Toshiba Projector Tlp T501 User Manual

21
20
Preparations
■Switching operation modesOperation modes should be switched between projector operation and compu\
ter operation.
ON/
STANDBYAUTO
KEYSTONE
MUTE
AUTO 
SET FREEZE INPUT
R-CLICK
PJ MODE LASER
VOL.
+
VOL.-
MENU 
/ ENTER
RESIZEOFF
Notes•See page 51 for more information on operating a computer.
• For the remainder of this manual, buttons, including those on the contro\
l panel (main unit
side), are referred to as follows:
Selection button  ⇒ 
 
 
 
; MENU/ENTER button  ⇒ 
With the exception...

23
22
Preparations
Before connection•Read the owner’s manual of the device to be connected to the projector.
•Some types of computer cannot be used connected to this projector.
Check for an RGB output terminal, supported signal 
p.68
, etc.
•Turn off the power of both devices before connection.
•The figure below is a sample connection. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Notes•COMPUTER terminals 1 and 2 function...

25
Operations
24
Connecting the power cord1
Insert the power cord connector into the AC IN socket of the projector.
2
Insert the power cord plug into a wall or other power outlet.
ON/STANDBYINPUT
MENU
AUTO
SET
FAN
TEMP
LAMP
ON VOL.
+
VOL.-AUTOK
E
Y
S
T
O
N
E
FAN TEMP LAMP ON
Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat.

 Turning the power on
Press the ON/STANDBY
button.The power turns on, and the
following 3...

27
Operations
26
INPUT R-CLICK PJ MODE LASERVO L.
+
VOL.-
MENU / ENTER
Preparations•Place the projector, and correctly connect all devices.
•To operate via the remote control, [PJ MODE] 
p.20
 must be
selected.
Press the PJ MODE button. The button lights up. This light
will go out 30 seconds after operations are complete. If
necessary, press the button again.
1
Turn on the power.Turn on the power, following the instructions in “Turning on the power” 
p.25
.
2
 Select language (When using for first...

29
Operations
28
ON/
STANDBYAUTO
KEYSTONEMUTE AUTO SET FREEZEINPUT R-CLICK PJ MODE LASERVOL .
+
VOL .-MENU / ENTER
RESIZE
OFF
ON/STANDBY
INPUTFAN TEMP LAMP ONVOL.
+
VOL.-
AU TOKEYSTONE
MENU
AUTO SET
Using handy featuresTo operate via the remote control’s 
 
 
 
 
 buttons, [PJ MODE] must be
selected. Press the PJ Mode button. The button lights up. This light will go out 30
seconds after operations are complete. If necessary, press the button again.

Using auto setting (Auto setting)
This function sets...

31
Operations
30
ON/
STANDBYAUTO
KEYSTONEMUTE
AU
TO SET FREEZE INPUT
R-CLICK
PJ MODE LASER
V
OL.
+
VOL.-MENU  / ENTER
RESIZEOFF
■ Freezing the image (Freeze)
The image being projected can be made to be frozen. This function is to
be used to pause a video during a presentation, etc.
Press the remote control’s FREEZE button.The picture is paused. The Freeze function is released when
pressing the FREEZE button again.Notes•The 
 icon will appear while freeze is in effect.
• The freeze function can be used on...

33
Operations
32

Displaying Information [Status display]
This displays information about the input signal, lamp use time, etc.
Press the 
 button twice.
When the 
 button is pressed once, the Setting display menu appears. Pressing
it again displays information 
p.52
. The table below shows what kind of information
is displayed. Press the button again to dismiss the display.
“Ye s”: displayed, “No”: not displayed
Item Description
Computer Y/P
B/PR
Video
PC Card CameraS-video
Input Input source name Yes...

35
Operations
34
■Displaying a computer’s screen via the projector1
Launch the Wireless Utility software
application.When the  Wireless Utility  launches, the  Screen
image  transmission mode window appears on the
computer screen.
To  switch to the  Screen image  transmission mode
window from another mode ( File or Document
camera ), click on the  Screen Image  icon 
.
2 Select Transmission mode.Click on  Update automatically  or  Update manually . See step 
6 for the meanings of
Update automatically...

37
Operations
36


Displaying a JPEG image saved on a computer via the projector
1
Launch the Wireless Utility software application.The Screen image transmission mode window appears on the computer’s screen.
2
Click on the File icon 
.
The Wireless Utility window
changes to File transmission
mode.
3
Click on the Browse button, and select the
file to send.Clicking on the Browse button displays the Open
dialog box. Select the file to send, then click on the
Open button.
The selected file is added to the...

39
Operations
38
3
Select the projector to be operated.In the Remote Control  window, click on the 
 button, and
select the desired projector from the pull-down list.
Only one projector can be selected. (It is not possible to operate
multiple projectors.)
Then icon 
  is displayed on the projector’s screen for few
seconds.
4
Click on the Remote Control window’s buttons.The function of each button and box is as follows:
Power On :Turns projector power on.
Power Off :Turns projector power off.
Note,...