PC Mode]? 
p.20
•Are there any obstructions between the remote control and
projector/mouse remote control receiver?
• Is the memory PC card inserted correctly?
• Is a PC card not supported by the projector inserted? 
p.40
•Is the CARD indicator red? 
p.23
•Are there any JPEG files saved on the memory PC card?
• Are the files too large or in an unsupported format for the
projector?
Convert them with the supplied software application. 
p.61
•Is the wireless LAN PC card inserted correctly?
• Is a wireless LAN PC card not supported by the projector inserted?
The operation of cards other than the supplied product is not
guaranteed.
• Is the CARD indicator red? 
p.23
•Are the transmission mode and channel properly configured? 
p.34
•Are there any obstructions between the computer and projector?
• Do your computer and OS support the supplied software
application? 
p.24
•Is the document imaging camera’s lens dirty?
• Is the document imaging camera out of focus? 
p.45
•Is the location of the object being focused too dark?
• Is there impact from the room’s fluorescent lighting?
Turn off the fluorescent lights, or change the shutter speed settings.p.29
Before calling service personnel (Continued)
Specifications■ List of general specifications
Item Specification
Consumption Power 240 WWei ght TLP-T700/T500: 3.4 kg TLP-T600/T400/S200: 3.3 kg
TLP-T701/T501: 4.1 kg TLP-T601/T401/S201: 4.0 kg
Models without document imaging camera:
External Dimensions 298 
× 97  × 249 mm (W  × H  × D)(including protruding parts)
Models equipped with document imaging camera:298  × 97  × 313 mm (W  × H  × D)
Cabinet material* PC+ABS resin and ABS resinConditions for usage
 environment
Temp: 0°C to 35°C; relative humidity: 30% to 70%
Display method
3-panel transmission
Panel size
0.9 inches
LCD Panel
Drive system
TFT active matrix
Picture
TLP-T series: 786,432 pixels (1,024H  × 768V)
elements
TLP-S series: 480,000 pixels (800H  × 600V)
Lens Zoom lens F=1.9-2.3 f=35.6-44.5 mmLamp High-pressure mercury lampProjection screen size 32-300 inchesProjection distance 1.50-11.74 mSpeaker 1 W (Monaural)
COMPUTER-1,2 terminals
Mini D sub 15 pin   RGB / Y/P
B/PR  (dual use)
MONITOR terminal Mini D sub 15 pin   RGB / Y/P
B/PR (dual use)
S-VIDEO terminal Mini DIN 4 pinVIDEO terminal RCA Pin Jack, 1 V (p-p), 75  ΩAUDIO (L/R) terminal RCA Pin Jack × 2, 1.5 V (rms); 22 k Ω or moreAUDIO terminal 3.5mm dia. stereo mini-jack, 1.5V (rms); 22 k Ω or moreCONTROL terminal Mini DIN 8 pin (RS-232C)USB terminal Type B
PC card slot PC Card Standard TYPE II compliant (Models equipped with
PC card slot)
*
Each plastic part displays the materials it is made from, in order to fa\
cilitate recycling after this
product’s use had ended.■
Document camera specifications (Models equipped with document camera)
Item Specification
Lens F=2.8, f=3.4mmFocusing Manual  operationZooming None (adjusted through distance from subject)Gain Auto/manualImage element 1/3 inch CCDEffective pixels for pickup section
805,486 pixels (1,034H x 779V)
Lighting LED
Connection terminal 
						

							69
68
Others

List of supported signals (RGB signals)This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
(Press the AUTO SET button, and adjust automatically or manually.  
p.29
 )
Mode
720x400_85
VGA_60
VGA_72
VGA_75
VGA_85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85
MAC16
XGA_43i
XGA_60
XGA_70
XGA_75
XGA_85
MAC19
SXGA1_75
QuadVGA_60
QuadVGA_85
SXGA3_60
SXGA3_75
SXGA3_85
SXGA+
UXGA_60
UXGA_65
UXGA_70
UXGA_75
UXGA_85
1792x1344_60
1856x1392_60
1920x1440_60Refresh rate
(Hz)
85.039
59.940
72.809
75.000
85.008
56.250
60.317
72.188
75.000
85.061
74.550
86.957
60.004
70.069
75.029
84.997
74.700
75.000
60.000
85.002
60.020
75.025
85.024
60.012
60.000
65.000
70.000
75.000
85.000
60.000
60.000
60.000H-frequency
(kHz)
37.927
31.469
37.861
37.500
43.269
35.156
37.879
48.077
46.875
53.674
49.725
35.522
48.363
56.476
60.023
68.667
60.134
67.500
60.000
85.938
63.981
79.976
91.146
63.973
75.000
81.250
87.500
93.750
106.250
83.640
86.333
90.000Clock
(MHz)
35.500
25.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.250
57.283
44.900
65.000
75.000
78.750
94.500
79.857
108.000
108.000
148.500
108.000
135.000
157.500
118.094
162.000
175.500
189.000
202.500
229.500
204.750
218.250
234.000 Resolution
720 x 400
640 x 480
800 x 600
832 x 624
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
1400 x 1050
1600 x 1200
1792 x 1344
1856 x 1392
1920 x 1440
Note•Signals whose resolution exceeds the LCD panel’s number of pixels 
p.67
 will be
compressed. For this reason, some information may be lost, or image quality may be
affected.

List of supported signals (Y/P
B/P
R signals)
Signal format fh(kHz) fv(Hz)
480i(525i)@60Hz15.73 59.94
480p(525p)@60Hz31.47 59.94
576i(625i)@50Hz15.63 50.00
576p(625p)@50Hz31.25 50.00
720p(750p)@60Hz45.00 60.00
720p(750p)@50Hz37.50 50.00
1080i(1125i)@60Hz33.75 60.00
1080i(1125i)@50Hz28.13 50.00
1035i(1125i)@60Hz33.75 60.00
1152i(1250i)@50Hz31.25 50.00

List of supported signals (Video, S-Video signals)
Video mode fh(kHz) fv(Hz) fsc(MHz)
NTSC 15.73 60 3.58
PAL 15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41
PAL-M 15.73 60 3.58
PAL-N 15.63 50 3.58
PAL-60 15.73 60 4.43
NTSC4.43 15.73 60 4.43

Pin assignment of COMPUTER-1/2 & MONITOR terminals
5 11015 11
6
Mini D sub 15 Pin connector
Input Signal
•RGB inputR/G/B signals: 0.7V (p-p) 75 Ω
Horizontal sync signal: TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity)•Y/P
B/PR input
Y signal: 1.0V (p-p) 75 Ω
PB/PR signals: 0.7V (p-p) 75 Ω
Specifications (Continued)
∗ Do not connect anything.Pin Pin descriptionNo. During RGB input
During Y/P
B/PR input
1
Video signal (R)
Color difference signal (P
R)
2 Video signal (G) Luminance signal (Y)3 Video signal (B)
Color difference signal (P
B)
4 GND∗5 GND∗6 GND (R) GND (P
R)
7 GND (G) GND (Y)8 GND (B) GND (P
B)
9 N.C∗10 GND∗11 GND∗12 N.C∗13 Horizontal sync signal∗14 Vertical sync signal∗
15 N.C∗ 
						

							70
71
Others
Specifications (Continued)
CONTROL terminalPin assignment
78 6 34
5 12
Signal Name
RXD
CTS
DSR
GND
RTS
N.C
TXD
N.C Pin No.
1
2
3
4
5
6
7
8Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
No connection
Mini DIN 8 pin connector
Interface format
1 Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:  1 bit
2 Communication format STX (02h)  Command (3Byte)  ETX (03h)
Only 1 command valid per communication.
3 Data format For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
4 Replies Acknowledge ACK (06h) No acknowledge NAK (15h)
If commands are to be sent consecutively, wait for the response from the projector
(ACK or NAK) before sending the next command.
Main CommandsNote•Contact your dealer for control cable and other commands.
Separately Sold Product
Replacement Lamp Model TLPLW1Note•Design, specifications, etc. subject to change without notice for improvements, etc.
Item Command
Power onPONPower offPOFOSD display onMO0OSD display offMO1Auto setting (RGB input)PATStatus display onDON
Status display offDOF
Item Command
Computer (1) input selectIN1Y/P
B/PR (1) input selectIN2
Computer (2) input selectIN3Y/P
B/PR (2) input selectIN4
Video input selectIN5S-video input selectIN6PC card input selectIN7
Camera input selectIN8